Search Documents

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of'these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By Luther W. Hyde

Ground water, one of Florida's most valuable resources, is also one of its most abundant. The State is fortunate to have several prolific ground- water reservoirs that yield tremendous quantities of water to wells and to some of the world's largest springs. These ground-water reservoirs, or aquifers are of two types artesian and nonarteaian. Ad artesian aquifer is one that contains water under sufficient pressure to rise above the top of the oontaining formation. A nonartesian aquifer is one that contains water which is not confined, and the upper water surface (water table) is free to rise and fall. The principal source of ground water in Florida is the artesian Floridan aquifer which supplies most of the water users in the State. Nonartesian sources include the Biscayne aquifer of southeastern Florida, the sand-and-gravel aquifer of extreme western Florida, and a shallow aquifer which lies at depths of less than 100 feet over much of the State. The accompanying map shows the approximate areas where these aquifers are the main source of supply; however, the boundaries do not represent the areal extents of the aquifers. For example, the Floridan aquifer extends beyond the southern boundary shown on the map, but it is not of great economic significance there because the water is highly mineralized. Aquifers other than the four described occur in the State, but they are, for the most part, of minor significance. One of these is an artesian aquifer which is formed by permeable zones that occur locally within the confining beds above the Floridan aquifer.

Jan 1, 1966

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By Steven J. Schatzel, Kayode M. Ajayi, Bo H. Kim, Zoheir Khademian, Gabriel S. Esterhuizen

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a discrete fracture network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A fracture flow code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.006 m3/ s, significantly lower than the average inflow of 0.22 m3/ s for a shallow-cover mine (145-m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk.

Jun 19, 2022

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By J. L. Boyd

The mining and processing of basic metals relies on water as a medium for transport. Metallurgical ores are ground, concentrated, leached and refined in an aqueous medium. Water is used for temperature control during processing and in air pollution abatement during smelting. All of these process steps result in liquid wastes. Many of the aqueous wastes from ore processing areas become the raw product for a second stage and water recycling may begin. The point at which water recycling or reuse has been initiated in the past, rather than water discharge, was where water conservation was manditory due to a shortage, where process conditions would allow or benefit from reuse, and where economic considerations demanded reuse. The Fontana, California plant of Kaiser Steel Corporation is an example of an integrated steel plant that was forced to practice water conservation and reuse due to its location in an arid environment.1 Only a small amount of water required to maintain the water reuse system in balance with respect to dissolved solids and product quality is discharged. The Butte, Montana copper ore processing plant of The Anaconda Company obtains 66% of the water required for production by recycling, after clarification and chemical treatment, 30 MGD of wastewater from its tailings ponds. This operation is estimated to save the company about $1200/day over a once through water system.2 Here plant location and economics favored water reuse.

Jan 1, 1975

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By R. Jacobson

This paper presents comparison of proposed future solution and in-situ mining methods for in-situ leaching and recovery of uranium, gold, silver, and copper. We propose to show that in the future new extraction methods for each metal will eventually evolve for each hydrometallurgical process step, i.e. in-situ leaching, recovery, and concentration; precipitation and reduction; and drying, when required--without generating waste or bleed streams. In the future, to be highly profitable, these forms of mining will develop into an integrated system to eliminate waste streams using safe, powerful lixiviants. This integration will include, with some exceptions, improvements in the following areas of process development: 1. Lixiviant selection and in-situ leaching technique, 2. Target metal recovery and concentration (at a surface hydrometallurgical facility) from the circulating pregnant lixiviant stream, 3. Target metal precipitation or reduction, where decant water from the precipitate dewatering step is reusable for resin or solvent strip liquor (eluant), 4. Final preparation of target metal for sales, i.e. drying, purification, casting, packaging, 5. Restoration where most of the groundwater restoration process is performed at the same rate as multi-wellfield mining.

