Search Documents

By Jon I. Voltz

The U.S. Bureau of Mines has conducted fundamental coal fragmentation studies to evaluate the effects of impact energy and direction of bedding planes on dust generation, size distribution, and impact-output energy relationships. Product size distributions were obtained for the fragmented samples by screening to minus 150 mesh. The minus lS0-mesh fines were analyzed with a light scattering photometer with a measurement range of 176 to 1.9 /.tm. Increased input energy produced a significant increase in the weight of plus 3/8-in material for impact perpendicular to the bedding planes. No significant trend was observed for parallel impact. Impact direction had little influence on dust size distribution, and input versus output energy relationships. As expected, total airborne dust measured at time of impact and percent particulates below 11 /.tm in size generally increased with increased input energy for both directions of impact. Energy used for sample fragmentation increased with increased energy input.

Jan 1, 1989

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

This publication summarizes the in-house and contract research projects programmed for fiscal year 1984 by the Bureau of Mines under its Conservation and Development activity. The document provides a mechanism for interested parties to gain insight into projects of the Bureau's Conservation and Development research program. The objective of the Conservation and Development Program is to provide the technological advances needed to stimulate the mining of domestic deposits containing critical, strategic, and other essential minerals in compliance with existing regulations and at costs sufficiently low to be competitive in world markets. Research efforts are directed toward improving the fundamental understanding of processes and procedures involved in the production of minerals. The overall goals will be accomplished by investigating alternative mining methods to increase domestic production of critical and strategic minerals from low-grade deposits; expanding the technology for the economic and efficient extraction of minerals consistent with cost-effective compliance with environmental regulations; and advancing the technologies needed to insure an adequate supply of coal.

Jan 1, 1984

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By F. P. Haver

The Federal Bureau of Mines investigated aqueous electrolysis as a means for reducing lead chloride prepared by ferric chloride leaching of galena concentrate: NaC1 PbS + 2FeC13 ? PbC12 + 2FeC12 + S°. During electrolysis, metal was produced from solid lead chloride in contact with the cathode rather than from lead in solution. Relatively high current densities--up to 300 amp/ft2--were possible when operating in this way. A very simple cell, having a horizontal lead cathode at the bottom and a vertical graphite anode at the top, was employed. Lead chloride crystals, covering the cathode, were converted to metal powder during electrolysis, and chlorine gas or FeCls was produced at the anode, depending on the electrolyte composition. Electrolytes tried included aqueous solutions of HCI, NaCl, NH4Cl, and FeC12-NaC1. Optimum results (96-pct current efficiency, 0.23 kwhr/lb Pb) were obtained with 20 pct HC1 at 25° C, using a current density of 15 amp/ft2 and an electrode spacing of 1 inch. When the current density was increased, the energy requirement increased also but only to 0.41 kwhr/lb at 150 amp/fr3 and 0.58 kwhr/lb at 300 amp/ft2.

Jan 1, 1978

By G. St. J. Perrott, N. A. Tolch

"The testing of explosives for permissibility for use in coal mines was begun by the technologic branch of the United States Geologic Survey in February, 1909, and continued by the United States Bureau of Mines from July, 1910; this testing has been carried on from year to year as the explosives were submitted by manufacturers. As a result of these many years of testing for permissibility a large amount of data has accumulated regarding the characteristics of permissible explosives. The manufacturer expects a sample of explosive submitted for test to meet the requirements for permissibility, otherwise the sample would not be submitted. However, in spite of the careful regulation and preparation of the formulas a certain percentage of explosives fails to pass the gallery tests. It is therefore interesting to note the proportion of failures at the gallery for a given composition of explosive. The fact should be emphasized that this discussion deals with all explosives submitted for test, both those which passed the tests and those which failed to pass. Explosives that failed to pass the tests were never designated as permissible explosives and have never appeared on any list of explosives permissible for use in coal mines.The Bureau of Mines classifies permissible explosives in two ways, according to the quantity of poisonous gases produced and according to the characteristic ingredient of the explosive.4 In this paper only two types of the latter classification are considered, as follows:"

Dec 1, 1929

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935

By D. Harrington, F. E. Cash

For a number of years the efforts of the coal -mining industry , as well as of the Bureau of Mines , have been directed largely towards the limitation and prevention of explosions in coal mines . The origin of most explosions is ignition of methane or marsh gas , but the extent and violence of these explosions depend chiefly on the combustible dust present . The Bureau of Mines has conducted a large number of tests on the use of incombustible materials in limiting or preventing widespread explosions . The result of these tests , published in Bulletins 167 and 268 and Technical Paper 386 , proves that incombustible dust can be so applied and maintained in coal mines that the ignition of the mixture of incombustible and combustible dusts , or the propagation of flame by the dust mixture , is impossible ; on the other hand , experience and experiment indicate that watering methods are not reliable as a preventive of general or widespread coal-mine explosions . This report describes the use of " mudite , " a mixture of water and finely divided incombustible soil or dirt applied in some coal mines as a means of attempting to limit or prevent widespread explosions .

Jan 1, 1929

By H. C. Ko

Heats of solution of calcium carbon-ate (calcite) and calcium oxide in hydrochloric acid were determined by solution calorimetry. Combination of these two heats yields a value of 42.643±0.024 kcal/mole for the enthalpy of calcination of calcite at 298.15 K. Literature data on ?H°298.15 of calcination of calcite were reviewed and compared. Thermodynamic properties for the calcination process were calculated from 298.15 to 1,500 K using Gibbs energy functions. This research was undertaken by the Bureau of Mines as an effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation.

Jan 1, 1982

By Edward L. McHugh

Mineral resources in the Silver Creek study area of the Nez Perce National Forest. Idaho, were investigated during the summer Of 1989. The study area includes the 36,100-acre Silver Creek-Pilot Knob RARE II area (No. 1-849) on the north side of the South Fork Clearwater River, about 11 miles west of Elk City, 10. Mines in and near the study area in the Tenmile and Newsome mining districts produced about 100.000 02 of gold, mostly from placers. Gold production had an historic value estimated at 52 million, equivalent to nearly $40 million at today's prices. Lode mines produced about 19,000 oz of gold, along with smaller amounts of silver, copper, lead, and zinc. Of 34 mines and prospects examined, ten lode properties are considered to be significant by virtue of their past development or production and the presence of possibly ore-grade mineralization. There are no identified mineral resources in the study area; however, samples that contained gold and anomalous arsenic delineate a three-mile-long area from the Sentinel mine, north to the Blue Quartz prospect where exploration might disclose resources. One mining company is conducting geophysical studies and drilling within the delineated area. In addition, six placer sites may contain enough gold to be of possible interest for future exploration and development.

Jan 1, 1991

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972