Search Documents

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By M. J. Waller

Surface resistivity techniques were used at four field sites to monitor changes in apparent resistivities with variations in soil moisture content in the vadose zone. Apparent resistivity values were correlated with gravimetric moisture contents from soil samples taken at each site. Tensiometer readings were taken at two sites and correlated with the results of gravimetric moisture contents and apparent resistivities. Moisture at two of the sites was added by extensive watering; rainfall events were monitored at the other two sites. A recharge event at a dewatering program was monitored at a fifth site. A Ghosh-Koefed multi-layer computing algorithm was used to derive true resistivities from bulk or apparent resistivities. An automated data acquisition system was developed to measure resistivity changes and to process the data in the field. These studies are the first to evaluate measurement of moisture migration in clay rich soils using surface resistivity techniques. Results indicate that surface resistivity techniques readily measure changes in moisture contents in the vadose zone in clay rich soils. Correlation of apparent and true resistivity values with gravimetric moisture contents is more complex and requires additional research.

Jan 1, 1986

By Sumner M. Anderson

THE importance of the mineral industries of the Latin American area in 1964 may be evaluated in respect to a number of points of reference, a few of which are measurable and appropriate for examination. With regard to the region's contribution to total world production, it accounted for total 1964 world output of natural nitrates (from Chile), and about 97 percent of the optical and electrical grades of quartz crystal (from Brazil). The region supplied over 20 percent of world output of 7 other mineral commodities and accounted for 4 percent or more of world output of 19 other mineral products. Among major commodities, the area, occupying 15 percent of the earth's land surface, supplied within 3 percent of that proportion of the world's output of copper, lead, tin, zinc, barite, and crude petroleum. Incomplete compilation of production data, particularly that of nonmetallic minerals, precludes production estimates on some items for the area ass whole, and therefore the importance of Latin America as a world producer of some additional commodities may not be clearly assessed. For example, most of the countries of the area collect only incomplete data or no data at all on the production of clays and other ceramic materials, sand and gravel, dimension and crushed stone, lime, ornamental and precious stones, perlite, vermiculite, carbon black, coal tar products, and petrochemicals. In the case of many countries of the area, the value of production of one or more of these commodities greatly exceeded that of other mineral industry products that are carefully reported.

Jan 1, 1966

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By Richard H. Spencer, Thomas E. Doerfler, Robert L. Lagace, James M. Dobbie, William S. Hawes

This report assesses the expected detectability, on the surface above mines, of electromagnetic signals produced in the frequency band of 630 to 3030 Hz by a rescue transmitter activated by miners trapped underground. This assessment is based on a statistical analysis of experimental signal and noise data taken at a representative sample of coal mine sites well distributed over the United States underground coal fields. Regression analyses are performed to characterize the signal transmission behavior of overburdens as a function of depth and frequency. The predicted signal behavior is then combined with experimentally based distributions of the background noise, and aural detection characteristics of signals in noise, to generate curves of the expected probability of detection for trapped miner signals versus overburden depth and operating frequency. The implications of these results, and associated recommendations, are presented regarding the detectability of trapped miners, sensitivity analyses and confirmatory tests, and operational utilization considerations for the trapped miners and the search and rescue team on the surface.

Jan 7, 1980

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2001

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By E. K. Kleespies

The Bureau of Mines demonstrated a technique for electrowinning titanium from titanium nitride and titanium dioxide. Titanium-nickel-copper metal solutions containing 26 to 61 weight-percent titanium were prepared by electrolyzing titanium nitride in molten mixtures of potassium fluotitanate) and sodium chloride or barium chloride and depositing titanium on nickel-copper cathodes. A titanium-nickel alloy was prepared by electrolyzing titanium dioxide in an electrolyte of potassium fluotitanate) sodium fluoride) and calcium fluoride and depositing titanium on solid nickel cathodes. This alloy contained 21 weight-percent titanium and had a combined oxygen-carbon content of less than 0.1 weight-percent. A compartmented cell confined the oxide feed near the anode and inhibited oxygen contamination of the metal.

