Search Documents

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

By C. A. Young, J. L. Bowden

"Cyclic voltammetry experiments were conducted on copper and chalcopyrite (CuFeS2) in the absence and presence of ethyl xanthate, and compared to mass-balanced EH–pH diagrams. The results for copper duplicate those found in the literature and confirm xanthate chemisorption. However, the, results indicate that chalcopyrite oxidizes to chalcocite (Cu2S) and only afterwards is chemisorption observed due to small currents appearing with xanthate. This phenomenon suggests that the mineral's hydrophobicity is induced by more than dixanthogen and copper xanthate. Hydrophobicity was found to be pH-dependent over a range of alkaline conditions (pH 7–11) at narrow potentials (0 to –200 mV). An EH–pH diagram for chalcopyrite with xanthate is presented to illustrate the conditions under which chalcopyrite would be hydrophobic and thereby more thoroughly explain the results in the literature. IntroductionSulphide minerals are generally concentrated from ores by froth flotation, a physiochemical process that induces separation based on differences in hydrophobicity. In this process, a gas is bubbled into a slurry and the minerals that are hydrophobic (water-repelling) adhere to the bubbles and float to the surface while the hydrophilic (water-loving) minerals remain in the slurry. With sulphide minerals, the hydrophobicity is generally established in two ways. The first is by the addition of a collector, which is a heteropolar molecule with a reactive inorganic head group and an inert organic tail. Typically, the head group bonds with the sulphide mineral surface by adsorbtion either chemically (chemisorption) or physically (physisorption) or by complexing with atoms that solubilize somewhat at the surface (surface precipitation). These interactions leave the organic tail protruding from the mineral surface, thereby inducing hydrophobicity. The second method is by oxidation of the mineral surface to form a layer that is metal-deficient/sulphide-rich or comprised of elemental sulphur. Because the layer mimics naturally hydrophobic sulphur, this enables ‘collectorless’ flotation. Furthermore, this oxidation phenomenon adds an electrochemical dimension to the understanding of sulphide mineral flotation."

Jan 1, 2016

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By A. Pytlik, W. Masny

"Underground mining is subject to various natural hazards such as seismic events, rockbursts, fire, and gas (methane). In general, an increase in the extraction depth causes an increase in the likelihood of these hazards, especially seismic activity and rockbursts. Dynamic phenomena such as rockbursts and tremors have been recorded on six continents: Europe (Poland, Russia, Czech Republic, Germany, and Slovenia), Asia (India, and China), North and South America (USA, Canada, and Chile), Africa (South Africa), and Australia. To select appropriate mine working supports for such dynamic phenomena, the performance characteristics of such support types must be determined under both static and dynamic load conditions.This article presents information regarding the application of rockbolts in Polish underground hard-coal mines. Dynamic phenomena occurring in the mines from 2004–2013 are also characterized. A methodology developed at the Central Mining Institute (GIG) for the laboratory testing of rockbolts is presented. In this methodology, the bolts are loaded by the direct impact of a free-moving mass (up to 20 000 kg) at speeds of up to 1.2 m/s. The facilities at GIG used to test the support under static and dynamic load conditions are characterized, and the results of laboratory tests on yielding bolts with a nominal capacity of 420 kN are presented. These types of bolts are commonly used for reinforcing steel arches and the surrounding rock mass in Polish coal mines. The results of the laboratory testing of yielding bolts are discussed.IntroductionSeismic events such as rock bumps and tremors occur with great frequency during underground mining. These phenomena have been reported in such countries as Poland, Czech Republic, Germany, France, Slovenia, Russia, India, China, the USA, Canada, Chile, South Africa, and Australia (Brauner, 1991; Potvin, Hudyma, and Jewell, 2000; Kidybin??ski, 2003; Driad-Lebeau et al., 2005; Li, Cai, and Cai, 2007; Whyatt and Loken, 2009; Durrheim and Riemer, 2012; Holub, Rušajova, and Holec?ko, 2011). Descriptions of the dynamic events and their effects in the form of damage to or destruction of supports have been presented in many publications, both for hardrock mines as well as for coal mines (Brauner, 1991; Dubin??ski and Konopko, 2000; Heal, 2010; Heal and Potvin, 2007; Simser, Joughin, and Ortlepp, 2002; Kaiser and Cai, 2012; Cai 2013; Nierobisz, 2013; Mark, 2014; Masny and Prusek, 2015). One of the main goals of the research has been to develop methods, criteria, and guidelines for the selection of an optimal and safe support for mine workings located in areas of rock bumps or tremors. Example of such studies include the Canadian Rockburst Support Handbook (Kaiser, McCreath, and Tannant, 1996), or the principles presented in the literature (Li, 2010; Cai, 2013)."

