Search Documents

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By Troy Boisjoli

Since its discovery in February 2014, the Arrow Uranium Deposit has undergone rapid development through aggressive and systematic drilling programs and is now being progressed through advanced engineering and permitting. Based on the 2018 NI 43-101 Technical Report, the Probable Mineral Reserve estimate totals 234.1 million (“M”) pounds (“lbs”) triuranium octoxide (“U3O8”), contained in 3.43 M tonnes at an average grade of 3.09% U3O8. The proposed processing plant at the Rook I Project (the “Project”) will be capable of producing up to 31 M lbs of U3O8 per year, with a projected mine life of nine years based on the Probable Mineral Reserve estimate, although NexGen is permitting a 24-year operating life at the Project assuming the majority of Inferred Mineral Resources are upgraded to Indicated Mineral Resources with continued mineral resource development drilling. The Project will be developed through transverse and longitudinal longhole mining methods, pairing primary and secondary stoping techniques with a high degree of equipment mechanization which will provide a combination of good productivity, high extraction, and stable back support. This next generation of uranium operations combines the use of advanced tele-remote equipment and instrumentation with a low-cost bulk mining method and a best-in-class tailings management practice, effectively reducing operating costs and setting a new standard for elite environmental and social practices.

Jan 1, 2020

"In flotation research, relatively little attention has been paid to understanding particle-bubble detachment phenomena compared with attachment processes. With CFD models now incorporating attachment/detachment kinetics, it is important to obtain more accurate formulations for detachment probability. The formula most often used is due to Bloom and Heindel (2002) who proposed that the rate of detachment would equal the product of detachment frequency, as previously estimated by other authors, and probability of destabilization, as estimated previously by Schulze. These two factors both account for the balance between stabilization and destabilization forces, so the product accounts for this effect twice. An integrated procedure has been followed to estimate the overall detachment rate by re-analysing the process. In this analysis, detachment rate is calculated as the frequency of eddy-aggregate interactions (or “collisions”) sufficiently energetic to cause detachment. The Bond number analysis of Schulze has been incorporated into the turbulence frequency analysis of previous authors in an integrated way. The new formulation has essentially the same type of dependencies as the previous model, but gives a lower detachment frequency. Detachment frequency has been calculated using the new formula for conditions relevant to an industrial flotation cell. INTRODUCTIONIt is well known that the effectiveness of froth flotation for separating different minerals is limited to the particle size range of approximately 10–100 mm (Trahar & Warren, 1976; Trahar, 1981). Fine particles tend to follow fluid streamlines around bubbles limiting the likelihood of bubble–particle collision, while coarse particles can be more easily detached from bubbles before collection can be achieved.Phenomenological models have been developed to quantify the physico-chemical aspects of flotation in order to better understand factors affecting these limitations, and to suggest ways of broadening the window of feasible flotation. Koh and Schwarz (2008) have incorporated these models into computational fluid dynamics (CFD) models of flotation cells, which have then been used for design and scale-up purposes (Schwarz et al., 2015). The models are based on dividing the process of bubble–particle interaction into three subprocesses: collision, adhesion and detachment. Of these, the hydrodynamics of bubble–particle collision and the probability of adhesion have been studied most extensively, while the dynamics of detachment have received relatively little attention from investigators."

Jan 1, 2016

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By Y. Kusuda

Since 1981, the Annaka refinery has recovered zinc from zinc leach residues by the Waelz Process. The important considerations of this process are the prevention of the growth of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate. In this paper, simulation predictions and the results of the industrial operation regarding the prevention of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate at the Annaka refinery are reported and compared.

