Search Documents

By A. Juganda, Jr. Bogin, J. Brune, J. Grubb, S. Lolon

"Face ignitions at the longwall face are a serious hazard in underground coal operation that can lead to a major mine explosion. Despite having methane monitoring system mounted on the shearer and at various locations on the longwall face, undetected accumulations of methane can still occur and result in face ignitions. With the use of Computational Fluid Dynamics (CFD), the interaction between the air flow at the longwall face and factors that contribute to the accumulation of methane around the longwall face can be modeled and visualized in great detail. The results confirm that the tailgate corner of longwall face is a critical area that is prone to face ignitions and needs to be properly monitored. The occurrence of roof falls on the tailgate entry inby the face and/or poor caving conditions behind the shields can pose a safety risk in the longwall operation. Poor gob caving can lead to insufficient face air quantity to dilute methane at the tailgate corner, while blocking of tailgate by a roof fall can carry methane contaminated air from behind the shields back into the face near the tailgate corner and pull the explosive gas zones (EGZs) inside the gob closer to the face. INTRODUCTION Ignitions of accumulated methane gas at longwall faces are well known to be among the major causes of methane explosion in underground coal longwall mining operations. Some of these ignitions can lead to major mine explosions, such as the Upper Big Branch mine disaster in 2010, in which methane migrated from the gob to the shearer cutting drum where it was ignited, resulting in a major mine disaster (Phillips, 2012). History has shown that, despite having methane monitoring systems mounted on the shearer and various locations at the longwall face and alarms set to 1% CH4 (Mine Safety & Health Administration, 2012), undetected accumulations of explosive methane-air-mixtures can still occur and result in face ignitions. Recent study by Verma and Brune (2016) state that frictional ignitions on longwall faces contributed to 379 incidents or 23% of the total 1,637 cases of face ignitions recorded from 1983 to 2014. The common cause of mine explosions usually involves poorly designed ventilation systems, insufficient ventilation, and inadequate monitoring in critical areas that are prone to methane accumulations. In longwall operation, the tailgate corner of the longwall face can be considered as one such critical area. On-site studies by Krog et al (2006) and Thakur (2008) show that increasing the longwall panel width may also increase cumulative methane emissions at the tailgate. There are also indications that increasing longwall face lengths can result in an increase of the void space behind the face under certain roof conditions (Schatzel et al, 2006). This may cause higher leakage rates from the face to the gob, thus reducing the amount of fresh air available at the tailgate."

Jan 1, 2017

By Hasan Nizamoğlu, M. Deniz Turan, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings (flotation waste) that is formed during copper production may be considered in the class of valuable wastes due to the amount of copper it contains. Owing to the decreasing grade values in copper ores, utilization of wastes such as tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental sense. This study investigated the usage conditions of five different ammonia salts as leaching reactants for the purpose of selective extraction of copper from tailings. For this purpose, the effects of parameters such as leaching temperature and leaching time were examined at different concentrations of ammonium hydroxide, ammonium carbonate, ammonium nitrate, ammonium chloride, and ammonium persulfate. The copper extraction efficiency in the case of using the aforementioned salts by themselves were listed as (NH4)2CO3 (73%) > (NH4)2S2O8 (69%) > NH4OH (64%) > NH4Cl (42%) > NH4NO3 (40%). The highest copper extraction efficiency was obtained in the leaching process that was conducted with the solutions obtained by mixing ammonia salts in the best conditions. Accordingly, as a result of 6 h of leaching at 30 °C in the presence of 22.5% NH4OH and 100 g/L (NH4)2S2O8, 91.47%of the copper was transferred into the

Jun 3, 2020

By J. A. Luppens

Five years ago, Phillips Coal Company decided replacing mainframe/workstation programs with a new package of PC software was clearly the best solution for computer reserve modelling. The system chosen was actually three programs distinguished by their power, cost, flexibility and integration, and ease of learning and use. Phase I involves the use of the "StratiFact" program for borehole data management and seam correlation. This phase is probably the most neglected, yet critical aspect of reserve evaluation. Phase II employs the "PC/Cores" package for modelling and volumetrics. Phase m is "PC-Cut" which provides mine planning tools including an automated cut generator.