Jan 1, 2016

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By B. Kweto, W. Legodi, C. van Buuren, R. F. Sandenbergh

Biooxidation, and especially the BIOX® process, is a viable, economical and environmentally attractive process to liberate gold hosted in refractory sulfides by oxidatively leaching the sulfides as soluble sulfates. The moderate to high cyanide consumption during the subsequent cyanidiation of the washed biooxidation residue is probably caused by the retention on the solids of labile sulfur species formed during the multi-electron oxidation process of sulfide to sulfate. In this work the nature and mode of transport of the cyanicides in the products from the mesophile BIOX® process, as well as that of the combined mesophile and thermophile bioxidation process, were considered and strategies to reduce cyanide consumption evaluated. It was found that labile sulfur species were the major cyanide consumers in the mesophile biooxidation product, forming predominantly thiocyanate during cyanidation. The transfer of labile sulfur species was only marginally decreased by more intensive and thorough washing of the biooxidation products with warm and hot water, intense stirring and warm caustic leaching. A major reduction in cyanide consumption was however achieved by using a combined mesophile and thermophile biooxidation process. Keywords: Biooxidation, refractory sulfide gold ores, cyanide consumption

Jan 1, 2020

By Z. Bibak and S. Banisi

Granular systems, i.e. particles with realistic shapes, are commonly encountered in nature and industry. While the discrete element method (DEM) is a tool for the simulation of granular flow, in most of the DEM simulation particles are assumed to be spherical. It is questionable whether results drawn from a spherical particle could be easily transferred to a non-spherical particle. Thus, obtaining a fundamental understanding of the underlying physics of granular flows is not only of academic interest, but is also highly related to industrial applications. An in-house developed DEM software called KMPCDEM ©, which was coded to handle non-spherical particles, was used to simulate the particle behaviour. In this paper, the effect of particle shape on the dynamics of particles of non-spherical and spherical shape, including algorithms for the determination of the particle orientation, the moment of inertia, shape representation, and computation time was described. The assumption of a spherical shape has been justified by the complexity of simulation and significantly higher computation time if a realistic shape for particles was used. Dynamics differences showed that findings obtained from spherical particle systems could not be readily extrapolated to non-spherical particle systems. Consequently, particle shape is an important, if not even the most important parameter to be considered in DEM simulations, and therefore has to be captured accurately if DEM is to be used as a predictive tool. Keywords: Discrete element method (DEM), granular systems, non-spherical particles

Jan 1, 2020

By F. Nakhaei, Z. Pourkarimi

Tailings produced from the iron ore industry present many challenges due to the high economic and environmental impacts involved with their disposal. However, the relative scarcity of high-grade iron ores has driven manufacturers to recover and recycle these valuable tailings (secondary sources). This study aimed at the purification of ultrafine tailings with high sulphur content from an iron ore concentrator via reverse flotation to produce pellet feed fines. A specially designed flotation column featured with a nano bubble generator and a conventional bubble generator were employed to assess the effects of nano bubbles on the desulfurisation performance of iron ore concentrate under different operating conditions. Results obtained from this study indicated that the sulphur content of iron concentrate could be reduced from 1.2% to 0.22% in the presence of nano bubbles. Also, the results showed that use of nano-micro bubbles increased sulphur recovery 20% more, in comparison to micro bubbles. Keywords: Column flotation, iron ore, tailings, slime, nano bubbles, desulphurisation

Jan 1, 2020

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By S. Krishnannair

Singular Spectrum Analysis (SSA) is an effective data-adaptive multimodal tool for monitoring chemical processes. However, monitoring multiscale signals using principal component analysis obtained from the multilevel decomposition of process signals using basic SSA assume the upper control limits of monitoring charts (" ) to have a Gaussian distribution. This assumption deteriorates the performance of basic SSA when applied to the monitoring of nonlinear processes. To address the issue in this paper, the kernel density estimation (KDE) was used to estimate upper control limits of monitoring charts for basic SSA based nonlinear process monitoring techniques. The monitoring performance of the resulting basic SSA-KDE approach was then compared with a basic SSA approach of which upper control limits of the monitoring charts were determined based on a Gaussian distribution. Application on nonlinear dynamic simulated process and base metal flotation plant chemical processes showed that the SSA-KDE approach provided better overall performance than the SSA approach with Gaussian assumption-based upper control limits for its monitoring charts. Keywords: Fault detection, singular value decomposition, singular spectrum analysis, kernel density estimation