Jan 1, 1987

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

Introduction Surface mining is a business, and the objective of most businesses is to make as much money as possible within certain responsible constraints. Businesses normally measure their potential to make money by estimating the discounted cash flow rate of return on new projects or the net present value for ongoing projects. These estimators of profitability are calculated using the following well-known equation: [ ] where i is the year, n is the total number of years, A, is the after tax net cash generation in year I, r is the discount rate and NPV is the net present value. In its simplest form, when the value of r makes the NPV equal to zero, the discounted cash flow-rate of return (DCF-ROR) is defined. The maximum economically recoverable reserve is identified at the point where the NPV or DCF-ROR is at a maximum. Depending on the measure used (DCF-ROR or discount rate) for calculating the NPV, the definition of recoverable reserve will be different for exactly the same deposit. Maximization of the measure of profitability and the economically recoverable reserves should not be separated from the mining method and sequence of exploiting the reserve. The surface mining methods may involve multiple-pass development of the resource, mining to the ultimate limit in one pass or a combination of the two methods with backfill. Multiple-pass development When planning a multiple-pass mining operation, it is important to determine the width of pit expansions that are appropriate for a specific situation. Production personnel typically want wide, open work areas where operations can be set up to run at peak efficiency. While this is understandable, the trade-off between highly efficient production operations and an overinvestment in stripping should be carefully weighed. As long as safety is not compromised, a few cents per bank cubic yard increase in operating cost due to lower productivity by working in more confined spaces may well be offset by a decrease in the overall short-term stripping requirements. A mini study on productivity and cost should help quantify this cost before deciding on minimum phasing requirements. The bigger challenge associated with establishing smaller work areas is securing operations and management buy-in to marginally lower productivity when reporting results. When cost reduction is the important management goal and everyone is focusing on unit costs, one sometimes loses sight of the goal of total cost management and, even more importantly, maximum profitability. The first pit should be defined by the first grouping of recoverable mineral that has the highest after-tax unit value and forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. 1 is constructed for a rate of production, R, and a quality management strategy, Q, by calculating the NPV for a series of sequences, with each sequence assuming that the operations are terminated on successively lower profit pits. These values are plotted to form the curve in Fig. 1. If the operation ceases on a pit that has too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have made more money invested at the discount rate than by mining the next pit expansion. Therefore, the maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV. There may be an opportunity to refine the definition of the "ultimate pit" around the maximum-value point. The precise definition of the ultimate pit early in the mine life may or may not be important today, depending on how far off in the future these limits will be reached. By the time an operation must decide on its last increment of economically recoverable reserve. much of the

Jan 1, 2000

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock's unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock's shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By A. Durnan

Barrick Goldstrike Mines Inc. (Goldstrike) operates a six circuit (train) pressure oxidation plant for the pretreatment of gold bearing sulfide ores. The property is located 27 miles north of Carlin, Nevada. Since the commissioning and start-up of the first circuit in 1990 until the present total plant availabilities have exceeded 90%. The discussion that follows will detail the maintenance practices employed to consistently achieve this goal.

Jan 1, 1994

As we are all well aware, the demand for coal is increasing very rapidly. This makes the coal industry one of great opportunity for both the miner and the-supplier. Up until the middle 1960's, the price of coal had been one of the most stable of all commodities for the proceeding fifty years. In somewhat oversimplified terms this was because the inflationary tendencies had been offset by improved mine techniques and more efficient, more productive, and more reliable equipment; but, in the last seven years the price of coal has doubled. It is not the intent of this paper to discuss the many reasons for this price increase, but to show how the cost of hauling coal can be sharply decreased with a new truck concept. Not long ago a mining executive stated that all haulage trucks now available are basically the same. They look the same; they cost about the same; they have the same engine, power train, and tires; and, they have about the same operating cost. Truck size has increased which has reduced the number of drivers, but the purchase price and maintenance and repair costs have increased proportionally. Pits must be widened and loading shovels enlarged, out, all this has not reduced the cost of moving coal. Another executive said that he saw no advantage in buying new trucks because his people now know how to maintain and operate the ones they presently have. They have all the right spare parts along with a good maintenance program. Most replaceable parts of the trucks now in operation have been replaced and improved at least once and the trucks are now running better than when they were new. Besides, the trucks are no pretty well written off.

Jan 1, 1972

By Leena Suopajärvi, Karin Käär, Marcin Szumny, Jari Joutsenvaara, Md Ariful Islam, Helmut Mischo, Georg Meissner, Ossi Kotavaara, Catalina Vrabie

This study outlines implemented tactics and results for community empowerment through participation in questionnaire surveys, educational programs, and discussion on sustainable sourcing from new critical raw materials (CRMs) projects. Utilising questionnaire surveys, including the Public Participation Geographic Information System (PPGIS), the research gathered public opinions from Estonia, Germany, Poland, and Zambia, receiving 1,068 responses. These responses addressed various social, economic, and environmental issues related to CRM projects. Feedback from educational courses with participants from over 25 nations and public events provided additional insights. The collected data and feedback offer crucial input for advancing sustainable and responsible CRM sourcing strategies in these regions.

Feb 1, 2025