Search Documents

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920

By O. C. Baptist

This report presents results of an investigation undertaken by the Bureau of Mines to determine the clay content of typical petroleum reservoir sands in Wyoming and the effect of clay content on the permeability behavior of the sands. These results should have significance in determining the feasibility of injecting water into the sands for secondary recovery and in estimating the probable damage incurred by these sands if invaded with filtrates from water-base drilling muds. The results of air-, brine-, and water-permeability determinations are given for reservoir sands in three Wyoming fields. The amounts of materials of "fine silt and clay size" (Wentworth scale) in the sands and the types of clay minerals present, as identified by X-ray diffraction methods, are also presented and discussed.

Jan 1, 1955

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

By Thomas A. Jones

An impure variety of barite, which lends itself well to the manufacture of heavy drilling mud for oil wells, is widely distributed throughout the Ouachita Mountains in Arkansas. The ore mined in the area and used for drilling muds usually contains an average of 67 percent barium sulfate, although ores as low as 50 percent BaSO4 are occasionally used. Due to the increased demand for barite for drilling caused by the intense search for hew oil occurrences during the years 1945 and 1946, the Federal Bureau of Mines began an investigation of barite deposits in the Ouachita? Mountains in October 1946. In all, 10 barite deposits were examined, trenched, sampled, and studied during the investigation, which was terminated in May 1947.

Jan 1, 1948

By R. T. Johansen, R. J. Heemstra

In water flooding the gradual accumulation of insoluble materials on the sand face causes the injection pressures to increase while decreasing the amount of water injected . This plugging material often is composed primarily of insoluble precipitates of calcium , iron , and magnesium . Treatment with sodium tripolyphosphate ( STP ) either eliminates or reduces the formation of precipitates . Field tests are discussed showing the almost immediate effects of using STP in the injection water . Methods of treatment , solubility of STP in fresh water and brines , and precautions to observe when starting to treat a waterflood with this chemical are given . Laboratory data show that the preferential wettability of a crude oil for reservoir rock can be reversed by adding a small amount of STP to the flooding water . This reversal in wetting tendency should not only decrease the injection pressures but also increase oil recovery by improving the sweep efficiency of a water flood .

Jan 1, 1964

By C. E. Henning

The total number of petroleum refineries in the United States on January 1, 1958, was 318 and their total crude-oil throughput capacity was 9,407,707 barrels per day, according to the Bureau of Mines annual survey. During 1957, 3 new refineries began operating while 4 refineries were retired. Although there was 1 less refinery, the total crude-oil throughput capacity at the beginning of 1958 was 284,033 barrels per day, or 3 percent, more than the January 1, 1957, level. During 1957 all refinery districts showed increases in capacity. The largest increase, 27 percent, occurred in the West Coast district followed by the Indiana-Illinois-Kentucky district with 14-percent increase and the Texas Gulf Coast district with 13-percent increase. The national increase in capacity had the effect of raising the capacity of the average refinery from 28,601 to 29,584 barrels per day. New crude-oil capacity under construction on January 1, 1958, totaled 185,265 barrels, and an additional 297,885 barrels capacity was reported building as replacement for existing facilities. Included in total new construction were 2 new refineries, 1 in Washington and another in Texas, with planned processing capacities of 45,000 barrels and 8,550 barrels per day, respectively.

Jan 1, 1958

By B. M. Stewart

Researchers at the U.S. Bureau of Mines conducted a long-term groundwater monitoring and site characterization program at an abandoned 10-ha, acid-producing, copper-gold tailings impoundment in north-central Washington State. The purpose was to investigate contaminant release and transport, and attenuation mechanisms in the tailings, sediments below the tailings, and gravels downgradient of the impoundment. This report summarizes the monitoring results and physical properties of the tailings, the sediments below the tailings, and the groundwater system associated with the tailings. Water samples from the vadose and saturated zones of the impoundment were analyzed for 15 constituents. Concentrations of the same constituents were determined in water samples up to 3 m beneath the impoundment and in the shallow colluvium and deep bedrock at 76, 335, and 550 m downgradient and 168 m upgradient. Constituent concentrations within the tailings are quite variable and are influenced by pH, depth of oxidation, grain-size differential (surface area), hydraulic gradient, groundwater mixing, and the presence of hardpan layers, carbonaceous material, and organic matter. Most of the metal constituents decreased to background or near-background concentrations in the farthest downgradient well.

Jan 1, 2010

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By B. J. Moore

This publication contains analyses and related source data for 191 natural gas samples from 22 states and 1 foreign country. Of the total samples, 182 were collected during calendar year 1987. The remainder were collected earlier, but releases granting permission to publish were not received before 1987. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1988

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By N. A. Tolch

[In this partner ?propulsive strength? or "strength" is defined as the relative propulsive effect of an explosive as determined by means of the United States Bureau of Mines ballistic pendulum. The data presented are derived from one particular strength testing device and do not necessarily represent the relative execution value of the different explosives in actual blasting. However, it is believed that the data obtained with the ballistic pendulum fire indicative of the relative propulsive or heaving force and are of value until propulsive strength can be expressed in more fundamental units.]

Jan 1, 1929

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Larry A. Haas

The Bureau of Mines constructed a torsion effusion apparatus to measure the equilibrium vapor pressure of pure metals, alloys, and compounds at temperatures up to 1,500° K. The reliability of the apparatus was established by determining the vapor pressure of silver. The data obtained on solid and liquid silver in the temperature range 1,200° to 1,500° K can be expressed by the following equations:

Jan 1, 1965