Search Documents

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By T. S. Smith, C. C. Rennie

"THE LEAD-ZINC and tungsten mines of Canadian Exploration Ltd are on Iron Mountain, 8 miles south of Salmo, B.C., in the Nelson mining division. Relative location of the mines is shown on the general plan.First recorded lead production was in 1908 from surface outcrops. Small amounts of high lead ore were mined intermittently until 1926. No major lead-zinc production occurred until 1949 when outcroppings on the south side of the mountain were mined and diamond drilling began to prove the existence of a large replacement orebody. Lead-zinc ore has been mined continuously from the Jersey orebodies since March 1949, with monthly tonnage as high as 50,000 tons per month, but currently averaging 30,000 tons per month.Schee1ite-bearing tungsten ore was found in 1942 by H. Lakes in an old adit and open cuts at the north end of the Emerald tungsten orebody. The Emerald tungsten mine was developed by the Federal Government as a Wartime Metals project and operated for eight weeks in the fall of 1943, when the poor demand for tungsten closed the mine. Canadian Exploration Ltd. purchased the mine in 1947 and mined in excess of 100,000 tons in 1947-48 until the demand for tungsten dropped again and interest was centred on lead-zinc. The Federal Government repurchased and reopened the Emerald Mine in 195 L and built a new concentrator. The mine and mill were sold back to Canadian Exploration Ltd. in 1952.Regional Geology and IntrusivesThe host rock for both the lead-zinc and tungsten mineralization is the Laib formation of Lower Cambrian age, which consists of 400 feet of crystalline limestone underlain by beds of argillite, and argillaceous limestone locally altered to ""skarn"" or ""tactite"". The Laib limestone is overlain by black argillite and underlain by the Reno quartzite of Pre- cambrian age. Repetition of folded beds has allowed the interpretation of the large isoclinal fold which repeats the limestone (see general cross-section). Dolomitization and the associated lead-zinc ore have been found only in the right-side-up limestone and are not known in the overturned limestone.Two elongated stocks of granite cut the sediments. The Emerald stock outcrops along the east side of the Emerald tungsten mine and again west of the Jersey workings, while the Dodger stock outcrops only at the north end of the Iron Mountain. The shape and attitude of these bodies are believed to have been governed partly by pre-granite faulting and partly by pre-granite folding of the sediments. Although some forceful intrusion may have occurred the detailed granite surface indicates a gentle stoping emplacement."

Jan 1, 1949

By R. G. Bradbury

The paper uses two hypothetical, but typical, situations to show that hydraulic rock drilling equipment has very significant economic advantages over pneumatic equipment both in drifting applications (even in the situation where advantage is not taken of the high productive capacity of the hydraulic drill) and production drilling applications. Other factors, including the non-economic advantages and the disadvantages of hydraulic drilling, are discussed. The paper concludes with a brief analysis of why the Canadian mining industry has been slow to take advantage of this apparent broadly advantageous advance in rock drilling technology.

Jan 1, 1979

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By D. E. Macdonald

"Approximately 2.0 million tonnes of phosphate rock is imported from the U.S. to Alberta annually and is used in the production of agricultural fertilizers. No phosphate rock is presently mined in Canada, although sources of igneous phosphate have been mined in the past. Sedimentary phosphate rock is found in nine geological units within the Cordilleran Foothills and Front Ranges region of Alberta. The Devonian-Mississippian Exshaw Formation, Permo-Pennsylvanian Rocky Mountain Supergroup, and the Jurassic Fernie Formation have the best potential f or future development. Most of the phosphate rock in Alberta is of low grade and lies within restricted land use areas. The best over-all resource potential lies in the Fernie basin area of southeastern British Columbia, in the Fernie Formation. The possibility of deep phosphate rock deposits in the plains region should be examined.Phosphate rock is mined in Idaho, Utah, Montana and Florida, and is shipped to Canadian fertilizer plants for processing. Raw phosphate rock is acidified, usually with sulphuric acid, by a wet process. Varying amounts of ammonia are added, and the fertilizer is pelletized. Future research, in western Canada, is needed in the beneficiating of low-grade ores and in the area of in situ mining. At the present time, phosphate rock sells for around US$50Itonne, and Alberta fertilizer companies probably pay in the range of C$7D-$85Itonne for U.S. phosphate rock delivered to the plant. Environmental concerns about phosphate rock processing are centred around gypsum tailing ponds, and radioactive wastes.U.S. supplies of phosphate rock are secure until the year 2000; however, by this time, the richer deposits in the U.S. may be exhausted. Alternate deposits, such as the ones in Alberta and British Columbia, might then be considered. Phosphate byproducts, such as uranium, vanadium, fluorine and rare earth elements, may help in making the processing of low-grade Canadian phosphates economically feasible."

