Search Documents

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

Phase equilibria have been determined experimentally for pseudo-ternary sections of the form ?MnO?-(CaO+MgO)-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.17 and MgO/CaO weight ratios of 0.25 and 0.17 respectively for temperatures in the range 1473-1673 K. The primary phase fields present for the MgO/CaO weight ratio of 0.17 include manganosite (Mn,Mg,Ca)O; dicalcium silicate a-2(Ca,Mg,Mn)O?SiO2; merwinite 3CaO·(Mg,Mn)O·2SiO2; wollastonite [(Ca,Mg,Mn)O?SiO2]; diopside [(CaO,MgO,MnO,Al2O3)?SiO2]; tridymite (SiO2); tephroite [2(Mn,Mg)O?SiO2]; rhodonite [(Mn,Mg)O?SiO2] and melilite [2CaO?(MgO,MnO,Al2O3)?2(SiO2,Al2O3)]. For the section with MgO/CaO weight ratio of 0.25 the anorthite phase (CaO·Al2O3·2SiO2) is also present. The liquidus temperatures of ferro- and silico-manganese smelting slags have been determined. The liquidus temperatures at low MnO concentrations are shown to be principally dependent on the modified basicity weight ratio (CaO+MgO)/(SiO2+Al2O3).

Jan 1, 2004

By J. J. Geldenhuys

A colloquium on &apos;Developments in the Mechanization of Mining Operations&apos; was held in, conjunction with the 1984 Electra Mining Exhibition, at the Milpark Holiday Inn in Johannesburg on 19th September, 1984. An attendance of close on 200 delegates was testimony to the popularity of the subject. The delegates included a number of visitors from abroad, including senior members of the management of foreign companies and a member of the Council of the Institution of Mining and Metallurgy, United Kingdom. Both the local and foreign press was also represented.

Jan 1, 1985

By G. T. van Rooyen

The susceptibility of a low-alloy steel that has been hardened and tempered-826 M40 (EN26)-to embrittlement by strain aging during service was simulated by artificial aging of specimens at 100°C. It was found that the brittle transition temperature of both monotonic and cyclically strained material was increased by only about 25°C as a result of strain aging. It is concluded that the susceptibility of low-alloy steels in the hardened, tempered condition is less than that of low-carbon steel, and that such steels qualify for exemption of the periodic &apos;annealing&apos; required by the Mines and Works Act.

Jan 1, 1986

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001