Search Documents

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intensive three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to devise a procedure for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 parts per million of W03). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44 percent tungstic oxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process-development unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By W. P. Diamond

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were measured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 670 W -N 280 E (950 separation) for the north, and N 76° W -N 17° E (930 separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By G. S. Rice, R. V. Wheeler

"FOREWORDThe cooperative mine safety research program was carried on successfully in the year 1930 in a manner similar to that described in the report for 1929It is believed that the results of such fundamental work as is being done are unquestionably of great benefit in their application in coal-mining operations, in the saving of life and health of minera. The research result compared and checked by investigations in the two organizations, and further by large-scale tests, as in the Experimental Mine, give confidence to mine operators, miners and State mining officials in the findings of the various researches.The annual report of the contact officers of the United. States Bureau of Mines and the British Safety in Mines Research Board to the Director of the Bureau and the Chairman of the Board respectively, follows:Annual Reports for 1930 To: The Director, Bureau of Mines.The Chairman, Safety in Mines Research Board."

Sep 1, 1931

By Clark F. Grain

The monoclinic to tetragonal inversion of zirconium dioxide was studied by single-crystal X-ray methods, high-temperature X-ray diffractometry, and differential thermal analysis. The unusual features of the inversion, such as no definite transition Lperature, hysteresis, and athermal kinetics, were confirmed for powders who mean crystallite size was greater than 1,000 A. Samples of mean crystallite size below 1,000 A displayed classical kinetics, obeying a logarithmic rate law. A detailed mechanism based on Ubbelohde's theory of continuous phase transformations was proposed which is consistent with all the experimental facts.

Jan 1, 1965

This Bureau of Mines publication describes the plan used to instrument two longwall gateroads at the Powhatan No. 4 Mine of the Quarto Mining Co. Vibrating wire stressmeters, flat jack U-cells, multipoint extensometer stations, and convergence stations were installed in or on the coal pillars, roof bolts, and roof strata of the gateroad entries. The instruments measure pillar stresses, bolt loadings, and strata movements as the gateroad entries are developed and the longwall panel(s) is mined. The report details only the instrumentation plan of the longwall gateroads and not the evaluation of any subsequent data. This is because a complete analy-sis of the data cannot be made until extraction of the longwall panel(s) is complete.

Jan 1, 1982

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By Ludwig Schmidt

Investigations conducted by the Bureau of Dines pertaining to the reduction of evaporation losses of petroleum have shown that such losses may be reduced 70 to 80 per cent by the use of vapor-tight tanks equipped with vacuum and pressure relief valves, and vapor-tight thief hitches. Additional studies have shown that it is often economical to supplement this type of construction with other measures that will reduce evaporation losses still further. Water-cooling systems, insulation, and light colored paints are the measures most often used in connection with vapor-tight tanks. Painting with light colored paints probably is employed in the greater number of cases. On account of the cost of insulation, or of installing water cooling systems, the use of these methods are restricted to tanks containing gasoline or crude petroleum with a very large content of low-boiling fractions. The effect of cooling systems has been discussed in a previous report.2 In choosing paints for tanks many factors must be considered. Probably the three most important are cost, protective value, and color. Many companies have adopted a standard color for all of their tanks in this way they reduce the initial cost of paint by buying in large quantities. The tank farms of such companies usually have a neat appearance, resulting from the uniform painting of all tanks. This procedure also has advertising value. Unfortunately, most of the paints used to protect steel are of the darker colors, usually red or black. These colors accelerate the rate of evaporation. Several companies have solved this difficulty by using a dark colored metal-protective paint as a primer coat, and a paint of any desired color for the final coat. Special metal-protective primers to be used under light-colored cover coats have been placed on the market by several paint manufacturing companies.

Jan 1, 1925

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By Philip G. Freeman

The growth-promoting properties of coal-derived humus were tested by a variety of bioassay methods. Humate materials used included leonardite, a form of naturally oxidized lignite, and humic acids extracted from leonardite. It was found that the greatest effects were evident when water-soluble humic acid was applied to excised root tips. No significant short-term effect was noted when water-soluble humic acid was applied to stem or coleoptile sections. Root initiation was promoted in bean stems when high concentrations of coal-derived humate were applied. Gross weight of tomato plants was increased by up to 40 percent when coal-derived humates were added in concentrations of 101 to 104 ppm to the nutrient in a hydroponic growth test of 6 weeks' duration. It is concluded that coal-derived humate promotes the uptake of minerals, specifically iron, by serving as a metal chelate.

Jan 1, 1968

By Donald E. Graham

A mineral survey of a 12,350-acre portion of the 13,150-acre Juniper Creek Wilderness Study Area (WSA) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1984. The area is entirely underlain by thick flows of Banbury Basalt. Rhyolitic tuff of Little Jacks Creek is exposed in the walls of the Owyhee River canyon beneath the basalt. Minor units of lacustrine sediment occur between the volcanic layers. No mines or claims occur in the area, and no mineralized zones were found. The study area is covered by oil and gas leases or lease applications; there has been no known exploration.

Jan 1, 1985

By Dean H. Ambrose

Computer programs are presented that provide mine electrical systems based on computer modeling for design and safety analysis suitable for large or small computer systems and handheld calculators. Bureau of Mines research has resulted in load-flow, fault, grounding, reliability, short-circuit, transient, and cable ampacity computer models that enable mine power system engineers to analyze their system or to design a system. This report describes the capabilities of the program.

Jan 1, 1984

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By H. E. Powell

A series of alkyl-dithiocarbamic acid amine salts was prepared and tested as collector for slimed lead minerals contained in the waste material from a commercial lead ore concentrator. The reagents, members of a homologous series differing only in the number of alkyl radicals in their structure, were prepared by reacting stoichiometric amounts of primary amines and carbon disulfide in a cold alcohol solution. Subsequent purification was by recrystallization from absolute ethyl alcohol solution. Evaluation was through froth flotation of a mill tailing containing 0.2 percent lead. Results show that maximum recovery (38 percent) was obtained with the reagent containing 8 alkyl radicals, but that maximum rougher concentrate grade (4.8 percent) was obtained with the reagents of intermediate number of radicals.

Jan 1, 1962