Search Documents

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer's attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By H. A. Doerner

"The pure mineral chromite, FeO.Cr203, consists of ferrous and chromic oxides, chemically united in equal molecular proportions. Unfortunately, pure chromite as defined above appears to be a rare exception. In most chrome ores the mineral may be considered a combination of spinel, MgO.Al203, and chromite, with the latter predominating. The ratios between the four common constituents Fe0, Mg0, Cr203 and A203 vary greatly, and other minor constituents such as TiO2 and. Fe203 may also be present.In the mechanical concentration of chromite ores the maximum grade of concentrates that can be produced is thus limited by the composition of the chrome minerals present. Pure chromite contains 68 per cent Cr203, but the Cr203 content of the chrome minerals in commercial ores varies between 45 and 60 per cent and the average is not far from 55 per cent.Chromite is usually associated with serpentine. Other silicates, quartz, dolomite, magnetite, ilmenite and other iron Minerals are frequently present.The amenability of a chrome ore to concentration, depends upon the kind and amount of the various gangue minerals present and the amount .of crushing necessary to separate the chromite from them.A relatively small amount of chrome ore is concentrated by milling. In most cases the mine product is simply hand-sorted. Such chrome deposits as are known in the United. States can not be worked in this way on account of one or both of the following conditions: High cost of labor and finely disseminated impurities. There are, however, several deposits in the United States, Canada, and Alaska which may be able to compete with imported or by efficiently utilizing modern ore-dressing and milling methods."

Nov 1, 1930

By D. Harrington

The experience of the past 2 years has demonstrated clearly that mine explosions with heavy loss of life can be prevented. The investigations of the Safety Division of the United States Bureau of Mines disclose that during the fiscal year 1934 there were only 28 deaths from mine explosions in the United States, and during the fiscal year 1935 there were 54 deaths, a very favorable reduction when compared with an average death toll of 265 from this cause during the 20-year period prior to 1929. Although the frequency of occurrence of explosions has not decreased greatly during the past 7 years, there has been a marked decrease in severity, indicating that the coal-mining industry is taking more effective precautions to prevent the spread of explosions. A number of large coal-producing States, which in past years have experienced numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 5 years or even longer. A study of several hundred mine explosions occurring in the United States during the past 10 years or more indicates that the factors mainly responsible for these explosions are inadequate or defective ventilation and disregard of the hazards from explosive gas. Both of these factors are subject to control, and if controlled it is safe to say that deaths from explosions would be reduced to a negligible number as relatively few explosions are now initiated by dust.

Jan 1, 1936

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By W. A. McKinney

The segregation process consists of heating crushed oxidized or mixed oxide-sulfide copper are with a copper-volatilizing salt and carbonaceous material at about 750° C. to produce metallic copper which is recovered from the furnace calcines by conventional sulfide flotation. The Bureau of Mines made a number of bench-scale laboratory tests on two copper ores to determine the relative merits of using halogen salts, potassium chlorate, or various salt mixtures as volatilizing agents in segregation of the copper. Laboratory investigation of typical siliceous and calcareous oxidized ores revealed that sodium chloride was a better segregating agent than the other salts. Calcium chloride, magnesium chloride, sodium fluoride, or potassium chlorate gave nearly as good segregation as the sodium chloride on the siliceous ore. Segregation of the calcareous ore with calcium chloride was nearly as good as that obtained with sodium chloride, but inferior segregation resulted when magnesium chloride, sodium bromide, or potassium chlorate was employed. The use of sodium bromide or sodium iodide on the siliceous ore, and of sodium fluoride or sodium iodide on the calcareous are, gave appreciably poorer segregation than sodium chloride or the other salts. Other tests of the ores, using mixtures of sodium chloride and the other halogen salts or potassium chlorate, gave segregation approaching that obtained with sodium chloride.

Jan 1, 1962

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By S. R. Zimmerley, C. H. Schack

"INTRODUCTION The pilot-mill concentrator at Boulder City, which has a nominal capacity of 40 tons per day, was planned and built to investigate further the beneficiation of domestic manganese ores that have been concentrated successfully in the ore-dressing laboratory. As milling of manganese ores in general is a new field, it is necessary to prove the success of laboratory processes by means of large-scale operations employing standard milling equipment, and thus to obtain engineering and metallurgical data essential to designing and operation of full-scale concentrating mills.The first ore tested in the pilot plant was the Three Kids Annex manganese ore from the Las Vegas Wash area 15 miles southeast of Las Vegas, Nev. The deposit was worked for its high-grade ores during the First World War From 1930 to 1939, 4,500 feet of diamond drilling was completed by a private company. Diamond drilling started by the Bureau of Mines in November 1940 and completed in July 1941 aggregated 6,600 feet. Exploration by the private company and the Bureau outlined reserves of about 1,000,000 tons of ore assaying plus 28 percent manganese. A much larger tonnage of lower-grade ore also was outlined by the drilling.Because of its physical nature, the Three Kids Annex ore had long proved unamenable to concentration by ore-dressing methods. The ore is a mixture of manganese oxides (wad) filling the pores and to some extent replacing a silt composed of very fine grains of volcanic tuff, quartz, feldspars, other silicates, and clay. Some gypsum occurs as fillings along fracture planes. The ore is light and very porous. Upon wetting, it disintegrates into granular but friable particles and a large amount of slime. It is these characteristics that make the ore so difficult to concentrate."

Sep 1, 1947