Search Documents

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

By K. E. Haque

"This paper is a brief overview of the role of oxygen in cyanide leaching of gold feeds (e.g. ore, concentrate). As the majority of gold occurs in the elemental state (Au °), its oxidation is of vital importance for dissolution in the cyanide lixiviant. The cyanidetion at high pH is favourable for the oxidation of Au° with a mild oxidant such as air or oxygen. Beside oxidation of gold, deleterious effects of soluble sulphides, arsenates, antimonates on cyanidation of gold can be alleviated by preaerating the leach slurry with air or oxygen (i.e. preaeration process).If gold is refractory due to its occlusion in sulphides, silicates, tellurides, etc. then gold liberation is possible by roasting in the presence of oxygen or by leaching under oxygen pressure. The data in the recent literature indicate that reactive oxygen supplied by H202, Na202, Ca02 or 03 during cyanidation can accelerate considerably gold oxidation-cyanidation and yield high gold recovery in much shorter leach time. The information compiled in this review leads to the conclusion that oxygen plays a vital role in the dissolution of gold in cyanide lixiviant."

Jan 1, 1992

By W. F. Moore

"In January 1981, Quintette Coal Limited (QCL) signed a 2a-year coking coal sales agreement with the Japanese Steel Industry which was followed by the commencement of mining operations in October 1982 and preparation plant operation in November 1983. During the mine 's startup, the town of Tumbler Ridge, the Anzac rail spur line, coal port facilities at Ridley Island plus numerous related elements of infrastructure were completed to support QCL and the neighbouring Bullmose operation in northeastern British Columbia. QCL's annual product coking coal levels have accelerated from 2.9 to 5.2 Mt between 1984 and 1986 with related increases in total mined volume from 14.8 to 41.0 M BCM between 1983 and 1986. This paper presents an overview of QCL 's current operation and related infrastructure. Development BackgroundDuring the 1970s, the Japanese Steel Industry (JSI) was forecasting a steady and significant growth in its steel production. By 1980 they were expecting crude steel production to increase from about 105 Mt in 1980 to 125 Mt by 1985 and almost 140 Mt by 1990.Discussions between Quintette Coal Limited (QCL) and the JSI for the development of the QCL project began in the 1970s and continued over a period of several years. During that time detailed and regular meetings took place, at which technical and commercial presentations were made to the JSI. The geology of the project area and the alternative mining methods and sequences were studied in detail. The new rail line which would connect the mine to tidewater was a critical factor and received particular attention. Alternate routes for the rail line from Tumbler Ridge to Prince George were the subject of much detailed study and discussions. The Anzac route was chosen in the best long-term interest of the northeast area development, after careful consideration and advice from the Japanese side.The new bulk coal terminal on Ridley Island at Prince Rupert was also a key factor and completed the development of an independent and new major coal field to supply the JSI. The QCL project and the development of the northeast area of British Columbia was a major strategical initiative of the JSI. It provided Japan with an important new coal field which was both self-sufficient and distinct from the traditional Japanese coal field resources in southern Canada, Australia, and the United States."

Jan 1, 1988

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world's nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By Doug Barnstable

"Quinsam Coal Ltd. is assessing the potential of developing a thermal coal deposit near Middle Quinsam Lake on Vancouver Island. The coal reserve outlined is classified as a high-volatile, bituminous ""A” steam coal and is composed off our separate seams of varying quality within the Late Cretaceous Comox Formation.Open-pit mining methods will utilize a walking dragline and a truck / shovel module as the primary stripping tools. Following washing and mechanical drying in a Baum jig preparation plant, the coal will be transported to the proposed dock at Campbell River for shipment via 55, OOO-DWT vessels to world markets. The paper will outline the development and status of the project to date. IntroductionQuinsam Coal Ltd. is a joint venture of Weld wood of Canada Ltd. and Luscar Ltd . The participants propose to develop a thermal coal mine in the Middle Quinsam Lake area, 17 miles inland from Campbell River on Vancouver Island (Fig. I). By acquiring all the assets of Canadian Collieries in 1962, Weldwood also came to own the coal rights of the area proposed for development. Luscar Ltd . ha s been designated as project manager until completion of construction and thereafter will act as operator of the mine.Surface mining methods will be used to produce approximately 1.0 million short tons of coal annually from the Quinsam property. Seven separate mining pit s will be developed along with the supporting minesite facilities, including a proper paration plant. Transportation routing to Campbell River and the establishment of docking facilities will be required. The initial economic life of the mine is 12 years, with the provision to extend this in the future by developing higher-ratio, auger or underground reserves."

