Search Documents

By V. Fiedler, H. Lachmund, R. Bruckhaus

"After producing some 50 million tonnes of crude steel the two BOF vessels at Dillinger Hüitte steel plant had to be replaced in 2000/01 due to large deformations. The new vessel design was optimised after a number of theoretical evaluations.Refractory investigations were carried out as well as temperature measurements of the shell to provide a basis for selecting a suitable steel grade. This was found in a DH-GTS development - P420M HT - with high strength at elevated temperatures and excellent weldability and made it also possible to build the vessel without any cooling system.After putting the first vessel into operation the metallurgical results showed no remarkable improvement compared to the old vessel, and were therefore not satisfying. With the help of cold model investigations the arrangement of the tuyeres was modified to improve the flow conditions and the interactions between oxygen jet and the heterogeneous plume of the bottom stirring gas. Further optimisations were obtained by a variation of lance tips and a newly developed lime addition model."

Jan 1, 2004

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By Luis Bergh, Juan Olivares, Juan Durán, Juan Yianatos

"In the last decades heuristic approaches based on logic rules have been one favored tool to control flotation units and plants on top of distributed control systems. Fundamental knowledge on flotation processes, expressed in reliable models, and programs to assure the quality of the information, contained in available measurements, are still insufficient to develop robust predictive control strategies. In this paper the idea of using simplified models, when a known disturbance is coming into the process, is explored. As a first approach, the set points of the froth depth and air flow rate controllers are estimated based on this model. Since these target predictions are only approximate, a conventional feedback expert system, based on logic rules, continues the task of calculating the set points of the distributed controllers, in order to decrease the gap between actual and desirable metallurgical targets. This combined actions permitted a fast response of the process to change the operation of the circuit when a measured disturbance is detected. This control system was implemented and experimentally evaluated in a pilot rougher flotation circuit, with three pneumatic cells, with froth depth and air flow rate controllers in each cell. Since the circuit is operated for the air-water system, a phenomenological model, with parameters estimated from industrial data, is fed on-line with real operating variables and virtual values, characterizing the feed (grades, solids%, particle size distribution), in order to predict the metallurgical targets (recovery and concentrate grade). Several cases are discussed showing the benefits of this control system and the possible improvements to work on. INTRODUCTIONToday, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design."

Jan 1, 2016

By R. Krentz, P. D. Cordingley

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Major changes to the refining process were required when the Moa sulphide feed, with its unusually high cobalt content, was introduced in the early 1990&apos;s. In the period 1994 to 2005 the production capacity of the refinery has increased dramatically to match increases at Moa, and significant process improvements incorporated. The process flowsheet consists of the original ammonia leach process, optimized for cobalt chemistry and overall leaching capacity. Extraction of metal values is followed by the unique nickel-cobalt separation technology, in which most of the cobalt is separated from the ammoniacal nickel sulphate leach solution by precipitation as a nickel-cobalt hexammine salt. This salt is refined from a Co:Ni ratio of 1:1 to over 10,000:1 by selectively leaching nickel, redissolution and recrystallization in ammonium sulphate solution. Nickel and cobalt are recovered using the well-known Sherritt hydrogen reduction technology. This paper reviews the chemistry described above, examines some of the changes in operating conditions made over the years and highlights some of the recent physical changes made to the refinery.

Jan 1, 2005

By A. M. Brown, P. V. Straznicky

Dimpling as a means of flush countersinking rivets is an old process predominantly used in secondary structures. The introduction of GLARE as an aerospace material has renewed interest in dimpling and its possible application in primary structures. The dimpling process is able to prevent the creation of a machined knife-edge in the thin aluminum plies of the GLARE sheets. In addition, dimpling eliminates the need to use reduced height rivets, such as the NAS 1097 rivet style. This investigation expands on an earlier study into dimpling of GLARE by Rans and Straznicky. In order to tailor the dimpling process to GLARE, FEM simulations were developed. After verification, a study was performed to find the best parameters for dimpling GLARE3-2/l. Coupon fatigue tests were carried out and the dimpled joints demonstrated increased fatigue lives over the conventional machine countersunk joints. Future wide panel fatigue tests are planned to confirm the usefulness of dimpling thin GLARE laminates.

Jan 1, 2006

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man&apos;s varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930&apos;s when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years&apos; duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry&apos;s basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada&apos;s historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country&apos;s major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

By J. S. DeLury

Introduction The problems of metallogenesis are largely related to those concerning the origin of igneous rocks, which, in turn, are involved with the question of crustal mechanics. Many ore-bodies are genetically related to associated intrusive and there is an equally close association apparent between igneous intrusion and crustal deformation. The problem of ore-deposition is concerned, therefore, with the fundamental problems of geology. For a long time speculations regarding crustal movements rested largely on the contraction theory and its associated conceptions. Vertical movements were considered to be all important and horizontal movements secondary to them. Magmas were pictured as rising more or less vertically in the crust and were believed to form in vertically disposed magma-chambers or reservoirs. The principle of magmatic differentiation seemed to offer the best explanation of the origin and association of diverse rock types and it seemed also to require the existence of quiescent magma-chambers for the admittedly slow process of differentiation. Accumulating evidence of the importance of horizontal movement in the crust, has, along with other considerations, discredited the contraction hypothesis and many of the inferences that go with it. The same evidence may require some change in the prevailing conception of the origin of the various types of igneous rock and of the mechanics of intrusion. Geologists are now at sea concerning some of the vital and fundamental problems of the crust, and the field is open for speculation. The writer is developing a hypothesis which seems to permit an explanation and? a correlation of earth structures and phenomena. If it rests on a firm foundation, the hypothesis, because it is fundamental, is certain to have a profound bearing on the problems of economic geology. It is for this reason that an outline of the hypothesis is offered at this time. Only a few of its economic bearings are foreseen at this time and these will be indicated.

Jan 1, 1932

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968

By Mohammad. M. Khajeh

Rock mechanical properties are important parameters in geomechanical simulation. Considering stochastic heterogeneous models rather than conventional homogeneous layer cake models leads to more realistic simulation results and uncertainty assessment. These heterogeneous models are usually fine scale models generated by geostatistical techniques. Although considering high resolution property models is desirable, geomechanical simulation with a fine scale model is not computationally feasible for full?field, coupled geomechanical-flow simulation. Upscaling of property models is necessary to move from fine scale/high resolution property models to coarser scale/low resolution models appropriate for simulation. Local numerical upscaling was proposed by Khajeh et al. (2012) to describe the macroscopic elastic behavior of complex heterogeneous media and is expanded upon in this work. This numerical technique is not restricted to specific geologies as typical analytical techniques are. Moreover, transversely isotropic deformation is considered rather than the usual assumption of isotropic deformation. To compare the accuracy of the upscaling methodology, in this study shear strain is considered as the geomechanical response of a synthetic facies model and the response of the coarse scale model is compared to other conventional analytical averaging techniques. It is found that the numerical upscaling technique better approximates the geomechanical response of the fine scale model.

Jun 1, 2012