Search Documents

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003

1. Mintek publications The folowing are available from Mintek (Private Bag X3015, Randburg, 2125 South Africa) at R35 (including GST) per copy to purchasers in South Africa and US$30 (including airmail postage) to purchasers elsewhere. Report M402 The preparation of synthetic fusion standards for use in the X-ray-fluorescence analysis of rocks and minerals, by RT. Eddy and J.J. Jacobs. Apr. 1990. 19 pp. Report M405 Slag-metal equilibria in the system Fe-Cr-Si-C-Ca-Mg-AI-O, by R.H. Eric and M. Akyizli. Aug. 1990. 29pp. Application Report no. 8 The development of a process for the recovery of gold from gold-bearing solutions by means of activated carbon or resin in a NIMCIX column. 1990. 19 pp. 2. New publications from Trans Tech The folowing are available from Trans Tech Publications Ltd, Old Post Road, Brookfield VT05036, USA. Efect of iron and silicon in aluminium and its aloys, edited by I. Kovacs. 1990. 450 pp. $124. Martensitic transformations, edited by B'.C. Muddle. 1990. 714 pp. $190. Ferites, edited by C.M. Srivastava. 1989. 2 vols. 1280 pp. $254. Properties and characterization of amorphous carbon films, edited by J.J. Pouch and S.A. Alterovitz. 1990. 714 pp. $152. Synthesis and properties of boron nitride, edited by J.J. Pouch and S.A. Alterovitz. 1990.426 pp. $192. Electronic structure and latice defects in aloys, edited by R. W. Siegel and F .E. Fujita. 1989. 320 pp. $78. 3. A new edition Tomorow's materials, by K.E. Easterling. London, The Institute of Metals (1 Carlton House Terace, London SWIY 5DB, England), 1990. 2nd ed. 170pp. US$29. 4. Books for exploration geologists The folowing books are obtainable from Elsevier Science Publishers, P .0. Box 211, 1000 AE Amsterdam, The Netherlands. Lateritic bauxites, by G. Bardossy and G.J.J. Aleva. 1990. 624 pp. DFL. 295. Platinum-group element exploration, by D.L. Buchanan. 1988. 186pp. DFL 150. Lead isotopes in mineral exploration, by B.L. Gulson. 1986. 246 pp. Dfl. 160. Prospecting and exploration of mineral deposits, by M. Kuzvart and M. B6hmer. DFL. 285. 5. Journal for earth scientists . Ore Geology Reviews, published by Elsevier Science Publishers, P.O. Box 211, 1000 AE Amsterdam, Netherlands. 6 issues per year. Annual subscription DFL 453 including postage.

Jan 1, 1990

By E. Garab, M. Pillalamarry, E. Develo

"Recent geological exploration at Rosh Pinah mine revealed that the mine’s major production is shifting towards the western orefield, which will increase the demand for air flow to be supplied to this area. A snapshot of the ventilation survey carried out in December 2014 at the western orefield drill drive B (WOF-DDRB) showed that the air flow was well below the required standards. In order to improve the existing conditions, possible options were considered and simulated using Ventsim™ software.The best option found was to replace the existing western orefield fans with the larger fans from the inactive southern orefield workings, to increase the air flow in the DDRB district. Simulation showed that as much as 20 m3/s of air can be received at the working faces of WOF 30, compared to the previously received amount of 1.37 m3/s. The economic analysis indicated that the above option can reduce the ventilation cost by N$1.9 million annually. It was also noticed that after implementing this option together with other projects, the ventilation conditions in the mine were greatly improved and currently give no cause for concern. IntroductionA good mine ventilation system should be capable of providing adequate quantity and quality of air to all working faces, and is critical to the occupational health, safety, and comfort of underground employees (Luxbacher and Ramani, 1977; Exikis and Kapageridis, 2006). No ventilation system can remain adequate indefinitely; as the mine workings are extended, the ventilation characteristics such as system pressures, air volumes, leakages, and airway resistances change considerably. Continuous improvement of the ventilation system is needed to ensure compliance with health and safety regulations (Lovejoy, 2010). It also ensures that the right quality and quantity of air is delivered to all the necessary areas at the lowest possible cost. This can be achieved by identifying inefficient airways and poorly ventilated areas in the mine and planning how best to upgrade them.The latest geological exploration shows that the focus of production at Rosh Pinah mine is shifting towards the western orefield (WOF). As mining progressed, the working areas have advanced away from the main fans, which increased the resistance to air flow drastically and resulted in increasing demands being imposed on the main fan in order to supply an adequate air flow. This process also created more leakage paths between the fan and the working areas, which has caused the air to short-circuit before it can reach the faces. Consequently, a much larger quantity of air has to be circulated by the fan so that the stipulated quantity reaches the face, which increases operating costs (Singh et al., 2004)."

Jan 1, 2016

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

By T. Matlou, S. Myendeki, V. Midzi, T. Zulu, H. Mabotja, T. Mulabisana, B. S. Zulu, L. Hlatshwayo, T. Makhateng

The Council for Geoscience (CGS) performed a macroseismic investigation following the occurrence of an earthquake in the Boksburg area on 11 June 2023. The event had a magnitude of ML 4.4 and a focal mechanism that showed the event as having strike-slip motion along a northwest-southeast oriented fault. The event resulted in aftershocks, some of which occurred away from the causative fault in the east in an area without a mapped fault. However, the cluster of past events in that area suggests that there is an active fault. Due to the size of the main earthquake, a macroseismic survey was conducted to determine its impact on the community in the region. Analysis of observed data obtained from questionnaires resulted in the creation of 153 intensity data points. Their distribution showed high intensity values close to the earthquake source area. However, the investigation highlighted a number of anomalies, such as the higher than expected intensity values observed far from the event epicentre. It could be that these anomalies are caused by site conditions, for example, amplification of ground motion due to thick soil layers.

