Search Documents

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014

At Namdeb, submerged beaches are earmarked for sampling and future mining and various sampling configurations are tested for optimality through the use of spatial simulations. For the creation of these virtual orebodies, basic statistics and variograms are needed, but in this specific instance no data exists from which the necessary parameters can be determined. The best that can be done is to use proxy data from onshore beaches, with adaptations where needed. The reworking of raised beaches during periods of rising and falling sea levels in some cases destroyed the internal beach structures, and it is very difficult to determine the variograms. A method is proposed whereby simulated annealing is used to adjust the sample locations to align the data pertaining to beach crests or cliff lines, thus improving the variogram structure along the shoreline in the direction of the highest geological continuity.

Jan 1, 2014

By I. Ngo, L. Q. Ma, J. S. Guo

Deformation of gob-side entries has always been a critical concern for ensuring stability in longwall coal mines. This paper addresses the significant deformation and support challenges that arise in thick and hard roof longwall faces (THRLF) due to dynamic pressure. The study aims to elucidate the characteristics and mechanisms of deformation during the retreat of the longwall face. The research findings indicated that the primary cause of deformation was the combination of advanced abutment stress resulting from longwall face mining and the movement of the lateral roof over the chain pillar. To mitigate this issue, we propose a deformation control method known as cutting off the lateral roof (COLR) over the chain pillar. Simulation results demonstrate a significant reduction in roof stress and deformation of the gob-side entry after implementing the lateral roof-cutting technique. These findings provide valuable guidance for effectively managing deformation in gob-side entries, particularly when dealing with thick and hard roof strata.

Aug 3, 2023

By B. R. Broekman, D. W. Penman

Discussion by P.J Lloydt Broekman and Penman describe (J.S. Afr. Inst. Min. Metal., vol. 91, Aug. 1991, p. 261) the addition of sodium cyanide and zinc sulphate to the flotation feed at Prieska. They note that for &apos;safety sake, lime was added to the rod mil to raise the pH to 9,5&apos;, and that &apos;personnel working in the vicinity of the rod mil were required to wear gas masks&apos;. Author reply to P.J. Lloyd We thank Dr Lloyd for his interesting contribution. As he correctly points out, the Prieska float had run with cyanide solutions at pH values of 6,4. In fact, it ran safely for extended period with the pH slightly below 6.

Jan 1, 1991

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By R. C. A. Minnitt, A. Akpabio

This study presents a rigorous comparison between ordinary kriging and commonly used machine learning algorithms, those being, linear regression, support vector regression, decision trees, random forests (RF), and k-nearest neighbours for spatial interpolation of platinum grade estimates in a complex ore body within the Bushveld Igneous Complex. Using only X and Y coordinates as predictors, both ordinary kriging and machine learning models were evaluated at point and block supports under traditional and spatial block cross validation frameworks. While naive validation results suggested superior performance for k-nearest neighbour and random forest (R² = 0.92 and 0.86, respectively), these were revealed to be overly optimistic under spatial dependence. Spatial block cross validation results demonstrated substantial declines in model performance, with R² often falling below zero, particularly for decision trees and k-nearest neighbour, indicating strong overfitting and limited generalisability. Ordinary kriging exhibited more stable, albeit modest, performance under spatial validation, reflecting its strength in geostatistical interpolation when contextual geological variables are unavailable. The study underscores the critical importance of spatially aware validation in resource estimation and highlights that machine learning models constrained to spatial coordinates behave as interpolators rather than true learners of geological variability. Recommendations are provided for future work incorporating geological information to enhance predictive robustness.

Mar 30, 2026

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board&apos;s management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By N. Mashaba, D. Botha

The aims of this study were to investigate the factors that influence women’s engagement in technical positions in the South African mining sector and to determine what could be done to promote their successful participation. A convergent parallel mixed-methods research design was used to ascertain the factors that facilitate, inhibit, and influence engagement. In the quantitative phase of the study, questionnaires were circulated to women employeees; and in the qualitative phase, semistructured interviews were conducted with employer representatives, most of whom were human resource personnel. Confirmatory factor analysis showed that the three-factor structure (vigour, dedication, and absorption) of the Utrecht Work Engagement Scale fit the sample data reasonably well. Although there is room for improvement, respondents demonstrated acceptable levels of engagement in their work. On the other hand, the qualitative findings showed that employee engagement is impacted by unfavourable working conditions, work–life balance, and the mining industry’s male-dominated work culture. The findings showed that employee engagement should be elevated to a core human resource function. To increase the participation of women in mining, human resource professionals are encouraged to collaborate with mine supervisors, managers, and employees to develop programmes that promote employees’ absorption in and dedication to their work.

