Search Documents

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By C. J. Wilhelm, John M. Devine

"Hydrogen aulphide associated with natural as was noted as early as at Point Albino, Canada. 4 The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence ma by no means common. However, in recent years, with the development of the producing zones of west Texas and the Texas Panhandle the production of ""sour"" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor-frequently a major problem—in the drilling and operation of any wells in those areas.The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen sulphide. From the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. 5 Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.6"

Sep 1, 1931

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By R. V. Lundquist, H. Leitch

The solubility characteristics of three calcium aluminates , 12Ca0 · 7A120½ 3Ca0 A1203 , and 4Ca0 A12 03 Fe2O3 , were determined in water and in solutions of NaOH and Na₂ CO₂ to more clearly define their role in relation to the recovery of aluminum by the lime sinter and the lime - soda sinter processes . The calcium aluminates were prepared by sintering stoichiometric mixtures of CaCO3 , Al2O3 3H20, and Fe 0 at 1,375 ° C. The rates and extent of aluminum extractions were determined . The aluminum extractions from the aluminates were dependent on the presence of carbonate ions in the leach solutions , temperature , time , leach solution composition , and solid - liquid ratio of the slurry . The aluminum extracted from the calcium aluminates in water and in NaOH solutions varied from 4.6 to 22.9 percent . Virtually , complete extraction could generally be obtained for 12Ca0.7A120 and 4Ca0.A12 03 • Fe₂ 03 ; in one instance it was obtained for 3Ca0.A1203 , when an excess of carbonate ions was present over that required for the conversion of all of the calcium in the aluminates into CaCO3 . In some cases of poor aluminum recoveries , extractions could be improved by regrinding and releaching the solid residues .

Jan 1, 1964

By Oliver Bowles

"On January 15, 1920, a man was killed by falling rock in a limestone quarry in Utah. The quarry was visited by a representative of the Industrial Commission of Utah, and the cause of the accident was carefully determined. The facts concerning this accident, and the Bureau's recommendations are given in some detail in the hope that quarrymen may take steps to avoid dangerous conditions, and thus reduce the liability to accident.The quarry rock face is about 180 feet high, and the ledge is covered with an overburden of 10 to 20 feet of a mixture of soil and boulder. The rock face is not vertical, but slants at an angle of about 45° to 50°, while the stripping face stands at an angle of 70° to 80°, and is flush with the rock face. The conditions are shown in the accompanying figure.The man who was killed was employed in breaking rock at the foot of the quarry wall. The sun had been shining on the stripping face, and probably thawed the ground, thus permitting a boulder weighing about 20 pounds to roll down the slanting face, striking, and almost instantly killing the workman who was working with his back toward the quarry wall."

Feb 1, 1920

By R. R. McLellan

The Brown Derby pegmatites are in Gunnison County, Colo., about 18 miles east of Gunnison. Approximately 860 tons of lepidolite concentrates, with smaller amounts of microlite and beryl, was produced from 3 dikes of the Brown Derby group from 1943 through 1947. No mining was done from 1948 until December 1950, when production of lepidolite and beryl was resumed by the Poston Mining & Milling Co. Mining was intermittent during 1951 and 1952. The dikes were mapped and studied by the Federal Geological Survey during the field seasons of 1942 to 1944, and in May 1950 the Bureau of Mines initiated a diamond-drilling project to test the three dikes for lepidolite and beryl. After being recessed twice, the project was terminated indefinitely July 1951. Seven drill holes were completed for a total of 1,841.6 feet of drilling.

Jan 1, 1956

By Oliver C. Fursman, Lloyd H. Banning

This research was undertaken to determine the feasibility of producing steel from hydrogen - reduced , pyrophoric iron powder . Before steelmaking tests were begun , investigations were made to develop procedures for handling the pyrophoric powder safely , and melting tests were made in a single - phase , electric - arc furnace to determine inert gas requirements for preventing powder oxidation . Steelmaking tests were conducted in a conventional electric - arc furnace , usually by a two - slag basic procedure . Results of the research indicated that ( 1 ) pyrophoric powder can be handled safely and can be prevented from oxidizing excessively during charging and melting in electric - arc steelmaking furnaces ; ( 2 ) little , if any , more electrical energy is required for melting Cerro Bolivar iron powder per unit of contained iron than is required for melting heavy melting scrap ; ( 3 ) high - quality steel can be produced readily from high- grade iron powder , having recoveries up to 95 percent of the total iron ; ( 4 ) steel can be produced from simulated titaniferous , chromiferous , and manganiferous iron powders ; and ( 5 ) the electrical energy required for melting increases with increase in the proportion of slag - forming constituents in the furnace charge .

