Search Documents

Minutes of the Annual General Meeting Held at Harmony Country Club on Wednesday, 2nd August, 1978, at 7.30 p.m. Mr A. N. Shand (Chairman of the O.F.S. and Klerksdorp Branch) was in the Chair. Also present were:.... Induction of Chairman Mr A. N. Shand introduced Mr H. M. W. Eschenburg by briefly outlining his past career and achievements, and, in calling upon him to take the Chair, wished him a very successful year of office..... Address by the President of the S.A.I.M.M. The Chairman introduced Mr Von Wielligh by outlining his career and achievements. After completing his education, he joined J.C.I. in 1936 as a sampler, and from that time served the company in many capacities, culminating with his appointment to the Board in 1974.....

Jan 1, 1979

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

Historical Background. South Africa's industrial history began with the discovery of gold and diamonds during the last century, and the mining industry was the first chief component of our technological development. During the past six decades, quantum leaps were made in other fields, too, when other industries and research bodies such as Escom, NDC, Iscor, Sasol, Foskor, Alusaf, Mintek, cs I R, SA B S, and A E C were established. These meaningful additions have two outstanding characteristics. Firstly, they were linked mainly to primary activities such as energy and minerals and, secondly, their establishment was to a large extent due to the driving force of individuals such as Van der Bijl, Van Eck, Rossouw, Schonland, and Roux, rather than to impersonal government policy. Encouraging signs of the evolution of such policy has emerged during the past few years.

Jan 1, 1989

I. Book review Legal and institutional arrangements in minerals development. Edited proceedings of a workshop organized jointly by the VN. Department of Technical Co-operation for Development and the German Foundation for International Development (DSE), held in Berlin in August 1980. London, Mining Journal Books, 1982. Soft, 228 X 149 mm, xi + 223 pp. Approx. R30 + GST. Reviewer: M. J. Martinson 2. New books Strength of metals and alloys (IOSMA 6). R. C. Gifkins (Editor). New York, Pergamon, 1982. Approx. 1200 pp. 3 vols. V.S. $220. Deformation-mechanism maps. The plasticity and creep of metals and ceramics. H. J. Frost and M. F. Ashby. New York, Pergamon, 1982. Approx. 250 pp. V.S. $60. Pressure diecasting, Part 2. The technology of the casting and the die. D. F. Allsop and D. Kennedy. New York, Pergamon, 1982. $ V.S. 27.50.

Jan 1, 1982

By O. A. W. Strydom, J. C. M. Wethmar, P. R. Jochens, D. D. Howat

Liquidus temperatures in the Cr-Fe-Si system in the composition range representative of ferrochromium-silicide produced in South Africa J. C. M. Wethmar, B.Se. (Eng.) Rand D. D. Howat,U B.Se. (Glas.), Ph.D.. F.I.M. P. R. Joehens, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. O. A. W. Strydom, M.Sc., Ph.D. Alloys in the composition range of chromium, 20 to 50 per cent, iron, 10 to 30 per cent, and silicon, 25 to 55 per cent, were subjected to both differential thermal analysis and the classical quench method so that the liquidus temperatures of ferrochromium-silicide alloys could be determined. The results are presented as liquidus curves on pseudo-binary sections at various ratios of chromium to iron and as liquidus isotherms in the ternary section.

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By S. T. L. Harrison, J. R. Amaral Filho, M. Smart, J. Broadhurst, J. Weiler

Technosol production from mine waste, following amendment with additional organic residues, to provide healthy and functional topsoil is an advantageous alternative to the long-term dump disposal of mine waste. Minimising the legacy of mine waste and supplying soil for mine site rehabilitation contributes towards more sustainable mining practices. Following the creation of the physicochemical structure of the soil from appropriate mixtures of coal waste with low sulfur content, physical ameliorants and nutrient sources, the inoculation of Technosols with active microbial suspensions may accelerate the decomposition of organic matter present and ensure nutrient availability for plant growth through active nutrient cycling, particularly of nitrogen, sulfur and phosphorous. In this paper, South African ultrafine coal waste was used as the main mineral matrix, and malt residue was used as source of organic matter and nutrients. In order to evaluate the effects of Technosol inoculation, five microbial treatments were used, including the addition of: commercial grade efficient microorganisms (EM Prosoil), anaerobic digested sludge supernatant from treating brewery waste, and ‘tea’ extracts prepared from compost, vermicompost and soil native to the mining area. Growth experiments were carried out using Eragrostis teff, commonly known as teff, a grass typically used for the rehabilitation of mined areas in South Africa. Preliminary results showed that Technosols inoculated with microorganisms performed better in terms of nutrient availability and plant growth. Varied performance was observed as a function of the microbial inoculation applied. This suggests that the inoculation of Technosols with appropriate microorganisms may be recommended to accelerate nutrient availability assisting plant growth during the initial establishing of the Technosols. Technosols continue to show promise as an alternative to both mine waste disposal and the burrowing of topsoils for mine rehabilitation. Keywords: Fabricated soil, mine waste, coal discards, malt residue, nutrient availability, soil microbiology, plant growth

