Search Documents

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By Carlon S. Land

The Bureau of Mines investigated the influence of a free gas saturation on oil recovery by water drive. A digital computer was used to calculate the combined oil recovery from solution-gas drive to various states of depletion. Results of these calculations are compared and optimum conditions for the maximum oil recovery are found for various fluid-rock systems. For most of the fluid-rock systems, the calculations show an optimum gas saturation other than zero. Using fluid and rock properties as parameters, graphs are plotted showing the optimum gas saturation and increase in oil recovery brought about by the gas saturation. The effects of fluid properties and relative permeability on the optimum gas saturation are seen in these graphs. The graphs can be used as guides in connection with other considerations in determining the optimum time to start a waterflood. They should also be helpful in determining the MER of a water-drive reservoir. The effects of compressibility and solubility of the trapped gas saturation are investigated for select cases using a backward difference scheme to solve the partial differential equation of three-phase flow. From these calculations, it is observed that some benefit of a gas saturation remains for injection pressures up to 1.5 times the original bubble-point pressure.

Jan 1, 1974

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By L. C. George

Addition of an acid waste to an alkaline cyanide waste was investigated for five different combinations of electroplating wastes. At the optimum final pH values of the mixtures, metals and cyanides were almost quantita¬tively precipitated. No evolution of hydrogen cyanide was detected by a few additional processing steps, significant amounts of variable metals were recovered for recycling the waste-plus-Waste step is attractive because no reagents are required, metals arc concentrated, and a relatively harmless effluent that meets most water quality Standards for cyanide content is produced.

Jan 1, 1970

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

By J. H. Soulé

This information circular is one of a series published by the Federal Bureau of Mines describing methods and costs at various mining operations. The Schwartzwalder uranium mine, situated about 20 miles west of Denver, Colo., is an important source of uranium ore in the Front Range. Production was begun in 1953, and nearly 36,500 tons of ore had been shipped by September 1, 1958. The mine is operated by Denver-Golden Oil & Uranium Co., Denver, Colo. Much interest has been shown in the property since uranium mineralization tit was found by Fred Schwartzwalder in 1949. The Atomic Energy Commission, Federal Geological Survey, Office of Minerals Exploration (formerly Defense Minerals Exploration Administration), and Federal Bureau of Mines have done work in the area, and various private concerns have shown interest in the property.

Jan 1, 1960

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By Frank J. Wiebelt

Work on the Abbott-quicksilver property was part of the general program of th~ Bureau of Mines in its investigation of domestic mineral resources, which are essential to national defense or industry and of which our present or probable future supplies are inadequate. The mine was discovered in 1862, and the intermittent production up to 1947 has totaled around 37,500 flasks of quicksilver. Output has come from ore shoots formed in the vicinity of fault intersections in a narrow zone composed of lenses of silicified serpentine breccia interbedded with shale. Work by the Bureau included the drilling of six diamond-drill holes aggregating 2,845 feet. Several possible ore zones were intersected by the drill holes. Field work was begun in April 1948 and concluded in October of the same year. This report gives detailed results of the diamond drilling and a brief account of the history and description of the ore deposits.

Jan 1, 1949

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By R. E. Head

"The microscopic work described below was engaged in primarily into ascertain the approximate proportions in which the copper sulphides existed in the ore examined, and by a comparison of the results obtained from a study of both head are tailing samples to supply data which might be of value in treating the ore by flotation. Incidentally, the physical characteristics and association of the sulphides were noted in order to determine the possible relation or bearing of these features on the present conditions of treatment. Since the copper in the ore occurred as three distinct sulphide minerals - chalcopyrite, chalcocite, and bornite each containing copper in different proportions, there appeared to be little or no possibility of obtaining the desired information by chemical methods of determination.Type of material examinedThe material examined was in the crushed condition and was said to be representative of the flotation feed or heads and the resulting tailing. No hand samples of the ore were examined nor any account taken of the physical condition and association of the minerals in place, because the possible value of the analytical results depended on conditions as they existed in the crushed ore. As the problems under consideration dealt only with the sulphide minerals, especially those of copper, the products from screen sizing were concentrated by hand panning and the gangue discarded. The concentrate obtained consisted almost entirely of the sulphide minerals, since the panning had been very carefully done. The object of this procedure was to obtain a sufficient quantity of high-grade sulphide material, from the sample of each screen size selected for examination, to permit its being so prepared for examination as to be representative of the physical characteristics exhibited by a large number of sulphide grains from each respective size, In the tests and investigations carried on by the company' treating the ore the following sizes had been used in tabulating data and basing conclusions:+48, +65, +100, +150, +200, and -200. These same sizes were used in the microscopic investigation, since the results obtained thereby could be most readily utilized for comparison with the results obtained in previous experimental work, together with deductions based on actual concentration of the ore on a commercial scale."

Jun 1, 1921

By Harold E. Heide

The United States is the world's largest consumer of tin and depends entirely upon foreign imports for its major source of supply. Only a small quantity of tin is produced on the North America continent. The advent of the war in Europe in 1939?brought a threat to our foreign sources of supply, and the Congress took steps to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, and subsequent legislation, the Bureau of' Mines ?and Geological Survey conducted investigations of domestic tin deposits. Most of the tin that has been produced in North America came from the Seward Peninsula, Alaska.

Jan 1, 1948

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By A. W. Newberry

The Virginia copper district is situated in North Carolina and Virginia. It contains many mines and prospects that were active at the turn of the nineteenth century. The Bureau of Mines, as part of the strategic-minerals program, began a project in September 1942 to investigate and explore the most promising of the mines in the district. The Seaboard, High Hill, Durgy, and Blue Wing mines were the sites of the main project activity. This report deals principally with these four mines. Drilling did not discover any new ore shoots but indicated the persistence of known ore shoots in depth. There appears to be no indication of impoverishment of copper with depth.

Jan 1, 1948

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine vas evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, and a previously described/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming; and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive Physical and chemical apparatus. Following the termination of this study of chronic poisoning, possibilities ides for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals rich the adaptation of this new colorimetric method to the determination

Jan 1, 1936