Jan 1, 1964

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)' The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

By Sabri Ergun

Previous studies of magnetic separation of pyrite from coals have been reviewed critically. Magnetic susceptibilities of United States coals of differing rank have been measured. The effects of crushing, magnetic mixing, drying, weathering, and heat treatment on the enhancement of the magnetism of pyrite have been analyzed. The importance of size distribution of pyrite in the coal and the necessity of crushing to liberate the pyrite has been discussed. It has been found that the inherent susceptibilities of the carbonaceous, mineral-free portions of coals (? -0.5 X 10-6 in cgs units) and of relatively pure pyrite isolated from coals (? -0.3 X 10-6) do not permit efficient separation of pyrite from coal; the average susceptibility of the magnetic fraction of coal must be raised to 3 X 10-6. Friction forces encountered in crushing sedimentary pyrite embedded in coal do not increase its susceptibility. Subsequent weathering or heat treatment below 400° C leads to the formation of iron sulfate and hence increases the effective paramagnetism of pyrite. Ferromagnetic compounds of iron are not formed in significant quantities at temperatures below 400° C. The degree of liberation and apparent susceptibility of pyrite are the most important parameters in its separation. It is concluded that effective beneficiation of coals can be achieved by magnetic separation. A sufficient increase in the susceptibility can be achieved by converting less than 0.1 percent of pyrite into ferromagnetic compounds of iron. Such conversions occur only at temperatures >500° C. An investigation of the dielectric properties of coals and pyrite in the frequency range 0.1 to 60 Mhz indicates that the imaginary dielectric constant of the pyrite is about 100 times larger than that of coal. Exploratory experiments indicate that pyrite can be selectively heated to temperatures above 500° C without appreciable rise in the temperature of coal. It appears that dielectric heating of coals in the Ghz frequency range is the most feasible method of enhancing the paramagnetism of pyrite.

Jan 1, 1968

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976

By V. A. Danielson

The Bureau of Mines examined sources, consumption, and movement of iron and steel scrap in the southeastern States--Alabama, Florida, Georgia, Kentucky, North Carolina, South Carolina, and Tennessee. Officials of the scrap-processing and scrap-consuming industries were interviewed, data was obtained from the published literature, and a canvass was made by the Bureau of scrap consumers. The Southeast generated excess scrap which was shipped to domestic and foreign consumers in about equal proportion. Total 1963 demand in the Southeast was 3,336,000 net tons, of which purchased scrap was 75 percent, foreign exports 13 percent, and domestic exports 12 percent. Alabama, with 47 percent of the purchased scrap consumption in 1963, was the most important scrap-consuming State, and Kentucky, with 34 percent, was the second most important one. Southeast demand was 4.8 per-cent of the total U.S. demand. Projected 1980 consumption is 8,340,000 tons. Scrap prices showed a slight downward trend for the period 1953-63, although gross consumption increased slightly. A significant trend in processing scrap in the Southeast is the preparation of smaller bundles or "briquettes" weighing from 75 to 150 pounds, which are easier for consumers to handle and inspect. Another significant development is the "shredding" of automobile scrap which produces a dense, clean scrap especially desirable for use in electric furnaces.

Jan 1, 1967

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By D. L. Forrester

This paper, describing the milling practice of the Old Dominion Co., is one of a series being prepared by the: United Staten Bureau of Mines. ACKNOWLEDGMENT In the preparation f this paper, acknowledgment is made of the valuable service rendered by R. S. Allen, metallurgist of the Old Dominion Co. T. G. Chapman, one f the consulting engineers of the Bureau of Mines, assisted in arranging the paper for publication.

Jan 1, 1931

By J. B. Gayle

During the past several decades, there has been a steady increase in the number and size of experimental ovens used for carbonization research. Although many were originally intended principally for studies of coal expansion, current practice usually includes determinations of the properties of the experimental cokes. With respect to size and shatter characteristics, the cokes from the larger experimental ovens closely approximate those from duplicate charges carbonized in commercial ovens; however, they are consistently lighter and frequently less resistant to degradation by abrasive forces. To minimize these differences, some operators dry the experimental charges before carbonization. The resulting higher dry coal charge densities do, in fact, yield cokes with gravities closely approximating those produced commercially from the same coal or blend but without drying. The drying of the experimental charges may be criticized on the grounds that it represents a departure from commercial practice and may result in oxidation of the samples; for these reasons, the practice has not been universally adopted.

Jan 1, 1961

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961