Jan 1, 2020

By T. T. Chiweshe, L. S. Mokhahlane, M. Welman-Purchase

This study examined an alternative technique of extracting tungsten from wolframite ore using a fusion method with ammonium phosphate salt. Current techniques use alkali salts to decompose tungsten ores and use various purification methods to produce ammonium paratungstate, which is a key intermediate precursor in the extraction of tungsten. In this study, a two-step extraction process, which involves thermal decomposition of the ore using fusion and a separation stage, is examined. The novelty of this technique is the ability to completely decompose wolframite ore and form an unstable tungsten oxide phosphate (WO2(PO3)2) compound. The instability of WO2(PO3)2 in deionized water enables selective isolation of tungsten as insoluble precipitates of WO3 and WO2. The decomposition reaction of WO2(PO3)2 is influenced by the presence of oxygen and determined to be first order under ambient conditions. Scanning electron micrographs and X-ray diffraction analysis showed above 80% of the tungsten precipitated compared with the amount that remained in the filtrate solution.

Jul 10, 2024

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

Written contribution by J.F. Curtist The paper is an interesting exercise in the application of mathematics to a theoretical situation presumed to oc¬cur underground. However, some of the assumptions on which the calculations are based are unlikely to occur in any actual mining situation. Assumptions made in the paper Objections to these assumptions are noted seriatim. (1) `it is assumed that any loading-rate effect will be small and can be ignored' (p. 3). A loading rate of the order of 50 kN-12 per cent of the maximum load-is customary to prevent the props being dislodged by the blast. (2) `it is unlikely that all the props will be installed with their full stroke available, but for the purpose of this analysis, it is assumed that this is the case' (p. 3). A more reasonable assumption would be that, with the most careful selection of prop length and the most rigid control of stope width, the available stroke length would on average be reduced by the order of 70 mm on installation-20 per cent of full stroke. (3) `each support unit supports a block of 3,3 m2 bound¬ed by vertical fractures with zero cohesion that are parallel and at right-angles to the stope face respec¬tively' (p. 5). Joughin and Jager have shown this to be an unwar¬ranted assumption in respect of the positioning, the direction, and the dip of the fractures present in a stope in rockburst conditions. If, as assumed, there was `zero cohesion' between such blocks, the removal of a hydraulic prop in row 3 supporting such a block would ensure that it fell out before a profile prop could be installed in the same position. (4) `the height of each of these blocks is 3,0 m, the volume of each block is 9,9M3, the mass of each block is 27 225 kg' (p. 5). The concept of individual props being affected by dis¬crete blocks of known and uniform dimensions of relatively low ground velocities (less than or equal to 2,16 m/s) acting in line with the axis of the prop is one that lends itself to neat mathematical calcula¬tions. It does not, however, bear much similarity to the actual conditions that are exposed underground in excavations where rockbursts occur. Ortlepp and co-workers concluded that `the impulse of the shockwave can cause the displacement of the

Jan 1, 1991

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

Recovered activated carbon fines result from processing of ore and concentrates via cyanide leaching and sorption of valuable metals on carbon at gold-mining plants. This intermediate product is characterised by the particles sized smaller than 0.6 mm and gold grade up to 300-500 g/t. Processing of carbon fines with recovery of valuable metals is not available at many plants due to the lack of optimal technology. The paper describes the testwork and development of an efficient technology to process carbon fines with the recovery of valuable metals into the target gold alloy. This innovative technology involves pelletising of fine activated carbon particles using an organic binder, drying and further firing of pellets in a grate fired furnace at 800-900 °С. The produced ash is subject to sintering with sodium nitrate and hydroxide at 600-700°С. The sintered ash is then leached in water. The insoluble residue containing gold and silver is removed by filtration, dried and smelted to produce gold alloy. Water solution containing sulphur and arsenic is subject to detoxification. Processing of recovered carbon fines according to the developed technology implies the use of standard full-scale equipment. The offered method to treat gold-bearing carbon fines was patented by the Eurasian Patent Office. Key words: Fine activated carbon particles, valuable metals, pelletizing, firing, ash, sintering, leaching, smelting

Jan 1, 2020

By A. J. Dickson, A. M. Starfield

This paper reviews the progress made to date in the development of computer models of heat and moisture transfer from rock surfaces to the ventilating air in deep-level mines. The application of these programs to ventilation planning and design is discussed.

