Search Documents

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By H. W. Gillett, A. E. RHOADS

In its study of methods for reducing metal losses in the non- ferrous metal industry, the Bureau of Mines has conducted a long series of experiments on electric brass melting and collected much data on the experiments of others. Reports bearing on this work that have already been published by the Bureau of Mines are Bulletin 73, "Brass-furnace practice in the United States," and Bulletin 77, "The electric furnace in metallurgical work." A comprehensive report describing the design and operation of all types of electric brass furnaces and showing their performance in experimental tests on a commercial scale is in course of preparation. However, commercial tests of several new and promising types of furnaces are still under way, the results of which should be included in any general discussion of the subject. For this reason it has seemed desirable to issue a preliminary bulletin giving the data on a type of furnace developed in one stage of the bureau's work.

Jan 1, 1918

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By (NIOSH) Publication

In 2004, a total of 2,011 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.9% of all mining operations.

Sep 1, 2007

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department?s Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

In 2005, a total of 739 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 26.9% (n=199) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By G. W. Birge, D. E. Wolfson, J. G. Walters

Seventeen samples were carbonized by the BM -AGA pilot - plant test method and in industrial ovens . Chemical and physical properties of the samples were determined , and the physical properties of the cokes prepared by the two methods were compared . Since the capacity of the plants from which these samples were obtained is about 30 percent of the 1959 total for the United States , the data given in this report are indicative of the chemical and physical properties of blends used to produce industrial cokes and the acceptable chemical and physical properties of the resultant coke .

Jan 1, 1964

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By E. R. Maize

[In %-port of Invcstiptionn 7452 ,g dcniing with roof ~wet,ent in the Cmcibla r~ine, rof&apos;erence .,as m.da to the f~ct tiwt timker decny war, bsing studied at tho tine of writing. Thic napor, written a3er completion of that ~tudy, describ~s t1l.e ~mrl&apos;: and sunlharizea the fiats obtained. Ifhen tlle stu* oi roof novement bras be,- at Cxcible tw igeas \%.ere a6-r;incsd. on decay of tiriber Q: scne of :he olficialr;: (I.) 9:la.t timber decay v:as unustmlly rapid in ,tho Ciuoiblc mins, ,m?. ((2) that timber coated with rock ri..~st deixiyad morrl mpirlly thnn those %hat vsrc not so coated. Thsx ::ore no records by which tkeso &apos;iaeas could &apos;L;e tertcc?, ard it cnpsarefi vise to make a limite6 in- vo3tiption, p~.rticu!.ai.ly of +.he effect of roc!< dusting on decny, as rock ductirg is nn importnnt mer-ns of ~rc-,rcnt?;~g cad-dust eql-osions. ]

Jan 1, 1941

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,&apos; and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user&apos;s manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By J. I. Paige

The Bureau of Mines studied methods for recovering unreacted titanium minerals and petroleum coke from titanium chlorination plant wastes prior to neutralization treatment with lime. The objective was to recover valuable raw materials and to reduce the amount of waste materials that must be treated for disposal. Samples of solid wastes were physically beneficiated by gravity concentration (tabling) to recover titanium minerals containing 69.0 to 92.4 wt-pct Ti02 and by selective carbon flotation to recover petroleum coke containing 94.0 to 96.8 wt-pct C. Laboratory data indicate that the recovered titanium mineral would decrease the amount of solid waste to be disposed of from 32.8 to 53.9 wt-pct. The recovery of coke would further decrease the amount by additional 32.9 wt-pct. Preliminary tests conducted on recovering vanadium, chromium, and columbium from liquors obtained by leaching chlorination residues also have shown that (1) 97 pct of the vanadium was extracted from leach liquors in a two-stage solvent ex-traction procedure and (2) 58 pct of the columbium and 40 pct of the chromium were separated from the leach liquors by an ion exchange technique using a strong acid resin.

Jan 1, 1982

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.