Search Documents

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010

By D. B. Dow

This paper on the physical chemistry of oil-field emulsions is the last of a series of three prepared as a result of a study of oil-field emulsions. The first paper3 deals with the factors responsible for the formation of emulsions, find the second4 with methods now utilized for dehydrating oil-field emulsions. A more complete report of the whole investigation is in preparation. The laws governing the formation and resolution of oil-field emulsions fall in that branch of physical chemistry doling with colloids. Much work has been done by the physical chemist on colloids And emulsions, and, although most of this work was on commercial and pharmaceutical emulsions, yet the principles developed apply in a general gray to oil-field emulsions.

Jan 1, 1925

By G. L. Leumann

"INTRODUCTION AND SUMMARYThe Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Red ore (hematite) and blue on (magnetite). Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketch"",Howard J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 1940-45, prospected for lead, zinc, and copper. .His only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast.In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-are deposits indicated by the magnetic survey. 2/ In 1944, an iron-mining company examined this property and diamond-drilled seven holes. Between December 1949 and March 1950, the Bureau of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract."

Sep 1, 1952

By J. H. Stears

This Bureau of Mines report presents information on the use of steel supports in U.S. coal mines, including accident statistics for a 3-yr period and a survey of present applications and problems. It also contains a summary of available steel arch configurations and a description of steel support design criteria for ground control applications.

Jan 1, 1984

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989