Search Documents

By Thomas J. Peters

The U.S. Bureau of Mines and the U.S. Geological Survey are responsible for the evaluation of the mineral resources and potential of further planning areas included in the U.S. Forest Service Roadless Area Review and Evaluation (RARE II) program. The Bureau of Mines primarily evaluates mineral deposits and prospects within the areas. The Geological Survey naps the area's geology and conducts geochemical sampling. Evaluations are in conformance with the Forest and Rangeland Renewable Resources Planning Act of 1974 as amended by the National Forest Management Act of 1976. The Hauser RARE II area, which consists of 7,600 acres (3,100 ha) within the Cleveland National Forest, is in southern San Diego County, California. The area, which forms the north slope of Hauser Canyon, ranges between 1,600 and 3,919 ft (490 m) in elevation. It is sparsely to densely covered with desert shrubs. The area is underlain by granitic rocks of the Peninsular Ranges batholith.

Jan 1, 1983

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By Dennis J. Grigal

The objective of this contract was to monitor operating conditions of, four flooded, fibrous-bed filter panels used during normal underground mining operation and to analyse clogging and structural problems. After observing structural and clogging problems and conducting laboratory and field tests, a final, Flooded, fibrous-bed filter design which minimizes clogging and structural problems was recommended to the Bureau of Mines. This report also describes the dust sampling procedures used to determine the dust concentration at the flooded, fibrous-bed scrubber intake duct.

Jan 1, 1979

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975