Search Documents

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

Records over the past ten years indicate that there is potential for serious multiple accidents due to engulfing associated with rockpasses. Significant attention is not usually given to the design of rockpasses, with the implication that mistakes leading to poor performance of the passes are often repeated. This paper outlines general guidelines for the design, support, operation and rehabilitation of rockpasses based on information obtained from the limited amount of literature on the subject.

Jan 1, 2005

By U. Kumar

Product designed characteristics like reliability and maintainability affect maintenance cost, service performance, and therefore product support strategy must be defined during design stage in terms of these two dimensions. Furthermore product support and service delivery strategy has considerable influence on the total life cycle cost and the economic viability of industrial systems/products. he paper presents a concept for the development of service delivery strategy for industrial products with a special reference to mining systems. In this paper we emphasize that the strategy for product support should not be centred only on ‘product’ but it should also take into account the service delivery capability of the manufacturers/suppliers and users service organization, users competence and capability, product use location, logistics and infrastructures, etc., to arrive at the best performance and economic results. Such strategy should invariably include services supporting the client apart from considering services supporting the product. The discussion in the paper is based on the experiences from the manufacturing industry engaged in manufacturing of mining systems and the observed trends in technology and management of operation and maintenance of mining systems. Keywords: Maintenance and product support, Service supporting client, Service delivery strategy, Products reliability and maintainability, Product use location, Operating environment, etc.

Jan 1, 2003

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

By Sverre Olsen, Kai Tang

The composition of ferromanganese slag is very important as it determines the slag/metal equilibrium relations including MnO content of final slag, melting relations and slag viscosity. The slag composition is further expected to influence the process temperature. The properties of ferromanganese slags are suitably described by its basicity and A/S mass ratios. The influence of slag basicity has been discussed in the previous papers. The present paper will discuss the effect of Al2O3 on melting relations, viscosity and MnO-content of final slag. This discussion will be based on assessed thermochemical databases and a recently developed viscosity model.

Jan 1, 2007

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By B. Elevli

The aim of this paper is to demonstrate the implementation of multicriteria analysis in selection of the most suitable underground ore transport system for a chromite mine in Turkey. The related problem includes five possible ore transport systems and six criteria to evaluate them. The adopted evaluation and ranking method for this study is PROMETHEE. PROMETHEE I revealed a partial order of alternatives where incomparability exists. PROMETHEE II gave the absolute ordering of alternatives. The results have shown that the PROMETHEE method can be successfully used in solving mining engineering problems. Keywords: multi-objective, decision analysis, mining, ore transport system

Jan 1, 2004

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By K. Sørli, H. Elstad, I. M. Skaar, A. Hildal

Generally, monitoring of refractory furnace linings is of interest to the metallurgical industry. The main issues are to control wear of the furnace lining and break out of molten metal. Penetration of molten metal through the lining can cause considerable damage to equipment in the vicinity of the furnace and endanger operators. Rebuilding of a furnace lining is expensive, mainly because it stops production, but also because the lining materials are expensive. Here, two methods for monitoring the lining of a smelting furnace are presented. The methods are based on monitoring of the temperature distribution in the lining, more specific monitoring an isotherm in the lining. One method is based on the assumption of unidirectional heat flow locally, reducing the problem to a set of one-dimensional heat conduction problems. The other method is based on inverse heat conduction. In this context inverse heat conduction means estimating the wear from temperature measurements using mathematical optimization techniques. The study is based on the ilmenite smelting furnace at Tinfos Titan & Iron KS. Some results from real temperature measurements and real observations from the ilmenite smelting furnaces is presented.

Jan 1, 2003

By J. G. Bruwer

Paper written on project work carried out in partial fulfilment of B Eng Met Surface coatings persisting on zircon particles, after being leached in an acidic solution, are believed to be the cause of zircon misplacement during the electrostatic separation of heavy mineral beach sands. Electrostatic separation is employed to separate non-conductive zircon particles from more conductive rutile particles. Surface coatings on zircon particles are believed to render the non-conductive zircon particles more conductive, resulting in the contamination of the more conductive rutile stream with zircon particles. Resistivity measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed to compare the surface characteristics of zircon particles found in the different product streams following electrostatic separation. XPS analysis showed that no significant difference exists in the outermost layer of the zircon particles found in the different streams. SEM analysis showed the existing surface coatings on zircon particles from different product streams to have similar chemical compositions. Resistivity measurements confirmed the results obtained from both the XPS and SEM analysis; no significant differences in the resitivities were observed. From the results obtained it suggests that surface coatings present on zircon particles are unlikely the primary cause of zircon misplacement. Zircon losses can possibly be a result of machine related aspects. Key words: XPS; SEM; resistivity measurements; electrostatic separation; heavy mineral sands.

Jan 1, 2007

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By G. Hangone

Paper written on project work carried out in partial fulfilment of MSc thesis This paper investigates the effects of thiol collectors: xanthates, dithiophosphates, dithiocarbamates and mixtures of these on the froth flotation performance obtained with a bornite-rich copper sulphide ore from Okiep Copper Mine with a feed grade of 1.8%copper. Batch flotation tests were used to assess the performance in terms of mass-water recovery, sulphur grade-recovery and copper grade-recovery relationships and the Klimpel rate constant for copper recovery. The results showed that the di-ethyl-dithiocar-bamate (di C2-DTC) was the weakest collector of copper sulphide minerals. Highest copper recoveries were obtained with the di-ethyl-dithiophosphate (di C2-DTP), which were accompanied with more watery froths and lower copper grades demonstrating frothing properties in addition to collector action. Superior copper recoveries were obtained with the 90% ethyl xanthate (C2-X):10% di-ethyl-dithiophosphate (di C2-DTP) and 90% ethyl xanthate (C2-X):10%di-ethyl-dithiocarbamate (di C2-DTC) collector mixtures compared to that obtained with ethyl xanthate at an equivalent collector dosage of 0.139 mol/ton ore (a dosage equivalent to 20 g sodium ethyl xanthate per ton ore). A superior copper grade was obtained with the 90% ethyl xanthate: 10% di-ethyl-dithiocarbamate collector mixture at a dosage of 0.0695 mol/ton ore compared to that obtained with ethyl xanthate at the same equivalent dosage. Keywords: flotation, collector mixtures, copper sulphide ore

Jan 1, 2005

By M. F. Wells

The method used to salvage South Deep?s Main Shaft after it was flooded by an inrush of water at about 450 m below collar on 1 May1996 is described. The individual techniques employed in the salvage were all proven technology, but the combination in which they were applied is considered to be novel. The operation involved the following activities in order of occurrence. ?the dewatering of the shaft with submersible pumps ?the placement of a French drain on the shaft bottom muck pile ?the positioning of large diameter heavy walled draft tubes, and smaller tightening up, grout intrusion and reverse flow pipes ?the casting and curing of a structural concrete plug; the capping of the draft tubes; the intrusion of several thousand tons of cement grout into the aquifer by pressure induced reverse flow ?the sealing of the aquifer ?extensive probe drilling and sealing of the zone around the inrush point with cement and other specialized grouts ?the mining out of the plug and the re-establishment of normal sinking routines.

Jan 1, 1999

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009