Search Documents

By W. H. Craig

Techniques have been developed for installing model piles into beds of soil under high sustained acceleration levels aboard a centrifuge. These piles have been subjected to static and/or cyclic lateral loading in order to assess their performance and provide a data base for assessment of various design techniques for laterally-loaded single piles. From measured bending moment profiles the so-called 'p-y' curves have been deduced using fifth order splines for curve fitting, followed by subsequent differentiation and integration. The results show some divergence from the predictions of the semi-empirical designs, but these latter are generally found to be acceptable.

Jan 1, 2010

By A. Le Kouby

We present in this paper the results of a parametric study carried out in a calibration chamber on instrumented model piles. The aim is to point out group effect on piles within a group through their resulting shaft friction and tip resistance. The methodology relies on the study of the influence of adjacent piles on a "reference" pile. The soil used is a silica sand (Fontainebleau sand). The influence of parameters like pile spacing, number of piles and installation order are evaluated. The results show a positive effect on shaft friction of the group effect and a negative effect on tip resistance. Efficiency factors are defined in order to have a better view on the parameters influencing the response of the pile within a group.

Jan 1, 2006

By Yong Jingrong

Based on the results of several test socketed piles in Sichuan, the mechanism of the deformation for a loaded socketed piles is investigated, and the concept of the socketed effect is proposed. The bearing capacity and settlement of socketed pile are controlled directly by socketed effect, that is an important mark different from the other types of cast-in-situ piles. According to the analysis of this effect and factors interferring it, their roles are discussed with the results of test piles. In order to increase the bearing capacity of piles, the ways and methods enhancing socketed effect are recommended.

Jan 1, 1991

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Gary T. Brill

In the presentation, the development and new applications of the jet grouting technique in the North America are briefly introduced at first and followed by the outline and advantages of Jet Grouting. Several recent projects for jet grouting are presented in which the applications to underpinning and excavation support, foundation, groundwater barrier and seismic stabilization are briefly discussed.

Feb 10, 2003

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005

By Kento Miyamoto, Kazuki Imamura, Takayuki Tanaka

"Global economic development has drastically increased energy consumption in various fields, and CO2 emissions, which are a prime cause of global warming, have continued to increase. Therefore, measures for reduction of the load on the environment have been taken in various areas. Energy improvements of various types of work vessels used for offshore construction might be expected to greatly reduce consumption of fossil fuel, because many of these vessels are larger than land construction machinery and consume large amounts of fuel, which will lead to effective use of resources and alleviation of the load on the environment. However, such efforts are unusual because renewal or newbuilding of work vessels is rare. We developed a work-vessel hybrid energy system based on fuel-saving technology and use of natural energy to promote reduction of CO2 emissions for a large deep mixing barge in 2010. We developed an Automated Generator Start-Stop System, which automatically controls the number of active generators according to power demand during ground-improving work of the deep mixing barge in 2012, thus further improving the work-vessel hybrid energy system. These systems are introduced here.INTRODUCTIONIn recent years, CO2 emission, which is one of the factors of the Global Warming has been increasing. According to the report by National Institute for the Environmental Studies in Japan (2014), CO2 emission in Japan has amounted to 1,276 million tons. The industrial sector in the total emission becomes 500 million tons that is equivalent to 39%. Meanwhile, the offshore Deep Mixing Method requires work vessels mounted with a large power plant (Fig. 1). In sea ground boring, very large load acts on the deep mixing machine, and the large power is required, which results in the increase in CO2 emission. To achieve eco-friendly marine construction, the work-vessel hybrid energy system was developed. Table 1 shows specifications of the deep mixing barge with the work-vessel hybrid energy system."

Jan 1, 2015

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By K. Ronald Chapman, Claus Ludwig, Doug Jenevein

"In the spring of 2005 Schnabel Foundation Company completed a $15.2 million Design/Build subcontract to underpin 11 structures, and provide 202,800 square feet of earth retention for the Reno Transportation Rail Access Corridor (ReTRAC) project in Reno, Nevada. Schnabel’s work was part of a Design/Build contract to depress a railroad alignment through downtown Reno. The depressed section was 2.2 miles long, 54 ft wide, and up to 35 ft deep (3.5 km long, 16.5m wide and up to 10.7m deep). The trench structure was required to be watertight. SUBCONTRACT WORK OVERVIEWEleven buildings along the track alignment required underpinning. Three types of underpinning were used, designated Type 1, Type 2 and Type 3.At four buildings the trench retaining walls were to be located directly under the exterior footings. This alignment eliminated traditional underpinning and cut-off wall techniques that could normally be used to support structures. Type 1 underpinning was used at these buildings. This underpinning system consisted of a combination of permeation grouting, hand-dug piers, and permanent tiebacks. This underpinning system became the new watertight trench walls.Five buildings were located a few feet behind the trench walls, and their exterior walls were supported by continuous footings. Type 2 micropile/pile cap underpinning (patent pending) was used to support these buildings.The remaining two buildings were also located a few feet behind the trench walls, but they had column footings along the exterior walls. At these structures traditional micropile underpinning was provided through the existing footings. This is described as Type 3 underpinning.Temporary earth retention was required on both sides of the trench along most of the alignment. This shoring supported frontage roads, private property and surcharge from the temporary railroad shoofly running parallel to one side of the trench.SUBSURFACE CONDITIONSThe soil along the trench alignment consisted of river outwash deposits. The top 2 to 18 feet (0.6m to 5.5m) generally consisted of flood plain silt and sand deposits, or fine-grained fills. These fine-grained soils are underlain by the Tahoe Outwash Formation which consists of interbedded layers of sand; sand and gravel; and sand, gravel, cobbles and boulders. Some of these layers encountered during construction consisted of 30 to 50 percent cobbles and boulders, with some boulders up to eight feet in diameter.A major challenge to the design and construction of the trench structures and the underpinning was the ground water table which was 10 feet (3m) above subgrade in the deepest portions of the trench. Based on specification restrictions, temporary and permanent dewatering was not feasible. As a result, the selected design and construction methods had to consider three water conditions: the anticipated groundwater level during construction (CGW), the groundwater level for permanent design (DGW), and an additional special design condition with water at street grade."

