Search Documents

By GEORGE S. POPE

This bulletin is a revision of Bulletin 63 and is published by the Bureau of Mines in order that purchasers of coal for Government, State, municipal, or private use may be informed regarding advances or refinements in sampling coal deliveries and preparing specifications for the purchase of coal. The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form, but the same in principle, has been gradually adopted by other departments until, at present, of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publioations a listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples representing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the specification method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly representative of the commercial product delivered in wagons, railroad cars, or ships. Therefore the method of taking and preparing samples for shipment to the laboratory has been given fully as much care as the making of the analyses and tests, and a general plan of collecting samples fairly representative of the delivered coal has been evolved through various modifications and improvements based on experience and increased knowledge of the physical and chemical characteristics of the various coals that are purchased by the Government. The method that is in general use by the Government is described in the following pages. In connection with studies of the coal deposits of the country, of the best methods of preventing waste in mining, and of increasing efficiency in the utilization of coal belonging to or for the use of the Government, geologists and engineers of the United States Geological Survey and of the Bureau of Mines have visited more than 2,500 coal mines scattered through all of the coal-producing States and Territories. From each mine 2 to 8 or more samples were taken, the number depending upon the size of the mine and its output. The analyses and descriptions of the samples collected up to the end of the fiscal year 1913 are published in Bureau of Mines bulletins 22 a and 85,b and those of samples collected in the fiscal years 1914 and 1915 are presented in a bulletin that will soon be published by the bureau. A study of the analyses of these samples and of the samples taken from cars shipped from a number of the same mines shows that the mine samples are as a rule of higher grade than the average commercial shipments, particularly with respect to containing a lower percentage of ash and having a correspondingly higher heating value. This difference is due to the fact that the Government inspector, proceeding on the basis of what can be done by a good miner, usually removes more of the partings of bone, slate, and other extraneous matter from his mine samples than the average miner does in ordinary practice, the aim of the miner being to get the maximum number of tons past the tipple inspection, as his earnings are based on his output. The average miner, therefore, does not always take as much care as he might in rejecting the impurities. The difference may be caused, too, by the presence of pieces of the mine roof and floor in commercial shipments. The Government inspector can readily

Jan 1, 1916

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Shih-Chi Chang

[An exploratory research is done on untreated coal 1v- using&apos; x-ray crnctinn techniques. Comparison is made on diffraction data before And pct Pr n-tiAne is pressurized (n the coal samples. Although, only ? qualificative -1; t s obtained, the FoIIowing Statement r :&apos; n untreated teal seem- There are other materials in cost. They are accumilated in !e ,r rc r, cin? the microseoric layered structure of coal. 7"P partial graph r :r a&apos; o., «&apos; the i&apos;pr1 cart o ! in cna1 assumes varclor, r,rie&apos;,r: r in&apos;is. R nr ?-&apos;c,.r1&apos;ed I n coal is helm ;n the micrornre s&apos;??ste^ o&apos; c, .:l an&apos; t rr i, ,o <.~i:&apos;epee of Ion(4inc to carton h« x-ray tit If raction me.:SUr&apos;rientq. :t?e me r &apos; nP in r^icropores assumes no structure themselves at room tempera¬FLre. ;inally, some of the other materials in coal are in the form of }vrlrited crystallites and they have anisotropic pro&apos;th hnt&apos;1? in the lavers.]

Jan 1, 2012

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau of Mines, which conducts research on many of the complicated and frequently interrelated problems of extracting crude oil and natural gas from the ground, transporting them to market or to places for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because may of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau f Mines, which conducts research on many of the complicated and frequently interrelated problems f extracting crude oil and natural gas from the ground, transporting them to market or to daces for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because many of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators&apos; needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user&apos;s handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By Spencee L. Willett

A sand and gravel deposit exists in the Wildrose Canyon Wilderness Study Area (WSA), Out it is limited to local use because of the distance from major markets and resulting high transportation costs. The WSA has no identified metallic minerals, oil, gas or other energy related deposits. INTRODUCTION The WSA encompasses 17,366 acres (7,028 ha) in the Panamint Range, Inyo County, California. Access to the area is by State Route 190, approximately 45 miles (72.4 km) east of Lone Pine, California and 16 miles (26 km) southwest of Stovepipe Wells, California (fig. 1).

