Search Documents

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By Fabian Kirsch

Cyclic behaviour of axially loaded piles has been an issue since studies revealed that the capability to transfer skin friction into the ground is highly depending on the level and the number of load cycles the pile is subjected. It has been shown that degradation of skin friction due to axial cyclic loading leads to accumulating displacements and a severe reduction in pile capacity. In Germany the DIN 1054 as well as the Recommendations of the Working Group 2.1 ?Piles? of the German Geotechnical Society (EA-Pfähle) require the consideration of cyclic loading for the assessment of both the displacements and the capacity. Up to now no broadly accepted design method exists, which enables the engineer to give a reliable judgement on the pile capacity under axial cyclic loading and the displacements respectively. Instead numerous design charts make it possible to distinguish between stable and instable loading levels in order to ensure a design on the safe side. A newly developed design approach based on engineering models is presented which delivers a calculation algorithm for the remaining axial pile capacity after a defined number of load cycles to allow for the analysis of stability of the foundation. Furthermore the computation of accumulating displacements is made possible. The results are verified with pile load tests undertaken at Dunkirk, France and showed that the axial capacity after cyclic loading calculated with the newly developed design approach predicts actual capacity with an accuracy of ±20%.

Jan 1, 2011

By James S. Graham

Research at the University of Colorado on southern pine and Douglas-fir piling has determined that the existing building code design stress values of 1200 psi and 1250 psi, as determined by ASTM D-2899, are substantiated; but testing procedures should be revised. All full size piling tests should be standardized at 1/d ratios of 2:1, or confined tests performed. Also, it has been determined that theoretical design values for timber piling should not be based on the lumber criteria of D-245 and D-2555, but instead should follow the pattern set by engineers in the utility industry for timber poles, in accordance with ANSI 05.1.

Jan 1, 1986

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft's capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By Virendra Singh

The load settlement behaviour of single pile or pile group may be obtained using computer based methods such as the finite or boundary element techniques. An alternative method of obtaining the vertical soil stresses adjacent to the Pile is presented Based on calculated stresses consolidation settlement for Piles foundation is obtained. This approach may be computationally more attractive than the more general finite or boundary element techniques.

Jan 1, 1996

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

Jan 1, 1984

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By Louis Donolo

New buildings in today's urban environment, especially in down-town areas, invariably involve the construction of multiple level basements. Used for parking, storage and commercial space, these underground structures normally extend 30 to 50' and more below grade and, to make optimum use of expensive land, they usually occupy the full site right up to street/sidewalk and property lines. SOIL SUPPORT SOLUTIONS Building these basements requires vertical excavation, and consequently, a temporary soil support system which will eventually be replaced by the permanent foundation walls of the structure.

Jan 1, 1987

By Shane Baker

Cementation Foundations Skanska Ltd encountered many significant challenges in designing and constructing the foundations for the LNG (Liquefied Natural Gas) tanks and associated structures at the Isle of Grain, Kent, UK. With LNG cargo ship levels fixed by the adjacent English Channel, the platform could not exceed critical thickness in order to achieve final grade level, so a safe and efficient working platform for construction equipment on extremely poor alluvial soils was designed and installed. The detailed pile design also required particular analysis of the pile group behaviour and considered seismic load cases not usually associated with UK pile design. Continuous flight auger (CFA) piles were the chosen foundation solution and design was verified through preliminary and working pile tests both axially and horizontally. Contaminated land and existing foundations from a previous oil terminal meant that removal of spoil was extremely costly so specific measures were taken to minimise the off-site disposal. The management of a package of general Civil Engineering in addition to the piling scope, coupled with an unrelenting production program has forced a raising of the bar for this foundation technique.

Jan 1, 2006

By Dawn C. Tattle

[ ] Panoramic View of Completed Facade Supports The following case history describes the installation of earth retention systems, historical facade supports and structural caissons by Anchor Shoring & Caissons Ltd. at the Air Canada Centre/Raptors Stadium Project in Toronto, Ontario, Canada. The Air Canada Centre/Raptors Stadium project includes a 140,000 square foot office tower, a 20,000 seat basketball arena and their support facilities. The arena within the complex will also have the ability to host hockey, ice shows, concerts and family events.

Jan 1, 1997

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010