Jan 1, 1980

By G. J. Reid, D. H. Stewart

"A diversity of structures and rock types in the Aft on pit has resulted in the occurrence of several different types of wall failure. Delivery of ore to the mill has not been affected and safety has not been compromised thanks to effective remedial 1V0rk and to a system of structural mapping, back analyses of failures, groundwater monitoring, and simple movement monitoring. Remedial measures have included artificial support, dewatering (including vacuum-assisted drainage), flattening of slopes and temporary buttressing. This paper describes six different wall failures at Afton and highlights the features of each. Examples given include rates of movement, extent and direction of movement, and piezometric responses. The practical, low-cost monitoring system was sufficient in one case to allow the prediction of date of failure. IntroductionThe Afton copper deposit is located 13 km west of Karnloops, British Columbia and has been mined for nine years out o f an expected eleven-year life. Open pit mining has reached 700 feet below sur face and is designed to proceed to 970 feet below surface by the time the pit is completed. The excavation is in a structurally and lithologically complex environment. Inevitably, some wall failures have occurred but these have been limited to small, manageable failures which have not compromised production or safety. To handle the failures it has been necessary to understand their nature. Of prim e concern has been the rate s of movement, but displacement vectors and hydrology have been monitored as well. The monitoring system is based on EDM surveys and on wire extensometers and plates set across cracks. Water levels have been read in standpipe piezometers. At Afton the emphasis has been on simple, practical, and inexpensive monitoring and because rock type s and structures play such a major role in any failure, detailed geologic al mapping is carried out."

Jan 1, 1988

By Gene O. Cowie

"Zinc, which once enjoyed an unchallenged position in the field of decorative applications, has lost a substantial share of its markets to other materials, particularly plastics. This turn of events has led the zinc industry to explore new market areas, particularly those applications where the engineering properties of zinc can be utilized. This paper gives an overview of the zinc industry&apos;s efforts to develop the data base and product development technology which have enabled zinc alloys to emerge as engineering materials. It also indicates those areas in which the research facilities of the zinc industry must be employed to ensure that zinc alloys keep pace with developments in competitive materials and processes.The Materials RevolutionThe development and utilization of new materials and manufacturing processes progressed for centuries by evolution. Recently it erupted into a revolution, which may become as significant as the industrial revolution. The materials revolution has impacted upon many industries, but none has been affected more traumatically than the North American automotive industry. The plight of that industry is of great importance to us because their problems have, to a great degree, become problems to the zinc industry.Much of the impetus behind the automotive trauma came from the battery of motor vehicle regulations promulgated by the United States government in the 1970s. These regulations required that the efficiency of passenger cars, in terms of miles per gallon, be approximately doubled in ten years. In view of the fact that major changes in the automotive world require three years of lead time to implement, the industry was left with only seven years to perform the task. The automotive industry was simultaneously required to make progress in other areas, such as reduced emissions, reduced cost of repairs and increased levels of occupant safety. These added demands not only diverted some of the available resources away from efficiency goals, they often ran in direct conflict. For example, when you are required to provide a front bumper which will absorb the energy of a 5-mile -per-hour barrier collision, you must add both hardware and structure to the vehicle. This adds weight, and increased weight reduces miles per gallon."

Jan 1, 1983

By R. L. Guerguerian, Eugene Bercel

"Grinding mill hydrostatic trunnion bearings require an external pumping source to provide and maintain the oil film between the bearing members. In order to guarantee a predetermined minimum film thickness, the lubrication system tends to be oversized. The oil film is ""indirectly"" controlled by flow, pressure and temperature monitors with fixed settings on the conservative side. This can lead to excessive maintenance and abbreviated life for the lubrication system components. A reliable method of monitoring actual film thickness would not only provide greater mill availability, but also minimize maintenance costs.This paper describes the instrumentation installed in Dominion hydrostatic bearings, and presents results of field tests where the output of that instrumentation was recorded under various operating conditions.IntroductionThe trend toward larger and more sophisticated grinding mills has made the operators of these machines increasingly vulnerable to financial loss, as the cost of downtime and repairs has increased directly with machine size. In order to guard against such losses, it is becoming imperative that large, sophisticated grinding mills be equipped with protective instrumentation to monitor some of the critical operating parameters and to identify events and trends which, if they go unnoticed, can lead to excessive maintenance costs and machine downtime. The idea of protective monitoring systems is not new. The operators of certain types of machinery where a high degree of safety is required or where machinery health can deteriorate very rapidly, as in the case of high-speed turbo-machinery, have long been using protective instrumentation on their machines. The increased awareness of the benefits of monitoring machinery conditions and the availability of reliable and relatively low-cost instrumentation of a large range of sophistication is making the practice now widespread. Traditionally, grinding mills have not been considered as high-risk machinery requiring instrumented protection. However, the trend, mentioned earlier, toward employing fewer, but larger capacity, mills increases the risk of significant disruption of production, and therefore measures to minimize the risks are desirable."

