Search Documents

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

By S. Suzuki, C. Tokoro, S. Owada, T. Sakakibara

Acid mine drainage (AMD) has been actively treated by neutralization from about 80 abandoned or closed mines in Japan. More efficient and cost effective treatment processes has been demanded for AMD due to the government investment of billions of yen every year to protect the environment from these discharges. In this study, quantitative modeling was conducted for actual AMD to predict pH or residual concentration of toxic elements after neutralization/co-precipitation process. Simple chemical equilibrium calculation was not adequate for quantitative prediction of pH after neutralization, because residual concentration of major elements of AMD, such as Fe or Si, could not be quantitatively calculated. When oxidation rate of Fe(II) to Fe(III) and precipitation rate of kaolinite were added to the model, quantitative prediction of pH and Fe or Si concentration was achieved. Surface complexation at the interface between hydroxide such as ferrihydrite or aluminum hydroxide and AMD was the most important mechanism for removal of dilute toxic ions. When surface complexation model at the interface of ferrihydrite was added to the model, residual As (V) and Pb (II) concentration after neutralization/coprecipitation process was successfully calculated. On the other hand, surface complezation model of aluminum hydroxide was also necessary for quantitative prediction of residual Zn(II) concentration after neutralization/co-precipitation process.

Jan 1, 2014

By N. Plint, M. Potgieter

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By E. L. Day

"In the early 1930s during the course of test work with a simple gold ore, it was evident that the time required to dissolve the gold by cyanidation was very much longer than should have been needed theoretically for the maximum size gold particles in the ore, A similar conclusion appeared to be valid for other gold ores. In a cyanidation system there are many factors which can influence the dissolution rate of gold, and a decision was made to investigate the more obvious variables, because a literature survey at the time showed that with the exception of the work of Yamazarki on the dissolution of silver in cyanide solution, virtually no attention had been given to this subject, Our work was not reported because the intention was to do this on completion of the Study, but owing to the demands on the Section's personnel for other work the investigation was never completed. Although other investigators have since studied the problem, the methods which we adopted and some of the conclusions may be of interest to metallurgists concerned with gold ore treatment.Form of GoldExperiments with gold ores were not possible because of the number of uncontrollable variables present in a gold ore-cyanidation system, therefore pure metal and reagents were used. Initially some experiments were carried out with gold leaf, but it was soon apparent that metal in this form was unsuitable because the uneven thickness of the leaf caused it to break up into pieces and. there was difficulty in determining precisely when complete dissolution had taken place, Numerous factors both expected and unexpected were found to influence considerably the results and much experimental work was necessary to establish the procedures which were finally adopted, Experiments were carried out with gold in the form of foil, wire, rings and sols. Finally, gold foil in the form of cylinders was adopted for most of the experiments although some work with gold in the sol form was included in the programme. Also some experin1ents were carried out with a gold ore to see if effects which were obtained with sodium chloride on gold sols were applicable to gold ores."

Jan 1, 1967

By M. Kaya, A. R. Laplante

"Since the beginning of eighties the use of flotation columns has surged in Canada and abroad; the metallurgical superiority of columns over mechanical cells is in great part due to froth washing, which ensures higher gangue rejection and selectivity. Can wash water, which has proven so beneficial, be used in mechanical cells? Although froth washing technology was widely implemented in Soviet plants for bi tuminuous coal, and alusite, powellite, scheelite, molybdenite, etc. more than 25 years, it has been neglected in the western world. Published data suggest 10 to 15~ increases in grade and/or recovery with wash water in mechanical cells (Klassen and Mokrousov, 1963). There are at least three wash water plant applications in Zaire, Chile, and Canada, but little, if any, published information is available. This research work, which is the first extensive fundamental study related to froth washing in mechanical cells, attempts to answer the questions of how, how much, and where should wash water be added.This project was undertaken in three stages:1. Bench-scale laboratory tests with a 6.5 L Denver cell at McGill using a silica flour and a slime reject from Niobec (St.Honor6).2. Pilot-plant scale tests with a 65 L Denver cell at McGill using the silica flour and a complex Cu-Ni sulphide ore from the Strathcona mill of Falconbridge.3. Plant-scale tests with a bank of 2800 L Denver cells at Falconbridge Ltd. for complex Cu-Ni sulphide ore and Eastmaque Gold Mines Ltd. for Au tailing reclaimation."

Jan 1, 1989

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By P. C. Richards

"Future Integrated Gasification Combined Cycle (IGCC) power plants will have superior environmental performance and unmatched efficiency.The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an IGCC plant. SCGP flexibility has been demonstrated for feeds ranging from bituminous coals to lignites and petroleum coke, and the process is ideally suited for combined cycle power generation, resulting in efficiencies of 42% to 46% (LHV).In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology is being built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N. V. Sep). The plant is scheduled to start up in 1993. IntroductionBasic ConceptShell's experience with gasification dates back to the 1950s, when the first Shell Gasification Process was commissioned with oil as feedstock. There are now over 140 SGP gasifiers licensed. The experience gained on oil gasification provided a firm theoretical and practical base for the start of coal gasification process development in 1972.At that time, there were serious concerns about the future availability and price of crude oil. Coal gasification (making carbon monoxide and hydrogen by the partial oxidation of coal) was considered to be an important option for refinery applications, because the synthesis gas (syngas) produced can be used as:• a chemical feedstock for making transportation fuels and chemicals;• a source of hydrogen (making use of the water gas shift reaction) for upgrading petroleum products; and• a fuel for heating process streams and/or generating electricity."

