Search Documents

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By A. A. Brant

"Improving geological and geophysical evaluation should serve to reduce the early-stage risk assessment and there-by contribute to exploration expenditure stimulation. The limitations of present-day methods are reviewed, particularly as to anomaly causes, depth penetration and quantitative physical interpretative abilities. Some of the problems now under study are discussed. Future developments expected include the treatment of quantitized geologic and geophysical data, as well as continuing attempts toward computerized interpretation."

Jan 1, 1967

"SART technology is a useful tool for improving the economics of gold recovery from certain types of complex gold ores. SART liberates cyanide consumed by base metals such as copper, zinc and nickel, and enables the newly freed cyanide to be recycled to precious metals leaching while producing high-grade base metal sulphide concentrates for sale. The benefits of SART include the reduction in cyanide consumption, avoidance of cyanide destruction costs, minimization of risks of environmental non-compliance due to residues of cyanide destruction reporting to mine effluents, and generation of extra revenue from the sale of base metal concentrates. Concerns with SART typically include uncertainties around capital and operating costs and proper integration of SART into the overall metallurgical flowsheet. This paper presents two case studies addressing these concerns. The first involves actual costs of the full scale SART integrated into a gold heap leach operation and treating up to 500 m3/hr of leach solution at a mine in Mexico. The second involves field pilot testing and a preliminary cost estimate for integrating SART into a silver mine in Peru using Merrill Crowe.INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes in traditional gold extraction metallurgical flowsheets. One of the tools available to the industry to help deal with interferences of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle. Although SART is a commercially available technology, it is still relatively new to the industry. Fewer than ten (10) full scale plants have been constructed in the past couple of decades. Some of these SART plants are small, most are located at remote sites, and the majority have not operated on a continuous basis. This has resulted in a general lack of information in the industry about the true costs, operability and metallurgical performance of SART. BQE Water has been involved in the design, construction, commissioning and operation of large scale SART plants in Mexico, Turkey and Chile and has conducted field testing programs as part of the technical assessment of SART integration into various metallurgical circuits. Having built and operated numerous plants utilizing selective sulphide precipitation of heavy metals, BQE Water has gained unique insight into the design and control of the sulphidization stage of SART to minimize costs and ensure high efficiency in cyanide recovery."

Jan 1, 2017

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By B. Dyck, L. Verhelst

"Colloidal silica in Key Lake’s Solvent Extraction (SX) feed solutions has presented an operational problem for the mill throughout its history. The colloidal silica stabilizes aqueous continuous emulsions, resulting in elevated solvent losses and operational downtime. Through the years, many attempts have been made to solve this problem, but no viable solutions were found. By revisiting an idea dating back to the 1979 feasibility study and re-evaluating it under current operating conditions, a practical solution was achieved. This paper discusses Key Lake’s history around colloidal silica removal, starting with coagulation using a polyethylene oxide polymer (PEO), and ending with coagulation using a polyethylene glycol (PEG) polymer. The results of a mill trial using POLYSIL® RM1250 introduced at doses up to 300 ppm into the counter current decantation (CCD) circuit to clarify SX feed solutions are discussed with a focus on the benefits to SX.INTRODUCTION Colloidal silica has historically been a significant operational problem in the Key Lake mill. Silica originates from clays in the ore as well as concrete backfill intermixed with the ore resulting from the mining method used at Key Lake’s ore source, the McArthur River mine. The silica is dissolved as silicic acid into solution in the mill’s sulphuric acid leaching circuit. Once in solution, silicic acid polymerizes (Hearn, Smethurst, & Boskovic, 2016) forming a fine suspension of stable colloidal particles. These silica colloids are unaffected by flocculants and sand filtration reporting to the pregnant leach solution (PLS) as a fine turbidity in solution. Silica concentrations typically ranged from 700 to 1200 mg/L Si in the PLS fed to SX. Throughout Key Lake’s history, silica interactions in the Solvent Extraction (SX) process have made SX a mill bottleneck and a source of significant reagent costs."

Jan 1, 2018

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By A. L. McAllister

"MASSIVE sulphide deposits are found in two areas of New Brunswick, the St. Stephen area and the Bathurst-Newcastle area. In both, the geology in the immediate vicinity of the sulphide bodies is largely inferred from drilling results as outcrop is not plentiful and is, in fact, almost lacking in most places. With few exceptions these deposits have not been explored by underground methods. Consequently much of the. detail on the geology will only become known over a period of years as economic conditions make mining feasible.Much of the information contained in this paper has been supplied directly by company geologists. As a result of the number of contributors, some confusion of nomenclature bas to be anticipated. Cross-sections and plans of the individual deposits are, in most cases, as supplied by the companies concerned. Most of the interpretations are the responsibility of the author."