Jan 12, 2025

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

By D. Saramak, T. Gawenda, A. Stempkowska, Z. Naziemiec

The aim of the paper is to discuss the possibility of producing aggregates with an increased content of regular particles, as well as to present a method of aggregate production which has not previously been used in the industry. Traditional aggregate production circuits require the application of three or four grinding stages (depending on the particle size of the feed), but for fine particle fractions of aggregates, irregular grains occur on average with a content of 10%. The innovative technological circuit can produce the aggregates with the content below 3%, even in a single- or two-stage crushing circuit. Downstream jig beneficiation of such prepared material results in higher separation sharpness, lower probable error index (Ep) and imperfection (I). Keywords: Aggregate production, jig beneficiation, mineral processing, raw materials

Jan 1, 2020

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

The April General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th April, 1970, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the chair. There were also present eight Fellows: Dr J. M. Bereza, H. Britten, R. C. J. Goode, C. E. Mavrocordatos, P. W. J. van Rensburg (Council Members), C. A. Border, D. E. French and S. D. Hill. Four Members, J. A. Boyd, P. Crawshaw, D. P. Hugo and A. H. Munro. Two Associates, including I. Robinson. Eleven Visitors, including A. B. Gould, P. M. Haupt, B. Needleman and A. F. Wentzel. Secretary, D. C. Visser. Total Present, 27. OBITUARIES The President: "It is my sad duty to announce the death of the following: Leslie Richard Ulyate, Fellow, who joined the Institute in 1939 and passed away on 10th March, 1970. Stanley Sterling, Fellow, and Corresponding Member for Canada, who joined the Institute in 1926 and passed away on 25th March, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MINUTES The President: "May we confirm the minutes of the General Meeting, held on 21st January, 1970, as published in the March, 1970, issue of the Journal?" Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2., Council has elected them to membership of the Institute in the following grades: Associate: Rupert George CaIcott. Students: Clive Martin Davis, William Machiel Eksteen, Cecil John Tainton. From Student to Member: Dirk Johannes Hugo. "I welcome the newly-elected members to the Institute and congratulate the member who has been transferred to a higher grade." TALK AND FILMS The President: "Mr Ballantyne may I call on you to present your talk and films on the 'Continuous casting of steel'?" After the presentation of Mr Ballantyne's programme the President said, "Thank you very much indeed for your talk and films, Mr Ballantyne. This is a fast developing subject and we appreciate having such up-to-date information being made available to us, particularly those of us who are unable to go overseas for this purpose. We trust that you won't let the matter rest here, but will put everything down in a paper which we can publish at a later stage for the benefit of our members. Thank you once again." CONCLUSION The President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 6.10 p.m.

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By N. V. Nemchinova, A. A. Kozlov, A. V. Epiforov

The gold dissolution in sulfuric acid media during industrial oxidative leaching test of sulfide gold-copper flotation concentrates has been achieved. The reason for this was using technological water containing thiocyanates and cyanides, which can dissolve gold under these conditions. The carbon in column (CIC) process for gold recovery from these solutions was proposed. However, significant amounts of copper and iron were adsorbed onto the carbon during CIC technology industrial tests. This resulted in a decrease of the gold content in the loaded carbon up to 0.5 kg/t. Further development of the technology was conducted by optimisation of gold and impurities stripping and implementation of carbon reactivation. It was shown, that the copper extraction from the loaded carbon during cyanide treatment was about 95%. The copper content in the stripped carbon after cyanide treatment was 1.76 kg/t. The gold recovery during high-pressure elution by caustic solution was 98%. The hydrochloric acidic treatment with thermal pre-treatment (reactivation) for removing iron and calcium from gold-free carbon was proposed. In this case, the iron and calcium extractions from carbon were 40-45 and 50-55% respectively. These tests showed that for carbon recycling the sequence operations of ‘cyanide treatment, gold elution, thermal pre-treatment, hydrochloric acidic treatment’ can be used. Keywords: Thiocyanate leaching, recovery of gold, carbon adsorption, gold elution, copper stripping, thermal reactivation of carbon, activated carbon, carbon-in-column

Jan 1, 2020

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

By A. Marek

The safe and optimal installation of roof support remains one of the biggest challenges in underground mining today. Traditional hand-held, roofbolt installation in conventional mining has been replaced, in a lot of mining operations, by mechanized equipment. This was a first step to moving the operators out of the unsafe working environment and a start on the trend toward a changed support regime in mechanized mining. However, the challenge of handling of the drill steel itself, as well as inserting resin cartridges and bolts, remains a major hazard and the cause of many lost-time injuries. The paper describes and discusses developments in this area, of mechanized bolting and on-board automation, presenting solutions to known problems, achievements to date, and future developments. The solutions presented will identify with addressing customer needs while touching on possibilities for further technology changes, keeping focus on the safety aspect for operators and the need to bring the operators even further away from the unsafe working environment. The-state-of-the-art technology in mechanized bolting equipment is presented and a brief outlook on the past, current, and future developments is given.

Jan 1, 2012