Search Documents

By C. A. Wiggins

The new Niagara Falls Intake Tunnel, mined in the highly fractured Lockport Dolomite, encountered prolific inflows of water contained in rock seams directly linked to the Niagara River. These inflows were pressurized and, more significantly, contained high concentrations of dissolved H2S gas. The contractors attempts to control the water/gas inflows included cement and chemical grouting from inside the tunnel. Ultimately, improving the rate of air exchange in the tunnel by increasing the fan capacity, in conjunction with a pattern down-hole pre-grouting program along the tunnel alignment allowed the contractor to control the concentration of H2S gas and complete the tunnel.

Jan 1, 1997

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By M. D. Carter

The availability of environmentally acceptable and reliable energy sources is an important issue for Federal, State, and local planners. A cooperative program by the U.S. Geological Survey, State geological surveys, and the U.S. Bureau of Mines has developed a national GIS-based systematic effort to collect, analyze, and depict data characterizing the relationship between restrictions to mining and the potential development of the Nation's coal resources. Land use/environmental and technologic/geologic restrictions are identified within selected 1:24,000-scale, 130-to 150-sq-km 7.5-min quadrangles and applied as overlays to maps of coal-bed thickness, depth, and mined-out areas. Tonnages of original, mined and lost-in-mining, remaining, restricted, and available resources are calculated. Resultant data files are transferred to the Bureau of Mines for recoverability and cost analysis.

Jan 1, 1995

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

By Frank E. Kottlowski

Widespread high-calcium (HC) limestones in New Mexico and adjoining areas, are low in magnesium, but some units include shale interbeds that would be deleterious for usage in sulfur removal. In southwest New Mexico, southeast Arizona, and adjoining parts of Mexico, limestones in the thick Mississippian Escabrosa, Pennsylvanian-Permian Horquilla, and Cretaceous U-Bar units are HC as are strata in the Mississippian Lake Valley, Pennsylvanian formations, Permian Hueco, and parts of the Permian Capitan Limestone of south-central and southeast New Mexico and west Texas. In north-central and central New Mexico, many limestones in the Pennsylvanian Madera Formation are HC as are some of the Cenozoic travertines. In northwest New Mexico, where the present-day mine-mouth coal- fired power plants occur, there are no HC limestones, but to the north in southwest Colorado some beds of the Mississippian Leadville Limestone and Pennsylvanian Hermosa Formations are HC. HC limestones considered contain at least 95 percent calcium carbonate and less than 3 to 5 percent magnesium carbonate. Limits for other impurities are alumina, 1 percent; silica, 2 percent; sulfur 0.05 percent; phosphorous, 0.02 percent; and iron oxide, about 1 percent. Chemical and physical requirements differ slightly depending upon the ultimate use.

Jan 1, 1995

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By David A. Milligan

This paper describes the Darwin Silver Recovery project, located 66 km (40 miles) outside of Lone Pine, near Darwin, Inyo County, California. A lead-zinc mine and a flotation concentrator were operated there from 1945 to 1957. By the time the mine was shut down, 1.53 Tg (1.69 million short tons) of tailings had been stored in ponds. An average silver assay of 47 mg/kg (1.38 troy oz/st) of tailings stimulated interest for commercial silver recovery. A heap leach process was developed in 1981 at the Tucson Research Center of Anaconda Minerals Company, a division of Atlantic Richfield Company. Agglomeration techniques were used on the ore since the fine grind did not allow direct heap leaching. Lime and cement were required as binders, Early laboratory tests showed that recoveries equal to those from an agitated leach could be achieved at lower capital and operating costs. Laboratory tests determined cyanide requirements, lime and cement usages, and percolation or leach rates, as well as confirming that a zinc precipitation step could recover the silver from the leach solution.

Jan 1, 1983

By Frank E. Dalton, Bart T. Lynam, Forrest C. Neil

The Tunnel and Reservoir Plan (TARP) is the largest tunneling program in the history of the metropolitan Chicago area (Figure 1). Between September 1976 and September 1977, rock tunnel contracts having an estimated cost of approximately $420 million will be advertised. During the past six months, the Metropolitan Sanitary District of Greater Chicago (MSDGC) has awarded contracts for 16.5 miles of rock tunnels in diam of from 9 ft to 30 ft having a total bid price of $120,261,750. RECENT CONTRACT AWARDS Addison-Wilmette Tunnel $63,140,480 Upper Des Plaines #20 Tunnel 35,749,664 Upper Des Plaines #21 Tunnel 21,371,607 Addison-Wilmette Tunnel The first contract was advertised in September 1975. This contract, described as the Addison-Wilmette Tunnel, runs from Wilmette Harbor at Lake Michigan under the North Shore Channel to Addison Street in the City of Chicago, a distance of 10 miles. The contract calls for constructing approximately 27,750 linear ft of 30 ft ID and 24,020 linear ft of 22 ft ID unlined rock tunnels, excavation of two construction shafts, and the excavation of 32 drop shafts of various diam. Two hundred ninety-three companies were notified of this contract being advertised, 70 companies took out contract specifications and 3 companies ultimately submitted bids. The contract was awarded to a joint venture of:

