Search Documents

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By Suprakash Gupta, Pawan Kumar Yadav, Deepak Kumar, Debasis Jana

Draglines are extensively used in Indian mines. A dragline has more than hundreds of components, and it is complex in design. This study involves the evaluation of the reliability of a draglines system using a Bayesian network (BN) model mapped from a fault tree. Based on the BN inference, the reliability estimation, the diagnosis, and the sensitivity analysis are performed. In this paper, the overall reliability of the dragline is estimated as well as the contribution of the subsystems or components in the overall reliability evaluation is presented. The results showed that the three subsystems of the dragline, namely, the dragging mechanism, electrical auxiliary subsystem, and swing mechanism, have the lowest reliability (82.17%, 87.98%, and 91.30%, respectively) after an hour of operation. The overall reliability at the first hour of machine operation is estimated to be 62.03%. The study may provide a reference for future work related to the dragline machine’s reliability design and maintenance.

Jan 14, 2023

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By Rambabu Pothina, MELO EDUARDO PIMENTA DE, Rajive Ganguli

 The mining industry is home to a mass of sensor-generated data that are critical to real-time and long-term optimization. This heavy reliance on sensor data has resulted in an undesirable development. The industry is reluctant to verify the accuracy of sensors as it would mean shutting down important processes. Sensors are typically calibrated once a year, if at all. Errors in sensors go undetected until the next calibration or until errors are so gross as to be obvious

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business' success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed' both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994