Nov 6, 2023

The November General Meeting of the Branch was held at the S1. Helena Club on Friday, 15th November, 1968. Mr. J. G. Kirchner (Chairman of the O.F.S. Branch) was in the chair. There were also present: President: Mr R. C. J. Goode. Eighteen Members: Mr A. E. Gilfillan (Council Member), Messrs T. Zadkin, J. N. Saunders, N. A. Honnet, D. D. Waterman, C. R. Netscher, (Committee Members), Messrs G. Thorburn, Z. Lombard, H. V. Henwood, C. J. Isaac, S. L. S. Swart, J. D. McNamara, H. H. Schellhorn, J. W. Wilson, G. C. P. Labuschagne, L. J. Thorne, R. C. Espley-Jones, J. Handley. Seventeen Associate Members: Messrs H. J. Reeders, R. Campbell, P. A. Hoffman, D. E. Couperthwaite, M. D. de Lange, G. J. C. Young, G. W. Futcher, U. Visser, F. H. De Groot, E. Schmid, K. G. Pearce, D. A. Viljoen, H. W. M. Eschenburg, R. Still, W. B. Howe, A. H. Edwards, R. H. Drake. Three Graduates: Messrs T. R. Stromsoe, J. G. Cockburn, T. A. Ward. One Affiliate: Mr O. A. Huss. Twenty-three visitors. Total present: 64. Apologies were reseived from Messrs L. O. W. Leimer, V. C. Barnes and A. Louw. WELCOME TO VISITORS The Chairman declared the meeting open and extended a special welcome to the following: Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Mr A. E. Gilfillan, Member of Council and Mr D. A. Viljoen, all from Johannesburg. Also to Mr J. D. McNamara, the guest speaker for the evening who had made the trip from Oranjekrag. MINUTES OF PREVIOUS GENERAL MEETINGS The minutes of two meetings, viz., the General Meeting held on 26th June, 1968 together with those of the Annual General Meeting held on 14th August, 1968 were taken as read and their adoption moved by Messrs T. Zadkin and D. D. Waterman. MATTERS ARISING FROM THE MINUTES There were no matters arising from the minutes. ADDRESS BY PRESIDENT OF COUNCIL, MR R. C. J. GOODE With regard to the 75th Anniversary of the Institute, the President called upon those present to bear the following two dates in mind, viz.: 21st March, 1969-Banquet at the Wanderers&apos; Club, to which ladies are invited. 24th March, 1969-General Meeting at Kelvin House at 9.30 a.m., the speakers being the President of the Institute, the President of the Chamber of Mines and Dr H. J. van Eck.

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By G. Akdogan, M. Tadie, A. Tapfuma

The Southern African region contains abundant gold tailing heaps that are an environmental concern due to dust pollution and chemical contamination of nearby water bodies. Nevertheless, these heaps contain gold with potential to be extracted for financial gain. In this study, the feasibility of extraction of gold from a Witwatersrand gold tailings using glycine was investigated using a two-level full factorial design. Effects of variables such as glycine concentration at levels of 0.5–1.5 M with a solid–liquid ratio of 50–200 g/L were investigated. Although the solid–liquid ratio used in this study was below the industrial norm, it provides a starting point for investigating the applicability of this technology. To enhance the gold extraction, potassium permanganate pretreatment and copper ion addition were adopted. The results revealed that 91.4% gold extraction was achieved after 24 h pre-treatment of the tailings using 2 g/L potassium permanganate followed by subsequent leaching using 1.5 M glycine at pH 12, with 50 g/L solid–liquid ratio and 2 g/L copper ions. Statistically, the solid–liquid ratio and potassium permanganate pre-treatment of the tailings were found to be significant at 95% confidence interval, whilst interactions of copper ions and glycine concentration were significant factors. The work demonstrates that potassium permanganate pre-treatment prior to glycine leaching of low-grade secondary gold resources, such as tailings, can be beneficial. Furthermore, the methodology developed in this work provides an opportunity for further investigation of the recovery of gold hosted in complex mineralogical matrices.

