Search Documents

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

By Johannes Jäger

"A composite shell lining typically consists of an outer permanent sprayed concrete shell, a water proofing layer and an inner sprayed or cast concrete shell. Composite shell linings become more and more popular and have been built recently on large scale infrastructure projects. Surprisingly there is very little published literature on the actual structural design of composite linings. As a consequence there is a lack of common understanding on how to design a composite lining structure. Composite action of the outer shell (primary lining) initially carrying short term ground loads and the “unloaded” inner shell (secondary lining) require nonlinear concrete modelling to be able to assess the bearing capacity of the composite lining structure adequately. The composite action of the waterproofing membrane and the inner and outer shells can be considered either by simplified closed form solutions or by numerical models. Strength and stiffness parameters of membrane and concrete govern interaction of inner and outer shell. This paper should contribute to understanding composite lining behaviour with focus on the bearing capacity at limit state by taking into account the actual loading history. Possible ways and concepts on how to deal with these topics are presented, however a broader discussion on limit states of the composite lining materials – also in the long term will be required to come to an agreement on composite lining design methodology. INTRODUCTION Composite Lining Technology Traditionally the construction of shotcrete lined tunnels incorporates primary and secondary linings, separated by a sheet or a sprayable waterproofing membrane. The primary lining shotcrete is considered to be structurally temporary and the secondary lining to be permanent, leading to designs which ignore the bearing capacity of the primary lining in permanent condition. There was general perception that the shotcrete lining installed immediately at the tunnel face, experiencing strains up to 1% and even cracking in the early age, combined with mesh reinforcement additional support measures like lattice girder, spiles and bolts cannot be considered as a permanent structure. But also former shotcrete mixes showed significant weakness with respect to durability suggesting a more temporary nature of primary lining shotcrete. On the other hand it was clear that primary lining shotcrete does not disappear, it may lose probably a certain percentage of its bearing capacity, but discounting any contribution from the primary lining at all was considered inherently conservative. There were different strategies to account for the risk of reduced durability and bearing capacity of the primary lining, either by selecting moderate ground loads for the secondary lining design, by assuming that some residual load will be carried by the primary lining. This approach is very much based on experience. Another more rational possibility is to assume that the primary lining degrades into a rocklike material, which is weaker than the primary lining shotcrete but still imparts some strength to the ground around the secondary lining, but does not need to comply with any concrete design codes any more."

Jan 1, 2016

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970's. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended 524 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than one metre in width to pipes with a surface area of 128ha. The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments.

Jan 1, 1984

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By James N. Orlich

Meridian Gold Company's Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984