Search Documents

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By G. Deschenes, W. Yen

Ammonium thiosulphate is a non-cyanide lixiviant for gold leaching. The major problem is the high reagent consumption. A combination of 0.3M (NH4)2S2O3, 0.03M CuSO4, 3M NH3 was used to leach a copper-bearing gold ore at pH 10.2 for 24 hours. 30 kg/t of thiosulphate was consumed. Oxygen and copper species were found to be responsible for thiosulphate decomposition. The thiosulphate consumption could be reduced to around 17 kg/t by adding chelating agent, reducing copper sulphate concentration to 0.001 M and replacing CuSO4 by NiSO4. The increase of pulp density might reduce the thiosulphate consumption to around 17 kg/t. By regulating the oxygen supply, the thiosulphate consumption could be reduced to 10 kg/t.

Jan 1, 2002

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By R. M. Tyson

Sulfides present in the troctolitic and footwall rocks are placed into one of three major zones (hornfels, cloud, and basal) on the basis of their stratigraphic position and mineralogy. Hornfels sulfides, enriched in Fe, represent remobilized sedimentary sulfide. Sulfides from the Cloud Zone are probably magmatic and are enriched in PGE, Cu, Ni, and Ag. The basal sulfides, composing most of the ore, resulted from contamination of the magma by remobilized sedimentary sulfide. The basal sulfides exhibit a differentiation trend in their mineralogy and chemistry. PGE, Cu, and Ag are enriched with increasing differentiation which is attributed to fractionation within an immiscible sulfide liquid.

Jan 1, 1986

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By Roger K. McLimans, Venkatramaiah N. Vasudev, Christian Knudsen, Stefan Bernstein, Dirk Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) analyses of sediment samples from coastal regions of Kerala and Tamil Nadu states and the heavy mineral deposits of Chavara, South India, show large lateral differences in the titanium content in ilmenite due to varying degrees of iron leaching. As the depositional environments for the sands with varying degrees of ilmenite alteration are comparable, the cause for the different degree of alteration is due to differences in the primary source of the ilmenite or to differences in the geochemical history of the ilmenite grains during transport from source to deposit. The CCSEM analyses of the heavy mineral fractions show that source of sediments with a high content of titanium-enriched ilmenites, mainly the heavy mineral deposit around Chavara, resides in the khondalite belt of South India (granulite facies metasediments). The less titanium-enriched ilmenites are sourced from other rocks in the area such as the charnokites. Those conclusions are based on the high MgO content in the leached ilmenites, chemical composition of the accompanying garnets (low CaO and high MgO), and the concentration of aluminum-rich minerals in the sands.

Jan 1, 2005

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

By M. N. Semenoff

On July 8, 1999, EPA announced the RCRA Cleanup Reforms, a set of administrative reforms designed to achieve faster, more efficient cleanups. This paper will discuss the Reforms, the status of their implementation and assess these potential impacts on the mining industry.

Jan 1, 2001

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By S. K. Singh, J. Shepherd

"Feather edging"- a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

The accurate estimation of ore reserves along with capital and operating costs are two key components to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by improper estimation of ore reserves. The accurate estimation of ore reserves for any deposit relies heavily on understanding its geology and underlying assumptions unique to the estimation techniques being used. The assumptions unique to commonly used traditional and geostatistical reserve estimation technique will be reviewed. The shortcomings of the estimation techniques and their possible impact on a given project's economic outcome will be discussed. The latest developments in geostatistics in overcoming existing reserve estimation problems will be presented.

Jan 1, 1994

By Joseph P. Gildner, Michael S. Kucker, Robert A. Robinson

Considerable controversy seems to exist over the extent and nature of information that should be provided in design-build type contracts. Much of this controversy may relate to the types of owners, ranging from private industry to state and federal agencies that are implementing design-build. Philosophies for the development of geotechnical information ranges from no information to a thorough investigation approaching that needed for final design. Several recent projects, such as the Channel Tunnel in Europe, Whittier Tunnel in Alaska, Tren Urbano in Puerto Rico, and Sound Transit in Seattle have taken varying approaches to providing and interpreting geotechnical information for bidders. The pros and cons of these various methods are discussed and assessed.

Jan 1, 2001

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By G. W. Toth

The coal mining cost models described in this paper represent a computerized estimating procedure for analyzing mining costs and requirements of proposed coal mining projects. Both surface and underground mining analyses can be conducted through the use of these models. These models were developed by the NUS Corporation for the Electric Power Research Institute (EPRI). The methodology design of the cost models follows a process engineering approach for determining mining requirements and costs similar to the logic typically employed in preliminary mine feasibility studies. All capital and operating costs associated with a new coal mining project are thereby estimated. The results of these analyses are then entered into a financial analysis framework which computes annual cash flow summaries, utilizing a profit and loss statement approach, to solve for either the coal value/ton (minimum required selling price) or the rate of return on equity for the project. The coal value/ton is also referred to as the economic cost of production (F .O . B. mine, including preparation).

Jan 1, 1980

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026