Jan 1, 1976

By R. L. Ziegfeld

It has often seemed to me that people are too prone to turn to new and untried materials in an effort to solve their problems, without giving sufficient consideration to the old stand-bys, except as a last resort, It?s a little like middle-aged men who are swept off their feet by the fresh beauty of a young girl without first considering the many advantages that a more mature woman has to offer. Maybe it?s because, like the older woman, the older materials have to make a determined effort to keep themselves looking young and attractive. T at?s just about the situation with which the lead industry is laced. We have to make a determined effort to keep lead looking young and attractive to industry. However, there is one difference and it is important, Lead can not only be kept looking young, but it can, in fact, actually be kept young, This results from two things. First, industry and technology are constantly changing. For example, we have known for years that the density of lead makes it ideal to stop gamma rays, but it is only recently that atomic fission as a source of gamma radiation has become an important tool of industry, That makes old knowledge about lead useful in developing a new market for it.

Jan 1, 1958

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By James T. Curry

The steady growth of the Northwest portion of the United States over the past two decades, and the very rapid development of Northern California, Western Nevada, and Oregon in particular, led the Calaveras Cement Company people to Shasta County, California in 1957. The presence of a large deposit of high calcium carbonate limestone had been recognized for many years, but it required the momentum of an expanding economy to make these long known reserves valuable. This, plus the availability of a reliable supply of fuel in the form of natural gas, and the ready means of shipping the product to the consumer both by highway and railroad, seemed to offer the proper combination to launch a successful venture. The Calaveras Cement Company had been manufacturing cement by the wet process since 1925 at their plant at San Andreas, California. Starting with two small kilns, the plant in Calaveras County started an expansion program in 1945 that ultimately resulted in the plant as it exists today, consisting of five kilns with a combined production of 4.5 million barrels annually.

Jan 1, 1967

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.'s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By L. W. Ashton

Geochemical exploration guidelines were developed from a study of 460 rock chip samples collected at nine disseminated gold deposits in Nevada. Obtaining high grade Au samples is difficult because gold content is extremely variable, even over 8 m (25 ft) distances. For reconnaissance sampling, pathfinder elements are reliable indicators with threshold values of 100 ppm As, 1 ppm Hg, and 50 ppm Sb. Arsenic is the most reliable of the three elements, being significantly enriched in all deposits. If the pathfinder threshold levels are reached with low Au content, more samples should be collected. Successful disseminated gold exploration requires large numbers of samples.

Jan 1, 1990

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

When exploration shows a mineral deposit to be of importance, the subsequent work of defining the limits or boundaries of the ore body and preparing it for the extraction of the mineral is termed development (Young, 1946). In underground mining, development also connotes the work that is involved in opening up a deposit preparatory to stoping or productive operations. In this section, mine development is defined to include all studies and operations that will enable a sound evaluation of an explored ore body from the technical and financial standpoints. Though the ultimate objective of all mine development activities is the same, the scope and detail of these activities vary depending on the type of ore body (e.g., flat bodies, lenses and sheets, massive deposits, narrow veins, and bedded deposits), and the method of working the deposit (e.g., under- ground or surface methods or a combination of both of the methods). Therefore, the various contributions in section 3 address such topics as long-range planning, feasibility studies, and valuation for many types of ore bodies and different mining methods. This introductory review is divided into three major parts. In the first part, long-range planning aspects are briefly discussed with .an emphasis on current trends that affect mine planning. In the second part, an overview is provided of the contents in the mine development and valuation section. In the last part, remarks are made on the status, scope, and future of quantitative and computer methods in mine planning and development.

Jan 1, 1979

By Bruce A. McKinstry

For many major mining projects the time frame from initial planning to production can be measured in terms of decades. Hecla's Silver Shaft project, which is scheduled to go into production by the end of this year and includes a complete surface facility, shaft with an ultimate depth of 2,348 meters (7,700 feet), complete ore pass and loading pocket system, and 610 meters (2,000 feet) of development drifting and stope preparation, was initially concieved in the Fall of 1979. This duration of a mere four years from conceptual engineering to production is a testimonial to what can be accomplished when a progressive mining company and an innovative contractor work together as a team rather than developing into two warring camps as often happens.

Jan 1, 1983