Search Documents

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By Mohamed A. Younis, Robert J. F. Goodfellow

This paper investigates the design approaches taken and the philosophy employed during the construction of the Metropolitan Airport Commission (MAC) storm tunnels, part of the Phase 4 Segment of the MAC Trunk Storm Sewer Project at Minneapolis St.-Paul International Airport, located in Minneapolis, Minnesota. URS Corporation was retained to provide a design and Construction Management (CM)services for the MAC Trunk Storm Sewer Project. A case history of the design and construction challenges of the project is presented. The MAC storm tunnels consisted of the construction of twin 10-foot inside diameter (I.D.) tunnels within 7 feet of an existing 72-inch I.D. storm pipe at the base of a 70-foot high highway embankment. The analysis required during the design stage of the project is discussed. This analysis and our design approach provided a defensible framework and justification to make design decisions on relevant issues including: allowable spacing of new and existing structures; preferred order of construction; expected ground deformation behavior; response of lining types to adjacent construction; and effects of proposed changes to design at the submittal stage and during construction.

Jan 1, 2003

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

By Douglas M. Smith

The town of Tayoltita, Durango is located at the bottom of the 2000 m. deep Rio Piaxtla canyon on the axis of the rugged Sierra Madre Occidental mountain range. Throughout most of the year access to the town is restricted to travel by mule or STOL aircraft. Silver and gold have been produced from epithermal veins in the north side of the canyon since 1757. During the last seventy-three years more than 4,588,000 kg. of silver and 76,322 kg. of gold have been produced from approximately 6,000,000 metric tons of ore. The Tayoltita mine is developed within a fault block bounded by normal faults which strike north-northwest and have opposing dips. A thickness of at least 1300 meters of late Cretaceous or early Tertiary volcanic rocks is exposed in the mine. These range in composition from andesite to rhyolite. Andesite predominates in the upper 750 meters of the section. The volcanic rocks were passively intruded by quartz-monzonite and andesite stocks during middle (?) Tertiary time. Mineralization spatially and temporally (?) related to the stocks occurs along the east boundary fault and in intersecting footwall fissures which strike east-west and northeast. Ore was deposited over a vertical range of up to 600 m. prior to tilting of the volcanic rocks 35 to 45° to the east. With few exceptions, the ore bodies are found within the lower 400 to 500 m. of the andesite. Argentite (acanthite), stromeyerite, jalpaite, electrum and native silver are the principal ore minerals. They occur in gangue composed of one or more of the following: quartz, calcite, bustamite, adularia, chlorite, and albite. Base-metal sulfides make up less than 1.5 percent by weight of the ore.

Jan 1, 1974

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By T. Dlokweni, A. Z. Toper, A. P. Squelch, R. G. Gürtunca

A collaborative research programme called 'DEEPMINE' was established in 1998 to investigate and research the problems of mining below three and five kilometres depths. Backfill is considered as an important support strategy to alleviate rockburst and rockfall problems in current depths and it will even become a more crucial mining strategy at ultra-deep level mining. In this paper, the evaluation and the application of the current backfill design criteria to the ultra-deep level mining environment are studied and a new backfill design criteria is proposed. The new criteria suggests that backfill should still be placed 60 - 70% of the area mined with a maximum fill to face distance of three metres. Furthermore, the vertical stress generated in backfill should be between 2 - 3 MPa at maximum 25 metres from the face at a corresponding strain value of maximum 10%.

Jan 1, 2001

By S. Gundiah

Preparation of functionalized polymers from the polymerization of monomers and preformed polymers are discussed with a few illustrative examples. The methods of their characterization, with reference to their application in flocculation, are described.

Jan 1, 1987

By G. Jalkanen

Dealing with a trend in inverse distance estimation, IWD, is presented. A measurement is proposed to be consisted of a portion due to a mean and a portion due to a residual. The procedure consists of de-trending the measurement via a linear or nonlinear regression. Residuals are computed, and IWD parameter estimation is conducted on the residuals. Estimation at un-sampled points is then computed by estimating the mean and adding on the estimate of the IWD on the residual. A possible BOXCOX transform is also proposed.

Jan 1, 2010

By B. Petkof

Olivine has been an accepted industrial mineral for the last 50 years. Its initial acceptance was based on the recognition of its refractory properties by European research workers in the middle to late 1920's. Initial U.S. olivine production began in the early 1930's in North Carolina and continues there today. Olivine also is produced in the State of Washington and in other countries.

Jan 1, 1982

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By G. Robert Guillet

Nepheline syenite is a light-colored feldspathic rock that is used primarily as an addition to the glass batch. It is also used in ceramics and as an industrial filler. Composed essentially of the soda and potash feldspars and nepheline, nepheline syenite contributes needed alkalis and alumina to the glass composition. And because it contains a higher proportion of these oxides per unit weight, it is a formidable competitor for feldspar in northeastern North America and parts of western Europe. Nepheline-bearing rocks are not uncommon on a world scale, but few are able to be beneficiated to a composition sufficiently low in iron to be used in the making of glass. Nepheline can only form in an environment deficient in silica. Hence free silica, as quartz, is always absent in the primary mineral assemblage. Biotite, hornblende and magnetite are usually present as minor accessory minerals, and zircon, garnet, muscovite, and apatite may be present as trace minerals. Nepheline syenite is produced for glass, ceramics, and filler markets by Unimin Canada Limited at Blue Mountain, in south- eastern Ontario. Unimin acquired the former Indusmin and IMC properties from Falconbridge Ltd. in 1990. Elkem Nefelin AIS commenced production of similar products from Stjernoy Island in northern Norway in 1961. Unimin acquired this company in 1992. Nepheline has also been a byproduct of apatite mining on the Kola Peninsula for many years, and in 1951 the production of alumina from nepheline was commenced in a plant near St. Petersburg (Leningrad). There are now four plants in the Russian Republic, two smaller ones based on nepheline tailings from apatite mining and two larger and more recent plants in central Siberia using other nepheline resources. All four of these plants are integrated complexes that produce alumina for the subsequent production of aluminum metal, sodium and potassium carbonates, and portland cement. Roofing granules are produced by the 3M Company from a nepheline rock in Arkansas. In 1980 and 1989, trial shipments of nepheline syenite were recorded from new sources in Brazil and western Turkey respectively. Recent interest is also recorded for deposits in China, Saudi Arabia, and British Columbia.

Jan 1, 1994

By G. Rinelli, Paul R. Jr. Smith

Preparation for flotation begins with dragline mining, pumping, washing, screening, and desliming. Slimes, nominally -150 mesh material, constitute large quantities of phosphate and water which are a disposal problem. Older techniques involve sizing at about 35 mesh for separate coarse and fine treatment. The plus 14 mesh fraction does not require concentration. Coarse treatment includes agglomerate spiralling, belt flotation, thickening, scrubbing with sulfuric acid, de-oiling for reagent removal, and cationic flotation of fine quartz. A recent trend is to screen at coarser than 35 mesh size and eliminate coarse particle treatment, sacrificing some grade of this product. Techniques for flotation concentration of the fine size fraction are discussed.

Jan 1, 1976