Search Documents

By Yuhua Wang, Haitao Zheng, Guangli Zhu, Yuehao Zhao, Fushun Yu, Dongfang Lu

"Spodumene, feldspar and quartz possess similar surface properties, which make the difficult to separate spodumene from other silicate minerals by flotation. The differences of crystal structure, surface property and floatability of three minerals were studied by various technical means. The results show that Li-O and Al-O bonds in spodumene structure are not strong and easy to be broken. However, Al-O and Si-O bonds in feldspar and Si-O bond in quartz are very strong and not easy to be broken. High contents of Al and Li on spodumene surface were found by XPS measurements, which is benefit for the adsorption of anionic collector. The surface energies of main cleavage planes of spodumene (110), feldspar (001) and quartz (001) are 1.88 J/m2, 2.97J/m2 and 2.68J/m2, respectively. Hence, the exposed surfaces of feldspar and quartz are not saturated and easy to adsorb OH- ions from solution and cause the lower IEP than spodumene. The contact angles of three minerals in water are lower than 16º, suggesting that the hydrophilicity of three minerals is high, and the order of hydrophilicity is quartz > feldspar >spodumene. Correspondingly, contact angles and flotation recoveries of spodumene are bigger than that of feldspar and quartz in presence of a combined anionic and cationic collector named YOA.INTRODUCTION Flotation technology plays most important role for the recovery of spodumene from pegmatite ore. Generally, spodumene with fresh surface is easy to be floated using soap and oleic acid as collector, and the best flotation pH range is 4.0 to 9.0. However, the flotability of spodumene will become worse when its surface was polluted by slime which produced by the weathering of spodumene and other silicates (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015). In addition, the species of Ca2+, Fe3+, Mg2+ and other metal ions in pulp can not only activate the flotation of spodumene, but also the activation of gangue minerals, and then the flotation selectivity of spodumene from gangue minerals became wores (Wang and Yu 2007; Yu et al. 2014). In order to eliminate the negative effects of slime and metal ions on the flotation of spoddumene, the desliming and long time scrubbing with the addition of NaOH and Na2CO3 were adopted. Usually, NaOH shows the activation for spodumene flotation, and the recovery of spodumene increases with the increase of NaOH dosage. Na2CO3 can eliminate the non selective activation of Ca2+, Fe3+, Mg2+ ions in the pulp, and the concentrate grade of spodumene increases with the increase of Na2CO3 dosage. Anionic collectors such as chelants, hydroxamic acid, oxidized paraffin soap, naphthenic acid and oleic acid were widely used for the flotation of spodumene (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015)."

Jan 1, 2018

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014

By K. Lillkung

The use of secondary sources has become a very attractive option in the production of platinum group metals as the demand for these metals has increased. One of the promising sources are the spent catalysts, which provide an attractive source as they have relatively high metal content compared with the ores where the metal is originally extracted from. The concentration of platinum group metals in catalytic converters is in the range of 0.1-1 mg/g as the concentration in ores is usually less than 10 ppm. Aqueous chloride solutions are claimed to be a cost effective way in which platinum group metals can be brought into solution and concentrated. In this work the effect of different parameters on the dissolution rates of Pt, Pd and Rh were investigated. The parameters investigated were the Cl- concentration, the temperature and applied potential. Chloride concentrations used were 62.5, 90, 125 and 250 g/l. Temperatures were 25, 40, 60, 80 and 94°C. Potentials were 950, 1050, 1150 and 1250 mV vs. SCE for Pt and Rh and 380, 410, 440 and 470 mV vs. SCE for Pd. Dissolution rates were calculated from the current densities determined by potentiostatic measurements. Thin wire electrodes were used in the measurements. As expected, higher temperature, higher potential and higher chloride content generally increasedthe dissolution rate. However, the effect was nonlinear and slightly different for different metals. The results show that strongly oxidizing conditions are needed in order to achieve reasonable dissolution rates. With the highest chloride content and at potential of 1250 mV vs. SCE and 94°C the dissolution rate of Pt was nearly 1 mm/h, whereas in similar conditions Rh achieved a rate of only nearly 100 µm/h. Similarly, with the highest chloride content and at potential of 470 mV vs. SCE at 94 °C the dissolution rate of Pd was nearly 1 mm/h. Keywords: Pt, Pd, Rh, redox potential

Sep 1, 2012

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By A. Deepatana

This study compares the use of an aminophosphonate chelating resin Purolite S950 and a sulphonic acid strong cation exchange resin Purolite C160H to recover nickel and cobalt from the synthetic bioleach solutions. Batch adsorption of metal citrate is performed as a function of metal citrate concentration (15~2000 mg/L) and solution pH (0.01M and 0.1M citric acid). The adsorption mechanism as inferred from the fit to Langmuir (LM), Freundlich (FM) and Redlich-Peterson (RP) models demonstrates that nickel citrate adsorbed onto C160H appears monolayer in comparison to that adsorbed onto S950 exists multilayer. In contrast, cobalt citrate adsorption onto both C160H and S950 agrees with the LM model. The results have shown that loading capacities of nickel and cobalt citrate onto C160H are 60 and 65 mg/g whereas those observed onto S950 are 16mg/g and 6 mg/g respectively. These are achieved in metal citrate prepared in 0.1 M citric acid. Resin regeneration is conducted in using 2 M nitric acid solution. The results show high efficiency of nickel and cobalt citrate elution from Purolite C160H. Findings from this study suggest Purolite C160H is a suitable adsorbent for recovering nickel and cobalt from bioleaching solutions.

Jan 1, 2014

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012