Jan 1, 1988

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

By S. Kashani Nejad, M. Bellino, K. Collins, C. Tovee, J. Godwin

Motivated by safety considerations, logistical issues, transportation cost savings, product diversification, and marketing preferences, several uranium producers are revisiting their business models and supply chain configuration and, instead of selling dried yellowcake to downstream refineries, they are moving to build in-house calcining facilities. Drying and calcining plants are relatively low-cost facilities to build and operate. The execution period of a typical yellowcake drying and calcining project is also relatively short and alternative construction methodologies, such as modularized solutions, are available. The drying and calcining technologies used for yellowcake are relatively mature, environmentally contained, and well supported by qualified vendors. The drying and calcining circuits also seamlessly integrate with upstream and downstream operations. These either produce a dried yellowcake or calcined U3O8 which are notably safer and easier to transport and market. This paper presents an overview of the recommended technology and project development considerations for yellowcake drying and calcining facilities.

Jan 1, 2020

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By Thomas. Lisa, Mark Coleman

Schenck Process is an established customer-driven solutions provider, utilising its knowledge, expertise and technologies to transform production processes. Operating across several industries Schenck Process have developed quality solutions from their range of equipment to solve problems and fill holes in other people’s processes. In the non-ferrous metals industries Schenck Process have been using their Clyde Brand solutions in Pneumatic Transport to solve problems on smelter sites for a number of years, handling of concentrates, additives and metallurgical dusts. Working alongside clients around the world they have developed a number of dust handling systems for flash furnaces from New Boliden, through Codelco to PASAR. Solving handling issues in dust collection has proved to suit Schenck Process range of equipment well and now a series of solutions are available. Solutions have been developed to handle materials up to 600°C and can convey over 1 km. Conveying to remote location for disposal, injecting directly into a furnace through lances, return to furnace burner feed, or deliver and dose into leaching reactors, Schenck Process are ready to ‘make processes work’. Historic solutions at New Boliden and Codelco demonstrate a range of material application and the long term performance of the equipment. Recent installations at Pasar utilise the Schenck new ProPhaseTM equipment and handle the Waste Heat Boiler and ESP dusts directly and simplify the dust train. The paper will seek to show how this equipment can bring benefit in handling high temperature materials directly and eliminate several traditional steps that are often unreliable. The systems can be paired with Schenck Process new PHASiQTM and STREAMiQTM control systems which are complete PC, HMI, PLC, Interface system with full SCADA, Data Storage and IoT ready remote interrogation and support available. Installed in this challenging environment the systems are ready for smelter use. The systems can be also joined to our new E-nizingTM web portal. A perfect partnership to deliver the trend in ‘Big Data’ while providing visibility and off site support. The paper will show how these systems can deliver reliable equipment and remote support for these often isolated sites as well as delivering rapid return on investment. This paper discusses a step change in simplifying Flash Furnace Dust handling which Schenck believes shows the truth of Schenck Process Solutions claim that ‘we make processes work’.

Jan 1, 2019

This growing dependence of Canada upon foreign mineral commodities, just referred to, applies particularly in the direction of the United States. There is, in fact, no more significant feature of Canada's mineral trade than the manner in which it affects the Dominion's commercial standing with that country. Our heavy adverse balance of trade with the United States is perhaps not a matter of such wide concern or frequent comment as was the case two or three years ago. It is, of course, a well-known fact that the Dominion each year buys from the States a volume of goods to a value enormously in excess of our sales to that country. And it has come to be accepted as a ?normal, though not altogether satisfactory, feature of our international commerce that a huge portion of the bill incurred by our American purchases must be met, not by our American sales, but by the proceeds of our sales to other countries, not-ably Great Britain. It is a three-cornered situation in which our trading deficit with the United States is covered largely by our trading surplus with the United Kingdom. In this situation the mineral trade plays a remarkable part. If one delves into the details of our transactions with the United States it will be found that, in one sense, the mineral trade is entirely responsible for the huge annual balance against the Dominion. In fact, Canada gets decidedly better than an even break on Canadian American trade, if one leaves out of account the three mineral groups, "iron and steel", "non- metallic minerals", and "non-ferrous metals".