Jan 1, 1966

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By T. OnIin, F. F. ApIan

"A study has been made of the surface properties of coals of differing ranks, in their natural state and as modified by the addition of collectors. The evaluation of their surface properties has been done by captive bubble contact angles, water and methylene iodide sessile drop contact angles, zeta potential, point-of-zero charge (PZC) shift, and flotation. .changes in the hydrophobicity of coal is a function of both the rank of the coal and the collecting reagent.INTRODUCTIONThe chemical and physical properties of a raw coal will determine its response to a given beneficiation process. .For such processes as flotation, filtration, flocculation, dispersion, handling, dust supression and agglomeration, however, it is also necessary to consider the surface properties of the coal and mineral matter constitutents of the raw coal. In the case of a specific particle to be floated, it is also necessary to consider the properties of the coal as modified by the addition of some reagent designed to modify (usually increase) the hydrophobicity of the coal surface. General properties of the coal have been well summarized by Van Krevelen (1) and Elliott (2), while the data for the surface properties of coal are much more scattered in the literature (see, e.g.: Parekh and Aplan (3), Gutierrez-Rodrigues et al. (4), Aplan (5), Arnold and Aplan (6), Hogg and Chander (7) and Rosenbaum and Fuerstenau (8)). While a knowledge of the inherent surface properties of a sample are important, of much greater practical significance are the properties of the particle in the presence of a reagent, such as a collector, designed to enhance the hydrophobicity of the particle. This study will focus on the surface properties of coals of various ranks in the presence of a variety of collectors."

Jan 1, 1989

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By Ronald M. Van Noy

A reconnaissance study of kyanite-group mineral deposits in the Northwest has revealed large exploitable reserves of the mullite-forming raw materials in the Woodrat Mountain and Goat Mountain districts of north-central Idaho. Potential coproducts or byproducts are garnet and muscovite mica. The Woodrat Mountain district contains garnet-kyanite-mica schist, which has been traced for 6 miles and may extend farther. Surface samples average 29 percent kyanite and contain up to 15 percent garnet. Inferred reserves of strippable ore with a low waste-to-ore ratio, and containing more than 15 percent kyanite, are more than 3 billion short tons. The Goat Mountain district contains several kyanite-mineral zones. Samples of the richest zones average from 10 to 20 percent kyanite minerals and represent about 200 million short tons of strippable rock. Beneficiation tests indicate that the kyanite minerals and garnet can be concentrated by a combination of gravity, flotation, and electromagnetic methods. Reserves in these deposits are sufficient to satisfy any foreseeable domestic and export demand. However, the freight tariff to reach the nearest major users of kyanite (located in the Midwest) has discouraged development of western kyanite resources. Western demand of a magnitude to support a moderate to large milling operation has not yet been developed. However, there is some foreign market potential. If a garnet byproduct could be prepared and sold for coated abrasive products or as grinding grains, an offset possibly could be gained to a por¬tion of the mining and milling costs for the Pacific Northwest producer. Such byproduct values would offer a means for expanding the geographic market areas as well as the regional market potential.

Jan 1, 1970

By G. E. McElroy

[The ventilation of development faces In nines for diluting Gas or dist concentrations and, in hot nines for providing air-motion cooling effect, by fan-pipe units discharging high-velocity steams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, n subject on which little definite information is available. A study of the air flow from grills into rooms3/ has provided some basic data, but under conditions so different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.]

Jan 1, 1940

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although eliminating hazardous noise is the long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use is usually quite different (i.e., worse) than when tested under lab conditions. In addition, workers may refuse to wear their hearing protection for any number of reasons. This project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis on optimizing the balance between effectiveness, comfort, over protection, and communication ability. The recently completed auditory research facility is now under-going the accreditation process conducted by the National Institute of Standards and Technology under the National Voluntary Laboratory Accreditation Program. Experiments are planned to investigate the factors that affect a miner’s ability to hear hazard and warning sounds (e.g., roof working, alarm signals, spoken communications, etc.). A service contract has been initiated to record and digitally store samples of typical warning sounds heard in an underground coal mine. This information will be analyzed in the lab to develop recommendations that can be offered to the mining community regarding correct earplug/earmuff usage to maximize there cognition of hazard and warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2001