Jan 1, 1960

By J. C. O'Rourke

"This paper presents an overview of Alberta Oil Sands Technology Research Authority's in situ oil sands recovery project at its underground test facility near Fort McMurray. It covers the rationale for horizontal wells drilled from tunnels below the oil sands, the tunnel layout, the drilling program, and the recovery process and facilities. INTRODUCTIONThe Alberta Oil Sands Technology and Research Authority (AOSTRA) has constructed an Underground Test Facility (UTF) in the Athabasca oil sands deposit in northern Alberta, approximately 50 km northwest of Fort McMurray (Fig. 1). The facility initially is to serve as an underground laboratory from which to field test new approaches to in situ recovery of the bitumen (oil) in the Athabasca deposit.The UTF employs mine access to get at the effective exploitation of an oil reservoir. It does so, however, under conditions considerably more difficult than those faced by most other applications of the technology. Because of the unconsolidated nature of the McMurray formation, the development of drilling chambers directly in the reservoir would be prohibitively expensive. Further, mobilization of the extremely viscous bitumen requires intensive steam stimulation with the attendant concerns of large, complex well completions and potentially hazardous operations Over-all, the oil sands presents mining, drilling and operations challenges which push the technology to a new state-of-the-art. The UTF as it now exists consists of:• a 20 000 ha lease with all-weather road access;• 925 m of 5 m by 4 m tunnels in the limestone 15 m below the oil sands at roof depth of 178 m below the surface (Fig. 2);• two 3 m diameter steel lined shafts to a depth of 213 m;• administration and sur face mine support facilities from which to operate the UTF (Figs. 3 and 4);• underground piping systems to transport drill fluids, steam, produced fluids and services to and from the future well heads underground (Fig. 5);• surface steam generation and production handling facilities (Figs . 3 and 4).• a drilling rig and auxiliary systems specifically designed to drill long horizontal wells into the oil sands from tunnels in the underlying limestone (Fig. 6);• an experienced staff to engineer and operate the facility (Fig. 7)"

Jan 1, 1989

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. The Ore and ProductsThe mines in the Saskatoon area — Agrium, PCS-Cory, PCS-Allan, PCS-Patience Lake, PCS-Lanigan and IMC-Colonsay — extract the ore from the Patience Lake member. The mines in the southeast corner of Saskatchewan — IMC-K1 and K2, PCSRocanville — extract from the Esterhazy member, while IMC-Belle Plaine, near Regina, solution mines potassium chloride from both potash-bearing members.Ore from the Patience Lake member is a medium-grained mixture of sylvite and halite, with a KCl content of 36%, insolubles averaging up to 5.5%, and little or no carnallite.The ore from the Esterhazy member is a coarse-grained mixture of sylvite (KCl) and halite (NaCl) with a small amount of water insolubles, and some carnallite (a K-Mg chloride). Average run-of-mine grades are about 30% KCl."

Jan 1, 2003

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By K. Huang

"Solvent extraction (SX) is one of the most effective techniques for the multi-metal separation. However, repetitive pre-treatment of feed-in solutions and/or multi-steps two phase equilibrating in conventional SX processes were always unavoidable due to the poor separation selectivity between those metals with similar physicochemical properties. In this paper, our recent efforts, aimed to develop a “Three Liquid Phase Extraction” (TLPE) strategy for one-step separation and selective enrichment of different metals respectively into three coexisted liquid phases, are reviewed. Various feasible “Three Liquid Phase Systems” (TLPS) are evaluated. The TLPE technique provides a potential possibility for multiphase extraction to separate multi-metals.INTRODUCTIONLiquid-liquid Solvent Extraction (SX) is one of the most effective techniques for metal separation and purification. Traditionally, extraction and separation of multiple valuable metals from the leaching solutions of complex ores, industrial wastes and byproducts have to face such difficulties that multiple target metals with similar physicochemical properties co-exist in the solutions, and therefore their mutual separation selectivities are very poor. In conventional organic-water two phase SX processes, repetitive pre-treatment of feed-in solutions including the adjustment of the solution acidity, removal of impurities and/or multi-step liquid-liquid two phase equilibration were always unavoidable (Wang and Chen, 2001). Only one of the target metals is obtained in each extraction step, therefore the whole separation processes for multi-metal separation are typically very long and costly.Liquid-liquid-liquid three phase extraction is a developing technique for separation of complex systems containing multiple target components (Tan, 2003; Shen, 2006; Yu, 2009). The technique is in fact a three-liquid-phase selectively partitioning of different target components through the control of phase-forming behaviors of extraction system to create a unique separation medium with three co-existed liquid phases. The separation selectivity of “Three-Liquid-Phase System” (TLPS) may derive from its three-layered liquid phases from up to down with different hydrophobic or hydrophilic environment, and therefore each phase has its own specific selectivity for dissolving of an individual component. In a well designed “Three-Liquid-Phase System” (TLPS), multiphase extraction and selective separation of different components respectively into three different liquid phases can be achieved by only one-step of extraction. Owing to its distinct advantages, “Three-Liquid-Phase Extraction” (TLPE) technique has found many potential applications in purification of various organic chemicals (Shen, 2007) and biological activities (Chen, 2002; Tan, 2006; Jiang, 2008), treatment of environmental wastewaters (Shen, 2006; Yu, 2009; Yu, 2010; He, 2012), extraction of valuable components in natural products (Liu, 2010) and separation of multi-metals in complex leaching solutions (Jin, 2009)."

Jan 1, 2012

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By Selvia Tourn, Liliana Castro

"Abstract - Argentina, a large country with an important agriculture industry, needs an ever-increasing amount of phosphorus and potassium, as essential elements for plant growth. Current requirements are met from imports, but potential resources exist in Argentina. For example, several phosphatic occurrences are known in paleo-marine basins, the most significant of which are in Tertiary units in Patagonia. In addition, two types of potassium deposits are also known in Argentina: evaporite deposits in the Neuquén Basin at depths of 750 m to 1500 m contain 22 to 25 wt% K2O equivalent; and glauconitic sandstone containing about 6 wt% K2O has been identified in Patagonia.Several experiments were undertaken to test unprocessed phosphate rocks as slow-release, direct-application fertilizers, with good results. In addition, it is proposed that direct application of glauconitic sands would provide an efficient and economic alternative source of potassium. Tests with glauconite samples are still in progress. The existence of both phosphate and glauconitic rocks in Patagonia suggests that development of an extractive industry for these materials would not only help Argentina approach self-sufficiency in fertilizer usage, but also assist in the socio-economic development of this region."

Jan 1, 2003