Search Documents

By D. G. Chedgy

Environmental improvement efforts are focusing with increasing intensity on pollutants resulting from combustion. The high cost of removing these pollutants at the power station is well documented. Physical coal cleaning has always been and should remain the most economic method of reducing sulfur oxide emission from coal combustion. It is critical in the selection of preparation plant circuitry to consider capital and operating costs, as well as the level of sulfur reduction. This paper describes the technical criteria which must be used for efficient process selection and summarizes the cleaning systems available or in development.

Jan 1, 1990

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By Charles C. Mosher

An in-mine seismic technique for detecting faults has been tested in a Western U.S. coal mine. This technique has been used extensively in the U. K. to help guide longwall mining operations. Explosives detonated on the face of a seam generate sound waves which propagate into the seam. Reflections from faults are picked up by sensors on the same face. Computer processing is then used to determine the fault locations. A known fault was successfully located in this test. Modifications to the U. K. procedures were required for the relatively thicker roan and pillar mines common in the Western U. S.

Jan 1, 1983

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its' cashflow position from negative to positive within two years.

Jan 1, 1991

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

By G. F. Revey

Most commercial explosives contain 70 to 94% ammonium nitrate, by weight. When portions of these explosives end up in shot rock and ore, through spillage or incomplete detonation, ammonia and nitrates leach out of them and into ground water. In recent years, State and Federal regulators have been applying more stringent water quality standards, particularly at new mines and development projects. Bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice at most mines, when mining conditions allow it. ANFO use is desired because it less costly than other explosives, but when spilled it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. They either control explosive losses, or they treat mine effluents at the end-of-pipe. This paper addresses the former solution --controlling explosive losses. For both packaged and bulk explosives, guidelines designed to limit losses during storage, handling and use, are described in detail.

Jan 1, 1995

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By Ken Criley, Marc E. Orman

Identifying the optimum ultimate height for heap leaching ore requires the consideration of a number of competing factors. A primary limitation is the reduction in the permeability of the ore with increasing heap heights. At low permeabilities the heap can blind off, cause serious ponding and runoff, and become very difficult to rinse at closure. The authors present a laboratory methodology that has been successfully used on several projects to identify the maximum height for controlling heap permeability.

Jan 1, 1996

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

"History - How did you get into mining and involved with SME?Unlike many past presidents, I do not come from a mining lineage. I liked math in high school and believed I wanted to be an engineer. I told my math teacher that, and he laughed in my face. I believe that humiliation is what carried me through engineering school. At the time my ability to go to college relied on how inexpensive I could make it. My brother told me that there were a lot of scholarships in mining engineering, and I should apply to mining schools. As usual, he was right and I was off to the University of Idaho to study. My first summer break I got a job with Hecla at a mine in Arizona. I was a laborer on a shotcrete crew. I knew after the first summer that I loved underground mining, and I never considered changing disciplines. Looking back, I was working in miserable conditions (hot, humid), on a miserable job (shotcrete), where I got injured, and two summer student roommates died in a car accident on the commute home after work. I had every reason to hate the industry, as I had seen virtually everything bad about what we do. But I didn’t, I loved it. I said I was good at math, I never said I was smart.I joined SME in college because I was told to by the head of the mining school, Dr. Jack Hoskins. You did what Jack told you to do. I got involved because I went to an annual meeting and the papers in the underground sessions were terrible. I refer to bad papers as the “Tensile strength on cable bolts in sub-arctic regions on Tuesday” papers. Real snoring fodder. I don’t remember who I was complaining to, but they told me to quit my grumbling and fix it. So I chaired a session, and tried to get only good quality papers, something that has been my mantra for years with the Mining & Exploration Division. I also volunteered to help the local sections too. Then one day I woke up as president.What is your opinion of the health of the mining industry?The mining industry is in bad shape. Coal is under attack and will likely never recover to its former greatness. Our President has banned new coal leases, and the state of California is forcing people it does business with to divest their interests in coal companies. And that all happened in just in a few short weeks this January. Usually in America you get a trial before you are given a death sentence, but not with coal."

Jan 1, 2015

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By Nath S. Parate

With the extension of mining beneath residential and industrial areas, it is becoming increasingly necessary to extract coal and minerals in such a way that subsidence damage due to groundmovement is reduced to a minimum. Understanding clearly of the mechanism of subsidence development is a must in view of the environmental problems and the energy crisis today. This paper gives a simple analysis of various components resulting from subsidence and the influence of other factors on their development. An up-to-date review of the subsidence and strain profiles is presented, with particular references to the coal mining operations. The importance of this topic from mining damage to structures, buildings properties and environment in mining areas is undeniable. Field results are discussed.

Jan 1, 1982

By A. Singh, C. Da Corte

"South Africa possess the biggest fluorspar reserves in the world followed closely by China. In light of the current commodity downturn this paper explores the use of Dense Media Separation (DMS) as a coarse pre-concentration method for two fluorspar deposits located in South Africa in which the dominant gangue is carbonate present in the form of dolomite and calcite. Heavy Liquid Separation indicated that conventional pre-concentration of the drill core samples from both deposits would result in unacceptably high fluorite CaF2 losses. At a maximum CaF2 loss to floats of 5% the benefit of DMS would be economically marginal and difficult to justify as a conventional pre-concentrator. In light of cashflow constraints, a twin flowsheet was proposed for the sole purposes of upfront cash generation in which the majority (67-77%) of the CaF2 would report to a high grade flotation plant in 38-41% of the mass whilst the rejects would be stockpiled for flotation at a later stage. Considering the proposed twin flowsheet approach the high grade product split was achieved using DMS and this paper documents the challenges encountered and results achieved. INTRODUCTION Fluorspar is the commercial term for the mineral fluorite (calcium fluoride, CaF2). Worldwide production of fluorspar is dominated by four countries namely China, Mexico, Mongolia and South Africa. Although South Africa is the fourth largest producer, it has the largest fluorspar reserves closely followed by China (U.S. Geological Survey, 2017a). Fluorspar is broadly categorized into two grades namely acid grade also referred to as acidspar (>97% CaF2); and sub-acid grade (ceramic and metallurgical grade) commonly referred to as metspar (=97% CaF2). Acid grade fluorspar is used for the production of hydrofluoric acid (HF) which in turn is used for the manufacture of fluorocarbons and semi-conductors in the electronics industry; metal processing; the production of insecticides, herbicides and cleaning detergents, and the manufacture of uranium tetrafluoride used to concentrate the uranium isotope 235 for use as a nuclear fuel (British Geological Survey 2010; Miller 2001). Ceramic grade fluorspar (85-95% CaF2) is used in the ceramic industry as a flux and opacifier in the production of glass and enamels. Ceramic grade fluorspar is also used to make coatings for welding rods and as a flux in the steel industry. Metallurgical grade fluorspar (60-85% CaF2) is primarily used in the steel industry as flux to reduce the melting temperature and remove impurities in steel making. Similarly metallurgical grade fluorspar is also used as flux in cement production to reduce energy consumption (British Geological Survey 2010; Miller 2001)."

Jan 1, 2018