Jan 1, 2020

"Chairman: Professor B. W. MacKenzieRapporteur: Professor D. A. PretoriusPapers:Optimum spacing for soil sample traverses by W. A. HodgsonEvaluation of geochemical data by C. J. LenzResearch in oil exploration decision-making by J. W. Harbaugh and A. Prelat A drill hole data bank by M. R. AndertonOre reserve estimation and depletion planning for a beach diamond deposit by M. M. OosterveldIn opening the session, the Chairman indicated that the papers and discussions would revolve about quantitative methods of analysis and optimization of various aspects of exploration planning. The five papers would cover a wide range of topics within a general theme of exploration analysis, and it would be appropriate, therefore, to present the. papers as representing a sequential information-gathering process, namely, (i)geochemical and geophysical types of surveying for the location and identification of anomalous zones, (ii) tren¬ching and drilling of the anomalous zones found, and (iii) further refinement of the data for ore reserve calculations and production planning.The first paper, which was presented by Dr W. A. Hodgson, dealt with the optimum spacing between soil sample traverses conducted during geochemical prospecting. The theme of the paper was that the critical sampling interval should be based on the concept of element continuity, and that this interval could be determined by means of a correlogram. Ensuing discussion concerned the probability of the method, designed for areas where dispersion was high, working in localities where dispersion was either low or virtually non-existent. In the latter eases, specific orientation surveys for varying topographic, climatic and geological conditions would possibly be more useful than the preparation of correlograms. A further suggestion was made that cost versus risk should be taken into consideration when deciding upon the spacing between traverses. A balance could be struck by mathematical optimization. If the exploration budget was fixed, then the variance of risk could be minimized.The second paper was a short contribution by Mr C. J. Lenz. Computer-based plotting and evaluation of geochemical prospecting results were carried out because the low cost of analysis in Rhodesia permitted very large volumes of data to be accumulated in mass-coverage operations. Anomalous areas were demarcated within different environments by selecting probability or population boundary values from frequency distributions. In the short discussion which took place it was debated whether the method should be used only in the early high-risk stages of geochemical exploration and whether the introduction of geological bias could influence the actual results of an exploration program."

Jan 1, 2014

By C. H. Johannes, N. B. Strydom, C. H. Van Graan, J. G. A. Van Heerden

Note: The practical application of microclimate cooling in an underground stope in a gold mine by C. H. JOHANNES, C. H. VAN GRAAN, N. B. STRYDOM and J. G. A. VAN HEERDEN INTRODUCTION Although much information was available on the use of pre-frozen jackets as micro climate coolers in underground situations!, 2, no information was available on their performance under practical conditions in stopes. The objectives of this study were. O.F .S. Branch Minutes of the General Meeting held in the upstairs lounge at the Harmony Country Club, Harmony G.M. Co. limited, on Wednesday 12th November, 1975 at 4.00 p.m. NIM reports Report no. 343 A mineralogical investigation of gold-bearing sulphidic ore from the Florence-Devonian Mine, Barberton.(20th May, 1968; re-issued Dec. 1975). Report no. 1384 . Flotation tests on samples of Canadian copper-zinc ores. (12th Nov., 1971; re-issued Nov. 1975). The results are given of laboratory Report no. 1488 Extraction of rutile from Highveld smelter slags. (28th Sep., 1972; re. issued Nov., 1975). Report no. 1499 The production of medium -carbon ferrochromi'um. (4th Dec., 1972; reissued Nov. 1975). Report no. 1521 The dissipation of electrical power in the burden of a submerged-arc furnace. (15th Feb., 1973; re-issued Nov. 1975). Report no. 1527 The physicochemical properties of slags associated with the smelting of nickel sulphide concentrates. (21st Feb., 1973; re-issued Nov. 1975). Report no. 1544 The recovery of salable ferrochromium from material discarded by Ferrometals Limited. (11th Jun., 1973; re-issued Nov. 1975). Report no. 1547 Physicochemical and thermodynamic properties of slags in the system MgO-AlOl.5SiO2. (23rd Aug., 1973; re-issued Nov. 1975). Report no. 1548 Physicochemical properties of slags in the system MgO-Al2O3-SiO2 and their application to the technology of ferro-alloy smelting. (13th Jul., 1973; re-issued Nov. 1975). Report no. 1553 Characterization of the flotation properties of fluorspar from smallscale batch and pilotplant tests. (27th Sep., 1973; re-issued Nov. 1975). Report no. 1555 The analysis, by atomic-absorption spectrophotometry, of matte-leach residues. (2nd Oct., 1973; re-issued Nov. 1975). Report no. 1590 The separation of osmium from ruthenium in hydrochloric acid solutions. (18th Jan., 1974; re-issued Oct. 1975.) Report no. 1606 The electrical-resistance characteristics of the charge in the electric reduction furnace. (1st Feb., 1974; re-issued Oct. 1975). Report no. 1622 The electrical conductivity of the charge in a ferrosilicon furnace. (2nd Apr., 1974; reissued Oct. 1975).

