Search Documents

By E. M. Kawenski, J. K. Richmond, M. J. Sapko, G. C. Price

This Bureau of Mines publication presents investigators' reports of all major coal mine explosion disasters that occurred in the United States from 1959 through November 1981, along with a brief analysis of common factors in these disasters, The report reviews the Federal mine health and safety acts of 1969 and 1977, and discusses how implementation of these acts has reduced the number of both fatalities and disasters, Current Bureau health and safety research is summarized, and an appendix lists most of the ignitions and explosions in the period of record,

Jan 1, 1983

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By A. A. Campoli

Retreat pillar mining concentrates stresses on workings directly outby gob areas, which can result in coal mine bumps. The development of bump-control design criteria by the U.S. Bureau of Mines was furthered by data from a novel bump control mining method at the Olga Mine, McDowell County, WY. The pillar splitting, retreat mining system induced large pillar pressure increases and roof-to-floor con-vergence. Roof-to-floor convergence monitoring proved to be a valuable tool in evaluating the pillar splitting mining method and localized destressing techniques. Maximum strain energy storage in chain pillars appears to have occurred just prior to the first of four split cuts. At that point a 15-ft-wide, highly fractured perimeter confined the core of the 55-by 70-ft pillars, permitting the pillar core to support tremendous pressures. Splitting the chain pillars into two 17.5-by 70-ft wings removed the confinement load, resulting in pillar yield. Thus, the pillar splitting mining method successfully redistributed the weight of the roof away from the pillar line. Shot fire and auger drilling destressing techniques aug-mented the pillar splitting mining method by redistributing the weight of the roof.

Jan 1, 1989

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By Thomas M. Barczak, Christopher Mark

Roof supports can only be understood in conjunction with the rock structure that they support. The strength of the rock depends on geology, and the loads are applied primarily by the in situ and mining-induced stresses. Other factors, such as wider spans and retreat or multiple-seam mining, can also reduce the stability of mine openings. Roof supports are used to help stabilize these openings, but their performance characteristics must be properly matched to the loading environment and ground behavior if they are to succeed. Roof supports include both intrinsic supports, such as roof bolts, and standing supports. The key characteristics of any support include its maximum load-carrying capacity, stiffness, and residual strength. Other important factors are the timing of installation, the stability of the support as it is loaded, and the capability of the support system to provide skin control. This paper explains in practical terms how supports work and the important factors in ensuring that a good support design and application strategy are developed.

Jan 10, 2000

By Stuart Lipoff, John E. Trombly, Paul Brien, O&apos

System objectives and design criteria for an in-mine ULF radio paging system are discussed. Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonweath of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By Charles L. Kimbell

Comprehensive data on market prices for crude minerals and mineral products for the world as a whole do not exist, and even the data that are available are not necessarily compatible between countries, particularly between the market economy countries and the centrally planned economy countries. Further, it should be evident that the actual delivered price for a small quantity of any specific commodity at some point substantially removed from a production facility or a seacoast port will differ appreciably from that for a large volume of the same product at or near its production source or a major import center. Nevertheless, the regularly published prices of selected major mineral commodities in key market areas can be regarded as indicative of general world price trends.

Jan 1, 1992

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners' health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry's experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards. The US National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory in Pittsburgh, PA is addressing the safety of this new technology. NIOSH has a proactive project to generate recommendations for addressing the functional safety of PE-based mining systems before the technology proliferates. The recommendations take the form of a safety framework encompassing the entire life cycle for a PE-based mining system.

By Richard C. Repsher

Intermittent mining in the slope section at Dutch Creek No. 1 mine, Carbondale, Colo., of the Mid-Continent Coal and Coke Co. has resulted in erratic and minimal rock noise data, which, in turn, has necessitated a change in the method used to plot daily mine noise in order to be useful to the researchers at the mine. Daily and weekly cumulative plots of rock noise under these conditions have not shown significant stress changes as clearly as bimonthly or longer noise rate plots. Hence, longer term cumulative rock noise plots, as described in this Bureau of Mines report, have been added to the data analysis at Dutch Creek No. 1 mine, and have been shown to delineate unique areas of rock noise activity more clearly than shorter term plots. The longer term plots should aid in the detection and delineation of potential failure areas, when used in conjunction with other proven forms of data analysis.

Jan 1, 1979