Jan 1, 2006

By Masaaki Terashi

The machine for the hybrid method called JACSMAN is ordinarily a dual shaft machine. Each shaft has augers at three different levels and nozzles for jetting at two different levels. The distance between two shafts may be changed according to the particular requirements. Figure 4 shows single shaft and a treated soil column created by the method. The diameter of the auger is 1.0 m. As the jetting nozzles locate at the periphery of the auger, jetting can achieve the additional treated soil column beyond the diameter of the auger. The diameter of the jetting improvement is fixed at 2.3 m.

Feb 10, 2003

By Anand J. Puppala

This paper provides information on various evaluation studies conducted to assess the CPT based interpretation methods. Salient findings from these evaluations are summarized. Additionally, a comprehensive evaluation study on both LCPC and European methods was performed on twenty-four driven piles selected from four different states. This evaluation showed that the LCPC method predictions are close to measured pile capacities. The European method provided good predictions for driven steel piles. Overall, both methods' predictions show high values of coefficients of variations, which are in agreement with other studies. Overestimation of driven concrete pile capacities is attributed to large estimations of unit point resistance. Suggestions to consider appropriate CPT based pile capacity interpretation methods are presented.

Jan 1, 2002

By K. C. Foye

Use of load and resistance factor design (LRFD) of foundations is growing, from offshore applications to bridge applications and beyond. The development of load and resistance factors for design has traditionally relied on calibration to traditional factors of safety. This technique, however, offers little insight into the challenges of pile design. This paper discusses an approach to LRFD factor development that seeks to isolate the various sources of design uncertainty. Using this approach, reliability analysis is used to develop resistance factors for the design of driven pipe piles in sand. These findings shed light on many aspects of the ongoing discussion of how LRFD can be successfully applied to pile design.

Jan 1, 2008

By Dinesh R. Katti

Caissons which are locally known as well foundations, which may very in diameter from 30 m to more than 30 m and in majority of the cases having depth to diameter ratio between 1 to 1.5, are normally used to support piers of long span bridges or tall structures, which transmit high magnitude of axial load, horizontal thrust and moment. On the basis of depth to diameter ratio the foundation system appears to fall in the category of shallow foundations but due to deep excavation, it is observed that part of the moment acting on the caisson is shared by due the sides due to development of passive resistance. The problem is statically indeterminate and three dimensional in nature. To ascertain the various parameters needed for design, such as moment shared by base and sides, horizontal and vertical displacement and tilt, and base and side contact pressure diagrams need to be obtained from nondimensional relations of parameters with respect to D/B ratio derived from large scale model studies conducted by Katti etal at IIT, Bombay under MOT Project between 1976 and 1988 and later on at UNEECS. On the basis of above data on attempt is made to put forward guide lines for selection of parameters for design of caisson foundations / well for following cases for opening us some discussion. The cases are cohesive soil at the side and cohesive soil, or sand or soft rock or hard rock at the base.

Jan 1, 1996

By Andrew Budek

Reinforced concrete piles are used to carry foundation loads through considerable depths of soil to provide superstructure stability under gravity loads and lateral forces. The creation of cast-in-place (or cast-in-drilled-hole, i.e., CIDH) piles begins with the auger-drilling of a hole of the appropriate depth, into which a cage of reinforcing steel is placed (the cage length is generally equal to the depth of the hole, a construction joint being used to connect the in-ground pile with the superstructure). The pile is then finished by casting with concrete, and the superstructure then appended. The superstructure may either be a column (denoting the structure a pile-column), a column and cap beam, or a footing. Typical pile-column configurations are shown in Fig. 1 (a CIDH pile used in a footing would be similar in overall configuration to Fig. 1(b), with H=0). CIDH piles are well-suited for alluvial soil profiles with a deep water table; such conditions generally allow the auguring of a clean and regular hole.

Jan 1, 2007

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Goudschaal Mark R.

"The Museum of Science and Industry U-505 Submarine Relocation project in Chicago, IL consisted of building an underground reinforced concrete vault (37' deep) for the Museum's new U-505 exhibit. This WWII submarine was captured in 1944, had been located outdoors at the Museum since 1954 and was lowered into its new exhibit area in 2004. A unique combination of earth retention, water cut-off and underpinning systems allowed a forty-two foot (42') deep excavation underneath th is historic museum. The museum - originally built in 1893 for the Chicago World's Fair - was closely monitored for building movements throughout construction. The underpinning systems, construction activities and monitoring results are presented herein. IntroductionThe historic U-505 German submarine at the Museum of Science & Industry was restored, moved approximately 1,000' and then lowered into its new indoor home (Figures 1, 2 and 3). The new underground exhibit opened this year celebrating the 61st anniversary of the German submarine's capture on June 4, 1944. On this historic day, Captain Daniel V. Gallery, a Chicago native, led the Navy in the siege of this submarine near the coast of Africa. This U-boat was the only German sub captured by the United States Navy in WWII and the Enigma machines, codebooks and publications recovered from the sub helped the war effort."

Jan 1, 2005