Jan 1, 1996

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By G. F. Joklik

Although the mineral shortages of twelve to eighteen months ago have given way to oversupply, their memory lingers on. These problems were man-made: booming demand throughout the industrial world, political and industrial unrest and the oil embargo all contributed. But in the minds of many, the shortages conjured up visions of the depletion of the world's mineral resources, a disaster that could be staved off only by drastic curbs on consumption and therefore, curbs on economic growth. A little historical research shows that fears such as this are not inventions of the 1970's. A hundred years ago, for example, the imminent exhaustion of the world's coal supplies was being predicted in Great Britain. The English economist, John Stuart Mill, who was usually more perceptive, wrote a few years earlier that "it is only in the backward countries of the world that increased production is still an important object". And later there was Franklin Roosevelt who said in 1932, "Our industrial plant is built; the problem just now is whether under existing conditions, it is not overbuilt". His concern, in other words, was not with the discovery and exploitation of new natural resources, but with the administration of known resources and with seeking foreign markets for surplus production. In light of copper prices at the time -- just under 6¢ a pound -- that was understandable. These instances illustrate how, throughout the world's industrial history, concern about surpluses of raw materials has alternated with alarm about the adequacy of supplies and with calls for restricting growth.

Jan 1, 1975

By Q. Dai

In order to float coarse sylvite particles, Potash Corporation of Saskatchewan Inc. (PCS) uses amines and extender oil (Esso 904 oil). Since the content of polycyclic aromatic (PCA) compounds in Esso 904 oil is high, PCS has sought a suitable replacement. Various types of physicochemical tests, including measurements of the electrokinetic potential of emulsified oil droplets, oil/water interfacial tension and wetting of KCl plates by oil, did not provide conclusive results. However, captive bubble contact angle measurements on KCl plates in brine in the presence of flotation agents correlated reasonably with the flotation response. A few non-toxic oils were found to provide good results in the flotation experiments and are now tested under industrial conditions.

Jan 1, 1992

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By M. D. Scott

Lornex Mining Corporation operates an open pit porphyry copper mine in the Highland Valley southwest of Kamloops with a rated capacity of 43 500 TPD (48,000 TPD). It went into production in April 1972. Its concentrator consists of two grinding and flotation circuits in parallel each composed of a 6 000 KW (8,000 HP) 9,75 m (32 foot) diameter by 4,724 m (15'-6") semi-autogenous primary mill feeding two 3 000 KW (4,000 HP) 5,029 m (16.5 foot) diameter by 7,01 m (23 foot) secondary ball mills each feeding a bank of flotation cells. ,The original tailings system picked up the tailings from the flota¬tion circuits in a concrete collection box in the mill and carried the 36% solids density by weight slurry 488 m (1,600LF) through a 1100 mm (42 inch) diameter wood stave pipeline on a .46 percent slope to three 99,06 m (325 foot) diameter center drive thickeners. From the collection box under the thickeners the tailings line con¬sisted of three sections, carrying 50% solids density slurry. The first section consisted of 1460 m (4,800 LF) of 910 mm (36 inch) asbestos cement pipe for gravity flow from the thickener under flow elevation of 1252,4 m (4,109 feet) to the first pump station at elevation 1207,6 m (3,962 feet). Eight concrete drop boxes were used to limit the maximum slope on the pipeline to 0.5 percent.

Jan 1, 1976

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987

By M. Karmis

The design of coal-mine layouts is based on the knowledge of a broad range of geological and geotechnical parameters, which must be determined from a sequence of exploration programs. It follows that any weaknesses in selecting, determining, interpreting or utilizing these data are inevitably reflected into the mine-planning process. In this paper, the main methods of exploration are reviewed and evaluated with the emphasis on acquisition, interpretation and storage of variables pertaining to mine-design. Some common problems are highlighted and recommendations are given for improving the utilization of data and optimizing coal-mine design procedures.

Jan 1, 1980

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992