Jan 3, 1976

By A. W. S. Schumann

A. W. S. Schumann The first reason for todays success lies in the very high standard which was set by our speakers today and I think that we owe a very special vote of thanks to Messrs P. M. C. Wilson, A. A. Oakes, M. J. Deats, A. C. Coetzee, R. E. Burnton and J. G. Ferguson. This, however, cannot account for the fact that there was a tremendous response even before anyone knew who was going to speak or what they were going to speak about. I suggest that the response was enthusiastic because people expected a more informal gathering with a greater opportunity for feedback, for an exchange of views and for questions and answers. The very popularity of the idea has defeated its own ends to some extent. This gathering is too big and many people must have been left with questions unanswered. Possibly one should arrange for a number of meeting places-there are many in the Chamber and the surrounding mining houses-and then have separate meetings in the morning with joint reporting session in the afternoon. Alternatively, we could have a symposium after the colloquium, using Webster's definition of a symposium as as 'a drinking party of merry fellows'. We all know that it is easy to discuss mining into the small hours. Obviously one cannot summarise todays papers and discussions, but I would like to make a few comments on technical matters and after that I would like to speak for a moment about what I see as major trends or tendencies which arise from discussions of this nature. Regarding the question of placing a village on a mine or away from a mine, I would mention that there is quite a body of literature on the adverse sociological effects on the development of children in any community in which the great majority of parents share the same occupation. It is something to be avoided if possible. We discussed the concept of the moving stockpile. If this is proved to be successful, it could save a considerable amount of money for Escom who could then avoid the construction of very large and costly staithes which are now regarded as parts of power stations. One does not see why both a moving stockpile and a staith should be necessary. By the way, speaking of Escom, I see that Mr Bob Scott is here; he has stopped pulling my leg by saying that we sell stone to Escom; perhaps someone has told him that if this is true, it must be the cheapest stone you can buy in this country. My next point relates to the use of epidiascope. It struck me again that this instrument which provides a visual image to accompany your message, can be very effective if it is properly used. These papers speak of a great deal of hard work which went into their preparation, and one really feels that the authors should have taken a few minutes more to prepare their drawings specifically for the epidiascope. There should be nothing on the drawing which is not necessary to illustrate a particular point and there should be nothing on the drawing which is not visible from the back of the hall. In particular, if one cannot read the figures along the sides, then one

By M. A. Belokrys, F. O. Milovich, D. D. Aksenova, V. A. Ignatkina, V. A. Bocharov, A. A. Kayumov

Copper remains one of the most sought-after metals in the industry. Tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that occur in pyrite copper, copper-zinc and polymetallic ores are an additional reserve for increasing technological parameters of flotation. Pyrite mass (85% and more) has similar flotation properties to other sulfide minerals, and imperfection of reagent regime is a common problem that occurs during quality copper concentrate processing. Due to tennantite's and chalcopyrite's differences in flotation properties with butyl xanthate at pH > 10, tennantite often reports to the flotation tails. Hight alkalinity of the medium increases the oxidation level of sulfide minerals, thus increasing the concentration of S2O3 2-, SO3 2- SO4 2-. At processing facilities in the Russian Federation, the concentration of thiosulfate ions in pulp is in the range of 0.5 to 1.5 g/l and higher, which leads to a decrease in flotation activity of the tennantite. The effect of butyl xanthate (as standard), thionocarbamate, dithiophosphate and M-TF (a mixture of dithiophosphate and thionocarbamate) on monomineral (tennantite and pyrite) flotation in the presence of sodium thiosulfate was studied. The variable parameters of the "thiosulfate-collector" flotation complex were thiosulfate concentration (100-900); pH (8-12,5). The scientific methods included contact angle for hydration assessment; TEM for surface studies; UV spectroscopy and iodometric titration for solubility control. Comprehensive studies have established a connection between the concentration of thiosulfate ions and tennantite flotation selectivity. Flotation activity of tennantite is higher at pH 8 with a thiosulfate concentration under 300 mg/l. Pyrite remains active with butyl xanthate under the same conditions. TEM images of the surface films of the collectors on pyrite were acquired at pH 8. The MTF provides the biggest difference in adsorption, wettability and flotation activity between tennantite and pyrite at pH 8 and thiosulfate concentration under 300 mg/l, in comparison with butyl xanthate. The results of the research will be applied to improve selective reagent regimes of tennantite minerals flotation. Keywords: Tennantite, pyrite, chalcopyrite, sphalerite, flotation, sulfhydryl collectors, thiosulfate, adsorption, mechanism, reagent regime