Jan 1, 1924

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

By A. Ghahreman, M. Oliazadeh

"Heap leaching is an attractive process for low grade deposits where the metal content of ore does not justify the high cost of milling and agitated leaching. In general, the heap leaching capital cost is low, construction is rapid, and production costs are low. The primary disadvantage of heap leaching is low recoveries (typically 65% of agitated leach recovery); thus, recovery improvements could convert more lower-grade deposits into minable reserves. This will also allow to process primary sulfide ores and result in a dramatic expansion of the technology, as ~80% of total ore types are sulfidic in nature. The old gold operations tailings are another massive source of low-grade gold material that can be retreated by the heap leach process. The major parameters affecting the recovery rates are ore characteristics (mineralogy, particles size of metal and host minerals, ore permeability), and operational conditions (segregation of ore, compaction, leach cycle time, lift height, and solution application rates). The design of a percolation leach process is based on a limited number of coarse ore bottle roll and/or column tests under ideal conditions. The economics of the projects and engineering design of the process facilities are developed based on the bench scale test work results and the application of the conventional engineering scale up factors. This paper will deal with the parameters affecting the HL efficiencies and focus on the potential improvement of gold heap leach recoveries. This would include design of heap leach operation and evaluation of processes such as fine crushing and bioleaching.INTRODUCTION Gold heap leaching is a hydrometallurgical process designed to treat amenable low-grade gold ores that contain typically 0.5 to 1.5 g/t gold (Marsden and House, 2006; Wong Wai Leong and Mujumdar, 2010). Ore is stacked by various types of equipment on an impermeable barrier, and a sodium cyanide solution is applied to the surface of the stacked ore. Gold, silver, and other metals contained in the ore are dissolved to various degrees by the cyanide application, as it percolates downward through the stack of the ore. The pregnant leach solution (PLS) is then collected at the bottom of the heap. The PLS is then sent to the gold recovery plant where the metals are extracted. The barren leach solution (BLS) is then reapplied to the top of the pad. Ore is placed on a pad or previously leached lift by various means, including ramp conveyor belts, radial-arm and self-leveling stackers, and trucks. Once trucks are used to construct the pads, the pad can be compacted and hence the pad should be graded and ripped or scarified (roughened up) with wheeled or tracked equipment to produce shallow cuts to increase surface area exposure to the leachate."

Jan 1, 2019

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By S. Homulos

"Introductory and GeneralTHE Northwest Territories comprise all that region -of Canada lying between Yukon Territory and Hudson bay and north of the 60th parallel of latitude. For purposes of mine .administration the Territories are divided into three districts: Yellowknife, McKenzie, and Arctic and Hudson Bay. Mining recording offices for the respective districts are maintained at Yellowknife, Fort Smith, and Ottawa. The mine inspection for the entire area, and also for Yukon Territory, comes under the Federal Department of Resources and Development. Two mining inspectors are responsible for these inspections: the Chief Inspector of Mines, with headquarters in Ottawa, who makes trips into the north at least twice a year, and a Resident Inspector, stationed in Yellowknife.The Resident Inspector is constantly making inspections of active properties. This involves a considerable amount of air travel as the region is large and properties are widely scattered.Although there has been prospecting and staking of claims in each of the three districts of the Northwest Territories, actual mining has been conducted only in the Yellowknife district, and for purposes of this paper we are solely concerned with that district."

Jan 1, 1952

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By J. C. Taylor, J. A. Davis

"Existing environmental, health and safety regulations have forced pyrometallurgical facilities worldwide to drastically change some of their traditional methods of operation. In extreme cases, a number of facilities have been closed due to their inability to conform to these existing regulations. Tougher future legislation and government policy will lead to more stringent regulations and enforcement policies. The efficient control of smelter secondary emissions will, therefore, become critical to successful smelter operation.Much attention has been paid to the smelter primary process off-gas systems, including the development of new process designs to reduce the number of uncontrolled transfer operations. However, even the most modem smelter design requires control of its secondary contaminant sources, which mayor may not be directly related to the process operation.This paper discusses some of the potential secondary emissions encountered in many of the present process technologies. A few of the emission sources presented are only periodic in nature, such as those caused by maintenance procedures, but which have the capability of forcing smelter shut-down because of their direct impact on worker health and safety. The paper deals with a variety of topics relating to the efficient control, maintenance and monitoring of secondary emissions in copper, nickel, aluminum, magnesium and lead smelters, as well as in iron foundries and steel making facilities. Examples of the typical problems encountered in each of the above process operations are presented, including fume control at furnace tapping and slagging locations, metal transfer stations, tapping launders, and ladle transfer operations. The parameters for the most efficient design of fume capture systems, problems encountered with the handling and clean-up of certain collected emissions, and examples of successful solutions in particular operations are discussed."

Jan 1, 1994