Jan 1, 1994

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By Yuhua Wang, Wei Sun, Dongfang Lu, Yuehua Hu, Tao Jiang

"With the continuous depletion of high-grade tungsten ores, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and use of toxic collectors.The aim of this study was to develop an environment-friendly processing flowsheet, which was used for beneficiation of low-grade tungsten ore containing 0.45% WO3 from New Brunswick in Canada, and the content of arsenic is 0.68% in this materials. The objective of beneficiation studied was to obtain a concentration containing 60% WO3 with less than 0.5% of arsenic under the condition without any flotation reagents. In this environment-friendly processing flowsheet, magnetic separation technology, classification and gravity separation technology were combined and employed. Firstly, magnetic separation was employed for the first pre-concentration process, over 95% of the feed was rejected as the final tailings, meanwhile, over 85% of arsenic minerals were removed with tailings. Secondly, gravity separation tests were employed on the classified magnetic pre-concentrate in the second pre-concentration process, a second pre-concentrate with WO3 grade of 54.32% and As grade of 5.41% was obtained. Finally, two stage magnetic cleaning were conducted on the second pre-concentrate for upgrading the second pre-concentrate, the mostly arsenic and gangues were removed from the second pre-concentrate. Finally, this novel processing achieved an effective recovery of fine wolframite from low grade tungsten ore with high arsenic. A concentrate with WO3 grade of 64.81% were obtained in new opened processing flowsheet, and As grade was less than of 0.5% in this concentrate. Furthermore, remarkable feature of this processing flowsheet is environment-friendly due to avoid using the toxic flotation reagents during the whole mineral processing.INTRODUCTIONTungsten is an essential metal and is the most widely used in industrial production such as national defense, electro-mechanical products, textile and leather sectors (Srivastava et al., 2000). Wolframite and scheelite are the main mineral sources of tungsten metal. With the continuous depletion of high-grade tungsten ores and the increasing demand for tungsten alloy, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and heavy use of toxic collectors."

Jan 1, 2016

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By S. A. Kenzap

This paper provides an overview and discussion of key aspects of operating risk valuation in underground metal mining systems, with impact on project economics, using stochastic computer modelling in Discounted Cash Flow (DCF) analysis. Mine operating risk classification and assessment for ground, equipment and scheduling aspects are presented with an overview of available risk valuation tools that have been developed in engineering disciplines. The classification is organized by keeping in perspective the mine design needs and constraints, as well as the potential economic impact that operating problems can have on an underground development and production system. These sources of cost, revenue and time delays are tabulated to enable the hierarchization of potentially hazardous unplanned events occurring during the mining project life cycle. In complex technological systems, like the underground mining systems, the decision-making process involve a wide range of uncertainties, and often this is based on subjective and qualitative expert evaluations. Whether a qualitative or quantitative analysis is conducted, it is often the case that the probability of a certain project parameter value needs to be estimated. This requires use of methods and techniques to handle subjective, qualitative measures and to combine them with quantitative stochastic modelling in order to evaluate mine operations-related issues on DCF economic performance measure parameters. Links are established between decision making and the risk-based mine planning process for evaluation of design alternatives, with emphasis on the need of introducing flexibility in mine design. Finally, challenges of risk-based mine planning and design implementations are discussed and the call for an integrated risk-based real options systems valuation (ROV) ?in? projects analysis is made.