Jan 1, 2020

By J. E. Quintanilha de Menezes, L. Ribeiro e Sousa, I. Ferreira

The Paradela dam has a spillway that makes it possible to discharge a maximum flow of 400 m3/s, the water discharges being on the river Sela, about 2km upstream the river Cávado. After the first use of the spillway, some landslides have occurred on the right bank of the river Sela as a result of the erosion generated on its base about one hundred meters near some houses of a small village. This paper presents a study performed for the slope stability where finite element results are taken into account. A monitoring program was established that essentially consisted of measuring sub-horizontal displacements in points located in boreholes at different depths and also phreatic levels. Some monitoring results are presented. Le barrage de Paradela a une décharge d’eau avec un débit maximal de 400 m3/s sur le fleuve Sela dans un endroit situé environ 2km sur l'amont du fleuve Cávado. Après la première utilisation de cette décharge, quelques glissements se sont vérifiés sur le versant droit du fleuve Sela résultant de l’érosion générée sur sa base dans une zone à 100 mètres de quelques maisons d’un petit village. Ce travail présente une étude réalisée concernant la stabilité du versant avec la considération des résultats des éléments finis. Un programme d’auscultation a été mis en place pour mesurer les déplacements sub-horizontales sur des points situés en forages à des différentes profondeurs. Quelques résultats de cette monitorization sont présentés. Der Ueberlauf des Padela Dammes ermoeglicht das Ablassen einer max. Wassermenge on 400 m3/s in den Sela Fluss, ca. 2 km flussaufwaerts des Cávado Flusses. Nach Inbetriebnahme des Ueberlaufes traten in ca. hundert Meter Entfernung zur Wohnbebauung eine Dorfes Erdrutschungen am rechten Ufer des Sela Flusses auf, die auf Erosionen am Flussbett zurückzuführen waren. In der vorliegenden Studie wurde die Boeschungsstabilitaet unter Beruecksichtigung von Berechnungsergebnissen der Finiten Element Methode untersucht. Es wurde ein essprogramm ausgearbeiten, das im Wesentlichen auf Messungen der Untergrundverformungen in verschiedenen Bohrlochteufen sowie auf Grundwassermessungen beruht. Im Folgenden sind einige Messergebnisse dargestellt.

Jan 1, 2003

By S. Vorberg, B. Fischer, U. Glatzel, R. Völkl, D. Lupton, M. Wenderoth

Owing to their excellent oxidation and corrosion resistance, Pt and its alloys are being used preferentially at elevated temperatures and in aggressive environments. For example, an important application field is the glass industry. Alongside the discovery of new potential application fields, the knowledge of material properties is essential for computer simulations, design configuration, process optimization, research and development or quality assurance purposes. Due to the importance for technical applications high-temperature properties have been investigated for currently available Pt-base alloys with ongoing improvements. For the determination of tensile creep test data up to 3000°C, including precise strain measurement, special experimental equipment has been developed at the University of Applied Sciences Jena, Germany. An overview of the existing and newly obtained mechanical property data on pure Pt, solid-solution strengthened Pt-Rh alloy, oxide dispersion-hardened materials Pt DPH and Pt 10%RhDPH as well as cutting-edge results on Pt-base superalloys hardened by intermetallic precipitates will be presented and discussed. Furthermore, some important application examples for the abovementioned Pt-materials will be given.

Jan 1, 2006

By P. R. Jochens, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace by A. A. HEJJA,D. D. HOWAT, andP.R.jOCHENS Published in the Journal March 1973. DISCUSSION R. E. Leyman* The authors discuss in detail the effects of transport and storage at the steel plant on the reactivity of lime as measured by the DIN Reactivity Test. They attribute the deterioration in reactivity to the absorption of water vapour and carbon dioxide, but make no mention of the possible role of atmospheric sulphur dioxide in this respect. The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E FEATHER and G. M. KOEN Published in the Journal February 1973. AUTHORS' REPLY TO DISCUSSION (Published in the Journal July 1973) H. P. Carlisle Mr Carlisle's questions and observations will be dealt with in the same order as they were raised. 1. How were the mass percentages of the grains determined from the sizes measured in polished section?

Jan 3, 1973