Search Documents

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By David Sherwood

The paper has been prepared as the basis for the 2008 John Mitchell Memorial Lecture. It reviews major developments in ground engineering over the last 20 years, not from the point of view of technical processes, but from the drivers that have driven these developments and the needs that they have met. It concludes with a glimpse into the future and suggests to where current trends will probably lead us. By its nature such a review is closely aligned with personal experience and it relies heavily on case histories largely from within the writer?s own experience over that period.

Jan 1, 2008

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Braxton P. Erbe, Douglas C. Brunot

A variety of systems and techniques exist to support deep excavations where sloping is not feasible. This paper will explore an example project involving the use of pre-engineered hydraulic bracing systems to support sheet pile walls. Challenges on site that drove the final design include a high water table, irregular excavation geometry, and underground obstructions. The hydraulic system, connected by pins and not requiring welds, allowed for quick deployment and the modularity to change as required due to unforeseen site conditions.

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Prof. Dr. -Ing. habil. Sascha Henke, Johannes Beck

The growth of Building Information Modeling (BIM) during recent years opens possibilities for integrating new digitally driven design approaches. While parametric design and algorithmic design slowly gains popularity in numerous ACE-applications, e.g. bridge design, it is rarely used by geotechnical professionals. This article presents an approach for implementation of parametric design in the BIM-based geotechnical design process. The methodology is applied to pile design and enables a real time design analysis according to DIN EN 1997-1 and EA-Pfähle 2012 considering boundary conditions such as pile position and layout, pile geometry, soil stratification and soil properties. By using intelligent attributes and scripts to control, calculate and assign them, the design analysis is directly executed in the BIM-software environment, in this case Autodesk Revit with Dynamo. This BIM integrated design approach allows multi-criteria evaluations of pile designs using aspects such as costs, environmental impact or constructability in addition to the commonly examined structural analysis criteria. As the proposed models are fully parametric, generative optimization algorithms can be applied to identify the ideal design for the entirety and each of the piles. Finally, the potential and limits of this methodology with respect to modeling, analysis, simulation and optimization are discussed.

May 1, 2022

By Christian Leble, Dr. -Ing. Jakob Vogelsang, Dr. -Ing. Oksana Solt, Dipl. -Ing. Joachim Meier, Dr. -Ing. Wolfgang Orth

In the course of closing the gap between the Brandenburg Gate and Alexanderplatz, the Museum Island station was built by Implenia Construction GmbH. The tunneling for the platform hall took place on a length of about 106 m (347 ft) under the protection of a major ground freezing measure and crossed the Spree canal as well as the listed castle bridge. The approximately 20,000 m³ (4.54 E+06 US gal dry) frozen mass lay mainly in the Berlin sands. In order to ensure safe tunnelling and to protect the adjacent buildings, the planners had defined requirements for the mean freezing temperature and thickness of the frozen mass. For a reliable conclusion on the dimensions of the frozen mass, we used innovative temperature sensors as well as the new, web-based 3D measurement visualization and the associated site-specific evaluation software. The largely automated evaluation enabled a quick and reproducible determination of the temperature distribution in the frozen soil and its thickness in the relevant cross-sectional areas. The measurements were validated by thermal calculations using the Finite-Element-Method. Thus, an objective and clear assessment basis was available to ensure rapid coordination between stakeholders. The evaluations provide new insights into the temperature influences from tunneling, the application of shotcrete and the concreting of the inner shell. The newly implemented active thawing system is also an interesting innovation.

May 1, 2022

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Jorj Osterberg

550 load tests of up to 150 MN have been completed on driven and bored piles using the Osterberg Load Cell. Because the test measures side shear and end bearing separately, much can be learned about the forces on the pile as it is loaded to ultimate capacity. At working loads side shear almost always far exceeds end bearing, with the distribution of shear and bearing greatly affected by disturbance occurring during drilling operations. Since much less movement is required to mobilize side shear than end bearing, most of the bearing develops after the working load is exceeded. Thus with insufficient bottom cleaning, safety against excessive settlement can be considerably reduced. Improved methods of drilling, hole cleaning, rebar cage installation and concrete placement are discussed. For rock socket piles it has been found that the ultimate test load far exceeds the working loads in most cases. This is almost always due to greater penetration into the rock than is required for adequate safety against excessive settlement. Factors affecting rock socket capacity are discussed. Increase of side shear and ultimate capacity with time is discussed. Case histories for driven and bored piles in soil and rock sockets are described.

Jan 1, 2001

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy"

Jan 1, 2017