Jan 1, 1981

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

By Deni Pageau, Deni Caron

"This paper describes the operations of the open pit and emphasizes particular aspects of Les Mines Selbaie. The open pit as well as its related services were incorporated into a complex which includes an underground mine and a concentrator. The equipment was chosen with the objective of auto-sufficiency during each phase of mining. The paper outlines the organization and the methods used in each step of mining, notably: drilling, blasting, loading, transporting and crushing. The responsibilities of the Engineering Department are also outlined from the conception of the open pit to the latest follow-up methods. A short resume of the results which have been obtained as well as suggestions for improvement are provided.Layout in Consideration of Main SiteThe A-I zone deposit is located I km from 8 zone. Open pit mining of A-I zone required the regrouping of different services to those already existing.I. The crusher was placed in an area close to the concentrator in order to minimize the length of the conveyors and to provide space for the crushed ore reserves (50000 tonnes).2. The location of the service building (warehouses, mine offices, maintenance, engineering and geology) raised a few problems. Because of the multiple services provided therein , it was impossible to fulfill all the requirements, and the garage in itself is located a fair distance from the pit. Added to this inconvenience is the fact that heavy equipment regularly travels throughout the main yard.3. The storage of explosive magazines has been changed to obtain more surface space and meet government regulations.4. A space has been provided for minor repairs in the garage used during exploration. A trailer was installed next to the garage to provide a lunch room for the employees working at the open pit."

Jan 1, 1990

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world&apos;s known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982

By K. E. Haque

"Radium is selectively leachable from uranium ores with various types of lixiviants. Among a number of lixiviants tried on Midwest Lake uranium ore, KCl provided the highest per cent of radium extraction (60%-65%). Leach results further confirmed that a certain portion of Ra is not amenable to KCl leaching. More than 99% of the dissolved radium could be removed by treating the KCl leach liquor with barite or with radium selective complex resin (XFS-43230 resin of Dow Chemical Inc.) or by precipitating as RaBaSO4. Uranium leachings from the Ra-preleached uranium ores indicate that radium leaching prior to uranium may be applied as an extension to the conventional or alternative (i.e. acid chloride) leaching process of uranium ores in order to yield environmentally acceptable tailings (in terms of radium in the solids).IntroductionAt present, radium is considered as an environmental issue, particularly for uranium ore mine mill operations, rather than a commercial commodity. Radium was once a highly priced commodity ($180/mg during the first great war) but now it hardly has any commercial value. Its principal applications were in the field of cancer treatment and in the manufacturing of lwninous dials for watches. Nowadays readily-available synthetic radioisotopes are finding applications in place of radium.Because of scarcity and high toxicity, further commercial applications have never been explored.Radium was first discovered and extracted from uranium ore by P. Curie, M. Curie and G. Bement in 1898. Radium is widely distributed in nature but in exceedingly minute quantities. It is one of the daughter products of uranium or thorium and its maximum concentration is 3.3 x 10-7 part/part of U(21). Because of its short half-life (approximately 1620 years) in a geological time scale, its occurrence in nature as a distinct mineral is most unlikely.The details of the original radium leaching process developed by the Curies and Bernont are in the literature. This process essentially involved the roasting of uranium ore with caustic. carbonate followed by sulphuric acid leaching. The precipitated RaSO4 and BaS04 were treated with boiling Na2CO3 to convert them into the corresponding carbonates which later were dissolved in HCI. RaCI2 and Ba02 were separated and concentrated from the chloride liquor by fractional crystallization. But, in the course of time several modifications were made or proposed to the original process. Regardless of the process employed 226Ra extraction from the uranium ore was seldom better than 90%, and further as much as 20% 2URa loss took place during the concentration and purification process."

Jan 1, 1987

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By A. A. Burgoyne

"The McDame chrysotile asbestos deposit located near Cassiar in northern British Columbia isfound at depth and on trend to the southeast of the currently mined open-pit Cassiar asbestos deposit. The ultramafic rock hosting the McDame is serpentinized peridotite of the Upper Paleozoic Sylvester Group contained in an ophiolitic sequence preserved within a lower thrust sheet of the Sylvester Allochthon. The Sylvester stratigraphic package is a series of thrust slices composed of argillite, tuff and volcanic flows, diorite and serpentinite. Contacts between units are often fault-controlled.The McDame asbestos-bearing ultramafite is considered to represent a separate interleaved fault-bounded slice of rock distinct from the Cassiar asbestos deposit.Asbestos mineralization of the McDame deposit was discovered in /978. Exploration during /980 and /98/ focused on extensive underground drilling of the deposit and in /983 on geological mapping, airborne and ground magnetic surveys. In /984 a 622.5 m borehole was drilled with a 242 m intersection of McDame ultramafite of which the lower 15/ metres contain potentially economic chrysotile asbestos. The McDame deposit averages 90 m thick, trends north-south, dips easterly and plunges southeasterly. The deposit is estimated to contain geological reserves in the order of 62 million tonnes containing asbestos fibre similar in value to the Cassiar deposit.The McDame is considered a major world-class asbestos deposit. A decision to develop and mine the deposit will require further substantial underground exploration and evaluation. A + 1200 m exploration adit driven to the hanging wall of the deposit was undertaken in 1985 in anticipation of bulk sampling and diamond drilling in 1986."

Jan 1, 1986