Search Documents

By T. N. Singh, M. M. Singh, R. B. Singh

Fly rock is common when blasting shallow holes and during secondary blasting. Although the required quantity of explosives for secondary blasts is less, noise and fly rock can have an enormous environmental impact. This paper mainly deals with field experiments on blast-design parameters and addresses some precautionary measures that can be taken when pop shooting.

Jan 1, 2000

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent com¬parative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging.

Jan 1, 1987

By R. K. Mehta

An electrochemical coal oxidation model involving heterogeneous kinetics is presented. This model was tested by collecting current transient data on three coals assaying different ash content under varying operating conditions such as particle size, temperature, and % solids. In all cases, the model fitted the data very satisfactorily. Three intrinsic rate constants, namely mass transfer coefficient of Fe(II) Ions diffusing from solution to the anode (kma), mass transfer coefficient of Fe(II) Ions diffusing from solution to the coal surface (kmc), and chemical rate constant for coal oxidation with respect to Fe(III) at coal surface (k), were calculated. It was interesting to note that in this system, the mass transfer at anode was as important as the chemical reaction at the coal surface. The validity of this model was further demonstrated through a comparison of the activation energy of coal oxidation: firstly, by utilizing calculated chemical rate constant and assuming Arrhenius' type of relationship: secondly, by utilizing conventional approach using limiting current values. The comparison revealed that agreement was quite close. This kinetic analysis is useful because such a model can be used in predicting the intrinsic rate constants so that the relative importance of mass transport can be rationally analyzed.

Jan 1, 1991

By A. Moergeli, Philip Sander, John J. Reilly

"Estimating and managing the costs of complex infrastructure projects – in the planning/design and construction phases, for both owners and contractors – has been a challenge for decades. The more complex and technologically advanced the project, the greater the uncertainty, including potential risks that are important to owners and contractors, such as:• Cost risks to owners – meeting budget and schedule, maintaining public credibility.• Cost risks to contractors – profit, consequences of loss, impacts to reputation/future work.This concern has been addressed in various ways by the underground construction industry for some time (Reilly, 2001). In particular, while significant advances have been made in cost estimating for the planning and design phases (Reilly et al., 2004), that are important to agencies and political decision-makers, it is not apparent that these advances have been widely adopted for construction cost estimates. The reasons for this may relate to lowbid considerations – any method that tends to increase the contractor’s cost estimate, by including risk or likely costs, could lead to an erosion of the contractor’s competitive position – if others are not similarly required to include such costs.Different cost estimating methods produce different levels of information. Specifically, there is a large difference in the character and depth of information if a deterministic (quantities times price plus a contingency) and risk-based cost methods are used. It is this difference in character and depth of information that is the reason that risk-based cost estimating has potential value for owners and contractors. Figure 1 presents hypothetical cost results from deterministic and risk-based methods and illustrates some of these differences.In Fig. 1, the results for deterministic and risk-based cost estimates are given related to the potential profit or loss for a typical project. As is evident in this example, there is significant potential for costs to be realized that are higher than the proposal/bid value estimated using a deterministic approach, with a 15 percent probability of a loss. There is a 30 percent probability that the project will have a reduced profit. There is a 55 percent probability that the project will return a good profit. Using a risk-based approach, it is possible to better recognize this potential outcome in the bid phase and, as a consequence, develop a strategy to:"

Apr 1, 2016

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By Y. Gonzalez

The reaction kinetics of sulfuric acid leaching of brass foundry flue dusts were studied. As received flue dusts were separated into two size fractions, a coarse fraction (median size 103.5 microns) and a fine fraction (median size 3.4 microns). Experiments were performed on both fractions al-though most results are reported for the coarse fraction. Leaching experiments were conducted in a stirred reactor to determine those factors which govern the kinetic response of the sys-tem. The kinetics were followed by determining the increase in the concentration of dissolved copper with time. The effects of temperature, concentration and oxygen partial pressure on the rate of copper dissolution were examined. In addition, reaction residues were examined by SEM, EDAX and X-ray analysis. An activation energy of 4.8 kcal/mole (20.08 kJ/mole) was calculated. The rate was found to be significantly dependent on oxygen partial pressure and acid concentration. The order of the reaction with respect to oxygen partial pressure and hydrogen ion concentration was approximately 1.50 and 0.37, respectively. Results indicate that the dissolution reaction is limited by diffusion and can be described by the following mathematical expression where ~ is fraction of copper extracted in time t