Aug 1, 2013

By S. Timbillah, R. LaDouceur, C. A. Young

A low carbon-chain trithiocarbonate ((NaOOC)CH2SCSSNa), known as Orfom® D8, was tested as an organic depressant in the differential flotation separation of chalcopyrite and molybdenite in the presence of sodium isopropyl xanthate (SIPX) or potassium ethyl xanthate (KEX). Flotation studies show that Orfom® D8 depressed chalcopyrite while molybdenite remained floatable. A study of the mechanism of adsorption indicated that Orfom® D8 adsorbs on chalcopyrite through its trithiol (CS -) functional group via both chemisorption and Orfom® D8-metal complexation. The Orfom® D8 depressant is selective and does not form any Orfom® D8-molybdenite bonds. Thus, the combination of the depressant in the presence of either collectors depressed the chalcopyrite and floated the molybdenite. Fundamental parameters of the Orfom® D8 including pKa determination as well as possible decomposition products of the depressant are reported. This study includes an economic case illustrating why using Orfom® D8 can be beneficial. INTRODUCTION Depressants are incorporated in mineral flotation units in the minerals processing industry to make or keep certain minerals selectively hydrophilic. Most reagents used are inorganic and include, for instance, sodium hydrosulphide (NaHS) which is the major reagent used for depressing sulphide minerals, particularly those containing copper, iron and lead. However, the issues with its use include high toxicity, tendency to explode, strong odour, and high consumption due to required high dosages as well as its tendency to oxidise in air. The latter can be overcome by conducting flotation in inert atmosphere such as nitrogen and recycling of the flotation process water. The use of more novel depressants that are essentially organic including homopolar reagents with hydrophilic functional groups on both ends of its structure adsorb onto a target mineral surface with one polar end, the other polar end orients into the bulk solution making the surface hydrophilic and thus, ensuring that the desired mineral does not float. The stringent environmental and safety regulations being implemented in recent times mean that the search for more environmentally friendly chemical reagents is a must have. The use of organic depressants for flotation systems such as Cu-Mo sulfide bulk concentrates has become increasingly important because of the health, safety and environmental issues surrounding the use of inorganic depressants. Nagaraj et al. (1983) investigated the Cu-Mo sulphide flotation system using a structure-activity study of depressants. They found that a major advantage of organic depressants is the ability to tailor-make organic molecules to suit many requirements and thus, eliminate the guess work approach that was predominant in the industry.

Jan 1, 2019

By J. Elbrond

"This paper describes qualitatively the progressive are losses and rock dilution in a mining project from the geological modelling to and including the concentration. A simple theoretical model of the net present value of a deposit, assuming a log-normal grade frequency function, is used to find the pair of decisions on rate of production and cut-off grade, which maximizes the net present value. Various degrees of ore losses and rock dilution are then applied on this optimum, and the resulting decreasing net present values are calculated, as well as the increasing cost of metal and the increasing metal losses as a function of are losses and rock dilution.IntroductionDue to a variety of uncertainties, to inevitable lack of precision in deposit estimation and in mine planning, and due to production constraints, ore losses and rock dilution occur throughout the many phases of a mining project. The phases range from the geological definition of the orebody, over the cut-off grade optimization and decision, over the design of the mining method and the actual mining to the ore dressing, where the final loss of valuable ore into the tailings occurs. Quantification of ore losses and rock dilution are mostly difficult if not simply impossible to obtain. At the end-phase an estimate of the total dilution may be obtained with some degree of precision by observations of the amounts and analysis of concentrate and tailings. It is much more difficult to estimate the total ore losses because the uncertainty of the geological modelling in the initial phase and in the mining phase is very difficult to quantify, despite the use of geostatistics for grade estimation.Many attempts at quantification of ore losses and rock dilution have been made and some examples are shown in Table I. Although they differ widely from each other, it is obvious from these figures that ore losses and rock dilution are significant and have considerable effects on the economical results of a mining operation. Life length, net present value, cost of producing metal and the loss of metal are all affected."

Jan 1, 1994

By Roger M. Nendick

"IntroductionThe stages of development for bringing a mill into production demand that a flowsheet for the process be developed at an early stage. Detailed engineering of the mill may then proceed without duplication of engineering effort on alternative processes. In the case of gold and silver mills, several process alternatives exist which must be evaluated before the flowsheet is finally fixed. The recently developed Carbon-in-Pulp process has added to this choice.Clearly, the major factor in determining the most suitable process is the amenability of the particular ore to a given treatment. Other factors that will also influence the choice are location, climate, power and water supplies, and available capital.Gold and silver milling processes can be divided into three main types:Gravity Concentration;Flotation;Cyanidation.Combinations of the three are frequently used; i.e. flotation followed by cyanidation of the concentrate, or gravity concentration in the grinding circuit with cyanidation of the classifier overflow. The following are the salient advantages and disadvantages of the three main alternatives.Gravity ConcentrationGravity concentration is suitable for free-milling gold ores, i.e. ores in which the gold is relatively coarse and free from sulphides. It should be noted that just because an ore is high grade, it is not necessarily free milling.Gravity concentration methods include jigs, shaking tables, spirals and more recently Reichert cone concentrators. All methods exploit the density difference between gold, which has a specific gravity greater than 15, depending on how it is alloyed, and the gangue, which usually has a specific gravity range of 2.7 to 3.5.A concentrate grade of several hundred ounces per ton might be produced, but recoveries by gravity alone are generally low in comparison to other methods. For this reason, gravity circuits are usually used in combination with flotation or cyanidation circuits."

Jan 1, 1983

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By Ronald C. Schimmel

In 2006, the Corus IJmuiden pellet plant produced approximately 4.6 mln tonnes of pellets. Corus IJmuiden is about to increase its pig iron production to 6.4 mln tonne HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50% high basicity sinter and 50% acid pellets, both produced in-house. To enable an increased iron production, the capacity of the pellet plant needs to be raised to 5.0 mln tonne per annum. The capacity is increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

May 1, 2007

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992