Apr 14, 2024

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

By T. Mapeta, S. M. Rupprecht

Discussions on reasonable prospects for eventual economic extraction (RPEEE) include the CRIRSCO 2019 reporting template, JORC 2012, SAMREC 2016, CIM 2019 Guideline, and Regulation SK-1300. These reporting codes all conform to the principles of reasonable prospects for eventual economic extraction. To demonstrate that all mineral resources align with the RPEEE principles, the Competent Person is responsible for endorsing the mineral resource estimate. Moreover, establishing mineral resources and RPEEE requires technical input from numerous technical specialists, such as mining and geotechnical engineers, metallurgical engineers, social and environmental specialists, financial and governmental practitioners, and more. The aim is to improve the transparency of the disclosure of mineral resources and guarantee the investor or potential investor that the reporting of mineral resources is based on reliable technical, economic, environmental, social, and other relevant factors. This paper discusses the important protocols and definitions in some international reporting codes for the purposes of developing a guide memoire that will assist the Competent Person to interpret, establish and apply RPEEE appropriately and easily.

Jun 27, 2025

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V, Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By G. Akdogan, I. J. Geldenhuys, Q. G. Reynolds

Efficient recovery of titanium from titaniferous magnetite ores continues to be a promising, yet unrealised opportunity, despite significant occurrences of titaniferous magnetite deposits worldwide and the existence of established industrial-scale practices. Current smelting processes only recover iron and vanadium, while the titanium is discarded in the waste slag. These slags are stockpiled and present massive environmental challenges, while still containing value as residual iron, vanadium and titanium. The complex mineralisation of these deposits does not allow for a significant opportunity to separate the titanium and magnetite minerals through normal physical upgrading processes. An upgrading process is therefore required to derive economic value. An efficient process technology could create an opportunity to unlock all three valuable commodities. South Africa’s Bushveld Complex, the largest known deposit of its kind in the world, is known for the high vanadium content but is also associated with relatively high concentrations of titaniferous magnetite. The quality of the Bushveld Complex was one of the drivers for the establishment of the Highveld Steel and Vanadium Company in the mid-1960s. The unfortunate demise of Highveld Steel and Vanadium created an opportunity to review current practices and evaluate the best available process for this complex ore in the context of the three elements of interest. Past and current processes, the nature of these deposits and the potential to recover titanium are assessed to highlight the potential of fluxless smelting of titaniferous magnetite to produce a titania-rich slag as feedstock to the pigment, titanium metal industry in conjunction with recovery of iron and vanadium. Ilmenite smelting practices are proposed as a suitable alternative to achieve the goal, namely sustainable processing. Keywords: Titaniferous magnetite, titanomagnetite, smelting, titania slags, comprehensive processing

Jan 1, 2020

By B. D. H. Knights

In November 2009 Mintek installed the FloatStar? advanced flotation stabilization system on Vale&apos;s Cauê iron ore beneficiation plant in Brazil. In September 2010 the system was upgraded to include flotation optimization. The circuit consisted of two parallel cleaner circuits producing final concentrate. The tailings from the cleaner section passed through a scavenger circuit. Large, well-instrumented feed sumps played an important role in circuit stability, presenting a good opportunity for advanced control. Previously the plant was controlled using distributed control system (DCS) level control only. The flotation circuit processes roughly 30kt/day. The FloatStar system provided advanced control of the flotation circuit as well as of the sumps feeding the circuit. The system underwent a lengthy trial to assess the benefit that it provided. Two data sets were analysed, showing performance under advanced stabilization and optimization respectively. Several validation and consistency criteria were employed to ensure the quality of the analysis. Iron recovery and iron tailings grade were used to measure system performance. The analysis showed that the system increased recovery by up to 2.7%. In addition, the system decreased the iron tailings grade by between 1.2% (from 23.5% to 22.3%) and 4.3% (from 31.3% to 27.0%) during different test campaigns. The analysis also showed that the entire FloatStar stabilization system was active for 72.7% of the time from first activation to the end of the first data set (approximately 200 days). From the analysis it was concluded that under similar conditions for &apos;ON&apos; and &apos;OFF&apos; tests, the system provides a clear benefit. It was also found that over the longer term, the system continues to provide a benefit. This finding suggests that the results were not simply due to a short-term advantage. The size of the data set, as well as the magnitude of the recovery improvements, lends considerable confidence to these results. Therefore, it can be concluded that the FloatStar control system provides substantial benefit to operations at this site.

Jan 1, 2012