Jan 1, 2006

By F. W. Wellmer

"This paper discusses the changing nature of reserve/consumption ratios, using data from Canadian operations and focussing particularly on copper.IntroductionStudies in world metal consumption and world metal reserves are done regularly by the U.S. Bureau of Mines, the German Federal Institute of Geosciences and Raw Materials, and other institutions. Formerly, on the basis of these data, the following figures were calculated:• a static lifetime of reserves-reserves at year end divided by the consumption of the previous year;• a semidynamic lifetime of reserves-reserves at year assumed constant growth rate.These figures were severely criticized because they were purely theoretical and did not consider the availability of the raw materials.Recent practice is to calculate reserve/consumption ratios (R/C ratios) for periods(1) or for different years(2,3) and to interpret the trend. For base metals, these R/C ratios are increasing (Table 1). This had led to the conclusion that today the relative availability of base metal reserves has increased as compared to 10 or 15 years ago(4,5) As there are normally numerous deposits for each commodity, the anticipated production rates of deposits are irrelevant to this conclusion as long as the statistical distribution of possible production rates does not change significantly.The above conclusion is only justified if the quality and the nature of the data base remain the same. This is certainly the case for the consumption data. It is also assumed for the quality of the reserve figures, which usually take into account only proven and probable reserves. For the nature of the reserve figures, however, this does not seem to be true.Undoubtedly, the reserves increased in absolute terms between 1966 and 1978. To put the absolute reserve figures into perspective, it is common, as said above, to compare them with the mine production, which increased in the free world between 1966 and 1978; e.g. for copper by 40%, for Pb by 17% and for zinc by 36%. However, the reserves are also influenced by other factors, such as average size of the mines, changes in the grade of the mined ore, price-to-cost relationships and the like.The purpose of this paper is to examine the nature of the reserve figures in more detail. Because the completeness of mining data published in Canada is rather exceptional, Canadian .data serve as an example and it is assumed that the conclusions can be extrapolated to other mining countries or at least to those with free market systems."

Jan 1, 1981

By L. Nastac, Y. Xuan

"The metal-matrix-nano-composite (MMNCs) in this research work consists of an A356 alloy matrix reinforced with 1.0 wt. % SiC 50 nm diameter nanoparticles that can be dispersed within the molten alloy matrix via ultrasonic stirring technology (UST) and induction melting and stirring processing. The necessary ultrasonic parameters to achieve the essential cavitation for adequate degassing and refining of the A356 alloy as well as the optimum fluid flow characteristics for uniform dispersion of the nanoparticles into the A356 alloy matrix have been investigated in this study by using computational fluid dynamics (CFD) modeling with a magneto-hydro-dynamics (MHD) model and an UST cavitation model.The MHD model accounts for turbulent fluid flow, heat transfer and solidification, electromagnetic field as well as the complex interactions between the solidifying alloy and nanoparticles by using ANSYS Maxwell and ANSYS Fluent Dense Discrete Phase Model (DDPM) and a particle engulfment and pushing (PEP) model.INTRODUCTIONAluminum matrix nanocomposites can offer outstanding properties, including low density, high specific strength, high specific stiffness, excellent wear resistance and controllable expansion coefficient, which make them attractive for numerous applications in aerospace, automobile, and military industries field (Bozic, 2010, De Cicco, 2009, Elshalakany, 2014, Goh, 2006, Jia, 2013 and 2015, Liu, 2014, Reihani, 2006, and Su, 2010).As shown in literatures (Aki, 1999 and Mussert, 2002), it is highly advantageous to use nano-sized ceramic particles to produce metal matrix nano-composites (MMNCs) since similar ductility and higher strength with the metal matrix can be achieved. Currently, there are several fabrication methods of MMNCs, including mechanical alloying with high energy milling (Chen, 1997) , ball milling (Filho, 2003), nano-sintering (Groza, 1999), spray deposition, electrical plating, sol-gel synthesis, laser deposition, etc. The mixing of nano-sized ceramic particles is normally lengthy, expensive, and energy consuming.Ultrasonic Stirring Technology (UST) has been extensively used in purifying, degassing, and refinement of metallic melt (Jian, 2005, Khalifa, 2008, Eskin, 2002, Xu, 2004, and Meek, 2006) mainly because introducing the ultrasonic energy into a liquid will induce nonlinear effects such as cavitation and acoustic streaming. SiC nanoparticles are widely used as reinforcement particles due to their relatively good thermal and chemical stability. Ultrasonic vibration can improve the wettability between the reinforced nanoparticles and the metal matrix (Lan, 2004, Cao, 2008, and Yan, 2011), which will assist to distribute the nanoparticles more uniformly into the metal matrix. Ultrasonic cavitation in liquids causes high speed liquid jets of up to 1000 km/h. Such jets press liquid at high pressure between the particles and separate them from each other (Hielscher, 2005)."

Jan 1, 2016

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By Owen Owens, W. P. Armstrong

Abstract- The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993