Search Documents

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By G. A. Munoz

Gold leaching of an auriferous pyrite ore from the Portovelo deposit in Ecuador indicates that noncyanide leaching systems, such as thiocyanate and thiourea, are not as effective as the traditional cyanide system. For example, whereas approximately 95% of the gold can be leached from the ore with cyanide, only about 50% gold dissolution can be achieved with a thiocyanate leaching system. Electrochemical measurements indicate that gold is not cathodically protected by pyrite in these systems. Based on the results of preliminary diagnostic experiments, it appears that gold dissolution in thiocyanate and thiourea systems is limited by passivation due to the formation of either elemental sulfur or sulfur compounds on the gold surface.

Jan 1, 1999

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By Fabrizio Fara

The Ship Canal Water Quality Project (SCWQP) includes a 2.7-mile long, 18'-10" internal diameter tunnel which is located inWest Seattle. Tunneling in urban areas and soft ground conditions (Till and Till-like soils in Seattle) is associated with the risk of settlements, especially in presence of groundwater above the alignment. The Designer foresaw the use of soil improvement (jet grouting) outside of the launch shaft to mitigate the risk of flowing ground and to provide a redundant sealing. The Contractor proposed and ultimately successfully executed a different approach by using a “Steel Bell System” or Pressurized Can as described in this paper.

Jun 13, 2023

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023

By D. D. Eyer

New or improved technology will continue to drive productivity improvements through the next decade. In January 1988, I presented a paper titled, "Large Underground Mines of the 1990s? before the SME. I will follow some of the themes developed in that paper as modified by our experience in the past two years. In order for a coal company to be profitable today, it has had to reduce unit costs experienced in the past. This is because the current average realization, even accounting for a recent strengthening, remains below that of a few years ago. Doing business as was done in the past is not good enough. The coal industry needs to increase productivity in the range of 5-10% annually merely to stay even with rising costs. Underground productivity has been increasing more rapidly than that for surface mining. With the exception of the Powder River basin of Montana and Wyoming, underground productivity has caught up with that for surface mining in many regions of America. There are a number of technological factors which have attributed to increases in underground productivity and which should be factors in the future.

Jan 1, 1990

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020