Jan 1, 2014

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By P. E. L. Balestra, A. O. Filmer

The kinetics of the reactions involved in the non-oxidative dissolution of nickel concentrate in hydrochloric acid were studied by electrochemical and powder-leaching methods. It was found that the rate of non-oxidative dissolution increases with a cathodic shift in the mixed potential, which can be achieved by an increase in the nickel-to-sulphur stoichiometric ratio at the reaction surface. An unactivated concentrate with a sulphur content of 36 per cent exhibited a mixed potential of +O,3V (SCE) and could not be leached satisfactorily in 3 M hydrochloric acid at 60°c. When activated material (18 per cent sulphur) was leached, it had a mixed potential of -O,3V, and high iron and nickel extraction rates. Results reported by other workers on the non-oxidative dissolution of sulphides are explained in terms of the mixed potentials at which dissolution occurs.

Jan 1, 1981

Dr J. P. Hugo, Pr. Eng., after obtaining a B.Sc. (Eng.) in Metallurgical Engineering at the University of the Witwatersrand in 1948, gained about 9 months' practical experience in a British steelworks, followed by post-graduate studies at Sheffield University, leading to a Ph.D. (Metallurgy) in 1953. Mr G. Y. Nisbet, Pr. Eng., holds a B.sc. (Min.) from the University of the Witwatersrand (1948) and a P.M.D. from Harvard University, U.S.A. (1966). On graduating, he was awarded the Chamber of Mines' Gold Medal. Professor D. G. Krige, holds a D.Sc. (Eng.) from the University of the Witwatersrand (1963) and a D.Ing. (H.C.) from the University of Pretoria (1981). Dr P. T. Wedepohl holds a B.Sc. (Hons.) from the University of the Witwatersrand (1953) and a Ph.D. from the University of Reading, England (1958).

Jan 1, 1984

1. Journals Quarterly Journal of tke International Tin Research Institute, edited by Colin J. Evans and published by the Institute, Fraser Road, Greenford, Middlesex UB6, 7AQ, England. Engineering, building and construction law review, edited by P. C. Loots and published every two months by Construction Law Review (pty) Ltd (P.O. Box 78020, Sandton 2146, Transvaal), R63,00 per year. 2. Publications of the Mineral Policy Sector Nepkeline syenite and feldspar by B. W. Boyd Potask by G. S. Barry Selenium and tellurium by D. A. Cranstone Sodium sulphate by G. S. Barry Tungsten byG. G. Law-West 3. Mintek reports Report M114 Analytical methods associated with the recovery of uran~um. Report M117 An assessment of tke merits of various types of balls in tke milling of ores. Report MU1 Tke determinatl:on of trace elements in coal by atomic

Jan 1, 1983

Darwin Conference, 1984. Parkville (Australia), The Australasian Institute of Mining and Metallurgy, 1984. $AI5,00 (surface mail). Reviewer: H.A. Simonsen The theme of the Darwin Conference was 'The Mineral Potential of Northern Australia and Changing Concepts of Development', and the fifty papers that were presented commemorate the 'coming of age' of the Northern Territory of Australia. Rockbursts and seismicity in mines, edited by N.c. Gay and E.H. Wainwright. Johannesburg, The South African Institute of Mining and Metallurgy, Symposium Series no. 6, 1984.363 pp. R75,OOexcl. GST, £50, OS$65. Reviewer: E. T. Brown Black sands, by lan Morley. St Lucia (Australia), University of Queensland Press, 1981. Reviewer: P.W.J. van Rensburg Gravity concentration technology, by R.O. Burt assisted by Chris Mills. London, Elsevier Science Publishers, 1984. Volume 5 in the series Developments in Mineral Processing. Reviewer: D.A. Viljoen

Jan 1, 1985