Jan 1, 1988

By E. G. Cauda

Diesel engines are a major source of underground miners? exposure to nitrogen dioxide. In an effort to reduce the exposure of underground miners to regulated and unregulated diesel emissions, primarily particulate matter, mining companies in the U.S. are retrofitting existing and introducing new engines with various exhaust aftertreatment technologies. Different aftertreatment devices, or changing the operating temperature of a selected device, can have unexpected effects on the concentration of nitrogen dioxide emitted by a diesel-powered piece of equipment. This paper provides an overview of the effects different exhaust aftertreatment technologies available to the mining industry have on no2 emissions.

Jan 1, 2010

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By Y. Luo, S. S. Peng

Several issues deserve further attention to improve subsidence prediction accuracy. These include: subsidence initiation and development over a setup entry area; subsidence development after face stop; and subsidence over chain pillar. An intensive subsidence monitoring program has been carried out over several longwall panels. A large amount of subsidence data has been collected, analyzed and solution techniques developed. In this paper, some of the measured data. data analysis techniques and the developed prediction methods are presented.

Jan 1, 1992

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002

The concept of classification in wet, closed circuit ball milling is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters that effect fines removal are identified and discussed, and a quantitative index for circuit classification effectiveness is presented.

Jan 1, 1987

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By Slobodan Vujic, Goran Cirovic, Dragan Radojevic

Mine production systems (MPS) are characterized, more or less, by the following properties: uncertainty, subjectivity, impreciseness, polysemy, instability, indefiniteness and lack of data. From modern study aspect these MPS mathematically belong to the class of fuzzy systems. With this in mind, the usage of fuzzy sets is recommended as a methodology that treats impreciseness, indefiniteness and complexity of mine production systems in a satisfactory manner. Fuzzy modelling, discussed in this pa- per, is applied as a mathematical implement. The objective of the paper was to show production optimization in practice on the ex- ample of bauxite open pits where fuzzy linear programming (FLP) was used following the criterion per income. The variables in criterion function are linguistic variables while both variables and variable restrictions are presented by triangular fuzzy numbers (TFN). The term "satisfactory income" presented through triangle fuzzy numbers was introduced instead of "maximizing the income". sensitivity of the obtained solutions has been analysed

Jan 1, 1996

By K. A. Natarajan, Namita Deo

The interaction of Bacillus polymyxa and minerals such as hematite, corundum and quartz resulted in significant surface chemical changes, both on the cell surfaces and on the interacted oxide minerals. After such treatment, quartz was rendered relatively more hydrophobic, while hematite and corundum were rendered more hydrophilic. Biopretreatment was observed to be beneficial in the separation of silica from hematite and alumina by both selective flocculation and flotation. The possible role of bacterial adhesion and metabilites in the biobeneficiation process is illustrated.

Jan 1, 1998

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Richard J. Frechette

Final reclamation of mine tailings impoundments typically involves addressing the broad issues of surface stabilization and water management. Surface stabilization includes immobilizing the tailings particles and providing long-term protection of the containment facility. Water management typically includes provisions for handling both the external water (rainfall and runoff) and the internal water (pore fluids). Wet tailings disposal facilities, and sites with limited access and steep topography, present challenges to implementing effective surface stabilization and water management plans. This paper presents a generalized discussion of the approach to tailings impoundment reclamation based on project experience.

Jan 1, 1995

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979