Search Documents

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By P. A. Kennedy

An environmental assessment or impact statement for onshore waste disposal under the Notional Environmental Policy Act is expected to occur with the development of commercial deep seabed mining. An environmental assessment was conducted in order that testing and refinement of nodule waste disposal techniques can he completed prior to 1988, when commercial seabed mining can begin under U.S. legislation. Within this study three classes of process and four classes of waste disposal technique were identified, and five sites were selected as representative of first-generation nodule operations. Each realistic site/process/disposal technique combination was compared against potential effects to determine important characteristics of the rejects and the sites. Regulatory requirements were also considered at each site to identify important issues and their effect on the permitting process. Principal conclusions in the report are the following: (1) uncertainties exist in the regulatory regimes for hydrometallurgical process tailings, primarily regarding classification as hazardous waste; (2) slogs from nodule processing are expected to be inert and relatively easy to dispose of at all sites; and (3) additional physical and chemical information on properties of rejects from all processes is necessary to predict environmental effects.

Jan 1, 1982

By Frank L. Wideman

THE TREND towards larger quantities of waste in materials handled at metal and nonmetal mines (excluding fuels) continued. A gain of 10 percent from 1962 in the tonnage of waste removed in mineral operations reflects the kind of technological problems being encountered. Technology has a major role in the mineral industry in the task of supplying raw materials obtained from resources occurring beneath the surface of the earth and used in manufacturing commodities essential to modern living. Changes in technology are often brought about by such factors as variations in economic conditions, differences in physical properties of raw material and changes in mineralogical compositions of ore. Mining is usually begun on the richest and most accessible of known deposits, and when these are exhausted, is continued with leaner ores or with less accessible deposits that are either lying at greater depths or are more remote from markets. The increasing difficulties of extraction and depletion of reserves are offset by improvements in extraction technology, improved transportation, and exploration for new deposits. Although depletion has prevailed at many individual mines and in many districts, technology has been the means of providing for increasing demands of an expanding economy with adequate supplies of minerals despite either the changing character or decreasing grade of certain ores. This has been accomplished by various methods applicable to minerals. Among the implements of technology are utilization of lower grade or more complex refractory ores by mass mining, concentration, processing, recovery of byproducts, and mechanization. Better methods to find concealed deposits or to penetrate to greater depths also have been helpful in maintaining a supply of particular minerals.

Jan 1, 1964

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By Robert C. Gabler

Three filter cloth fabrics commonly used in drains for coal waste embankments were tested by the Bureau of Mines for clogging behavior and deterioration under simulated field conditions. The objective was to provide guidelines for the mining industry for the proper selection and use of filter cloths to assure safer embankments at mine waste disposal sites. The filter cloths were tested with three coal waste samples in stand-pipes used to simulate coal mine waste disposal environments. Two of the cloths showed a tendency to become clogged with fines from the wastes. One waste caused clogging by precipitating an iron-silicon compound on the test cloths. No apparent cloth deterioration resulted from exposures to the simulated coal waste environments. (The exposures ranged from 2 to 12 months.) In other tests, exposures to waters in the pH range of 2 to 12 and to reagents used in coal-preparation plants resulted in insignificant or no deterioration, as measured by tensile strength. However, long exposures to sunlight (ranging from 4.6 to 6 months) caused major deterioration in two of the cloths (86-and 98-pct losses in tensile strength) and slight deterioration in the third cloth (9-pct loss in strength).

Jan 1, 1984

By A. F. Colombo

Bench-scale research was undertaken to determine if adding ammonia to cyanide leaching solutions would enhance the extraction of copper from an argillaceous Michigan copper ore. Two leaching techniques, (1) rolling using a tumbling bottle and (2) aerating using a modified Buchner funnel, and variations in pulp temperature; were employed in evaluating the effect of ammonia concentration on copper extraction. Under these experimental conditions, the extraction of copper was shown to be independent of ammonia concentration and entirely dependent on cyanide concentration.

Jan 1, 1968

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968