Search Documents

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator's ear. Recommendations are made to increase the attenuation at the operator 's ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator's position was also measured."

Jan 1, 1986

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By J. Grant Spratt

THE Turner Valley gas-field, situated some thirty miles southwest of Calgary, Alberta, has been the topic of much discussion, particularly from a geological viewpoint. Several papers (1, 2, 3, 4, and 7) dealing with the structural and stratigraphical geology have already been published and are available for reference(l). In this article, the geological conditions will be treated only as they directly refer to the crude-oil prospects along the west flank of the anticline. HISTORY During the past twelve years, Turner Valley has been known mainly as a field which has produced a high-gravity naphtha from relatively large quantities of gas. For about ten years prior to the discovery of this naphtha-bearing gas, which is produced within the upper 450 feet of a dolomitic limestone of Carboniferous age, a minor production of light crude-oil was obtained from overlying sands of Cretaceous age. Up to June 1st of the present year, the field had produced 9,473,582 barrels of naphtha from approximately 829,000,000 M.c.f. of gas. For the past four years, the total daily production of 80 to 90 wells has averaged about 3,200 barrels of naphtha from 250,000 M.c.f. of gas. This is an average of 13 barrels per million cubic feet. The naphtha is extracted from the gas by ordinary gas-oil separators and absorption plants. After the naphtha has been recovered, about ten per cent of the gas is marketed for fuel to supply the cities of Calgary and lethbridge and intermediate cowns. The remaining ninety per cent is burned to the atmosphere, with the exception of some four to five million cubic feet per day which the Calgary Gas Company score in the depleted Bow Island gas-field.

Jan 1, 1936

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By J. R. Kadambi, J. Furlan, Kucukal E.

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV.INTRODUCTIONA hydrocyclone is a piece of equipment used to separate and/or classify solid particles or liquid droplets from liquid solid or liquid-liquid feed. Versatile in application, hydrocyclones have been widely used in industrial applications including the food, oil, power generation, chemical, and mineral processing industries. The first hydrocyclone was introduced in 1891 by Bretney to purify various liquids (Bretney, 1891). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2017

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By G. W. Neumann, J. R. Schnarr

The lead-zinc-copper-silver ores mined by Brunswick Mining and Smelting Corporation Limited at their No. 12 underground mine and No. 6 open-pit operation, and treated by distinct concentration processes in separate plants, present difficult metallurgical problems because of the extremely fine dissemination of the valuable minerals with pyrite and pyrrhotite. The problem of concentration is further complicated, in the No. 12 ore, by the presence of a varying content of graphitic carbon. This paper describes the milling of No. 12 ore and the production of copper, lead and zinc concentrates by differential flotation.

Jan 1, 1971

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015

By R. Hans

Removal of toxic anions from aqueous solution was studied using a Magnetic Ion Exchange (MIEX) resin which is a polyacrylic, strong base resin. Gravity based settling is made more efficient due to the magnetic nature of the resin which is advantageous over conventional ion exchange resins. In addition, the magnetic microspheres of MIEX have larger surface area in comparison to conventional ion exchange resins. Over the years MIEX has been successfully used and has gained significant popularity for efficiently removing dissolved organic matter from wastewater and groundwater. In the present study the efficiency of the MIEX resin was tested for the removal of chromium(VI), molybdenium(VI), vanadium(V) and arsenic(V) anions. Effects of pH (2-10) and temperature (25oC-55oC) were examined. In general, low solution pH values were favorable for anion uptake by MIEX. Except for chromium(VI), the metal ion uptake was significantly increased by the increase in solution temperature. The adsorption data were analysed on the basis of chemical speciation and heterogeneous kinetic models.

Jan 1, 2014

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By W. N. Roman

This paper will examine the challenges involved in ventilating and cooling South African mines, with particular emphasis on solutions to the issues of heat (generally associated with depth), mechanization and energy efficiency. Comparisons will be made with other international mining areas. Some of the deepest mines in the world are to be found in the South African goldfields. The Mponeng mine is approaching 4,000 m below surface, with virgin rock temperatures (VRT) of between 60°C and 70°C. Mining at these depths has only been possible with the use of large refrigeration plants supplying cold air, water and ice to the workings. In the Bushveld Igneous Complex, where most of South Africa?s platinum mines are located, similar VRTs are being experienced at significantly shallower depths. This is due to the different geothermal properties of the host rock between the two areas. Existing mines are being forced to go deeper and new underground mines are being planned and constructed in other areas with widely differing thermal conditions. South African metal mining has traditionally been labour intensive for historical reasons as well as for the narrow tabular nature of many ore bodies. Due to cost pressures and labour problems, some mines have been investigating the possibility of using mechanized equipment, both diesel and electric, to increase production and to improve efficiency. Studies have been carried out to determine the effect of the additional equipment on the overall ventilation system and some of the conclusions are discussed. The use of diesel equipment adds heat and pollutants to the ventilation air but, although electrical equipment has a lesser effect on the ventilation systems, it is generally less favoured due to claims of lower flexibility/manoeuvrability. Mechanization holds the promise of more concentrated mining activities but, with higher localized ventilation and cooling needs. Systems which will control the provision of air and cooling more effectively are required and are being implemented. In the 1990s and early 2000s, the South African economy experienced significant growth which was not matched by the growth in infrastructure. Consequently, at present there is a shortage of electricity generation capacity which affects large industrial consumers, including mines. Increasing levels of heat and mechanization will require more electrical energy for ventilation and cooling. There are many initiatives underway to save power or to shift consumption to periods of national low demand and these will be described.

Aug 1, 2013

By R. Lasmanis

"Washington State&apos;s diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995