Jan 1, 1983

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By C. H. Riggs

This petroleum-engineering study of the Healdton oil field in Carter County, Okla., describes the geology and production history of that field and estimates the oil reserves that could be produced by efficient secondary-recovery methods. The Healdton field, in western Carter County approximately 20 miles west of Ardmore, Okla., was discovered in 1913 and was one of the early important oil-producing areas in the State. Although the volume of oil recovered from the Healdton sands has been comparatively high, studies show that a large reserve remains in the pressure-depleted sand, which can be recovered by efficient water-flood operations. In making this study of the Healdton-sand reservoir, the writers utilized many data already available in company and Government offices. Most of the fluid samples were collected by Bureau of Mines personnel and analyzed in the Bureau&apos;s laboratories at Bartlesville, Okla.; but other data, including logs, core analyses, and production records, were obtained from outside sources. These data were examined critically but were not verified, and possible errors in the original data may be reflected in the conclusions. In this study, attempts were made to consider only those aspects of the available information that would contribute to a clear and concise engineering report on the Healdton-sand reservoir. Other phases of the data, as well as those concerning associated reservoirs, were eliminated from consideration as being irrelevant to the particular problem. Cores and drill cuttings of the Healdton sands were analyzed and studied to determine the nature of the reservoir rocks. Analyses of samples of produced oil, water, and gas were studied to fix the different types, the limits of their occurrence, and the suitability of different waters for injection into the Healdton sands. Records of oil, gas, and water produced and of gas and water injected were studied to interpret the production behavior of the field and of certain individual leases. Theoretical calculations were made to predict the probable water-flood behavior and oil recovery, at constant water-injection rates, for individual sands on two leases.

Jan 1, 1953

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By A. Iannacchione

Major Hazard Risk Assessment (MHRA)1 is used to help prevent major hazards, e.g., fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, etc., from injuring miners. The structured process associated with MHRA helps to characterize the major hazards and evaluate engineering, management and work process factors that impact how a mine mitigates its highest risk. The National Institute for Occupational Safety and Health (NIOSH) studied the application of this technique to US mining conditions through a field-oriented pilot project. Risk assessment teams used in the pilot project were primarily composed of mining company personnel. Ten case studies were performed over a wide cross-section of mines. These mines were representative of the important mining commodities in the US minerals industry, i.e. coal, metal, non-metal, and aggregate. Also, the sizes of the mines ranged from small to large and were located across the country. The ten case studies demonstrate that most US mines have the capability to successfully implement an MHRA and that the MHRA methodology produced additional prevention controls and recovery measures to lessen the risk associated with a select population of major mining hazards. The basic ingredient for a successful MHRA is the desire to become more proactive in dealing with the risks associated with events that can cause multiple fatalities. A successful outcome is marked by a thorough examination of existing prevention controls and recovery measures. When pressed to consider more controls to further mitigate the risk, a well-staffed risk assessment team was able to identify additional controls. For these mining operations, it was important to add additional controls, even if they were not required by existing mining regulations, to lower the risks associated with the major hazards under consideration. If a mining operation is not willing to commit its best people to an MHRA or will not provide them with sufficient time to see the process through to its conclusion, the MHRA output may prove to be useless. Additionally, if a mining operation is not prepared to discuss its major hazards in an open and honest fashion and to present the findings of the risk assessment in a written report, the MHRA output will be unclear, and attempts to monitor or audit important controls may not be possible. A MHRA is most effective when the mining operation possesses 1) a proper understanding of its hazards, 2) experience with informal and basic-formal risk assessment techniques, 3) proper facilities, machinery and equipment, 4) suitable systems and procedures that represent industry Best Practice, 5) appropriate organizational support with adequate staff, communications and training, 6) a formal and thorough plan for emergency response, and 7) a safety risk management approach that is promoted and supported at all levels of the organization.

Jan 1, 2008

By Andrew M. Leszcykowski

This report represents the first comprehensive accounting of lode mining sites in the Sheep Mountain mining district, Custer County, Idaho. Twenty-one mine and prospect locations have been added to the Bureau&apos;s Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were checked and the updated information added to the data base. The district&apos;s deposits are mainly confined to metasedimentary xenoliths in granodiorite and quartz monzonite. Those deposits in the north and west parts of the district are lead-silver-zinc replacement veins in dominantly calcareous facies; those in the southern part of the district are polymetallic fissure-veins containing pyrite, chalcopyrite, arsenopyrite, galena, and sphalerite hosted by micaceous schist and phyllite. The dominant structural trend in the southern part of the district is northwesterly and on strike with major deposits in the adjacent Seafoam mining district.

Jan 1, 1983

By Russell J. Foster

In this Bureau of Mines report a selection process has identified 14 nonstockpiled materials (cesium, gallium, hafnium, indium, osmium, rhenium, rhodium, rubidium, ruthenium, scandium, selenium, tellurium, thallium, and zirconium) that are linked to the continuing evolution of high-technology fields such as electronics, catalysis, and energy, and that have limiting factors associated with domestic availability. A qualitative assessment of the "potential criticality" of these materials was made through a consideration of end uses, demand trends and forecasts, production, mineral reserves, byproduct status, alternative supply sources, substitution and conservation options, and recyclability.

Jan 1, 1988

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.&apos; Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation&apos;s coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960