Search Documents

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By Z. G. Tao, Y. Y. Peng, W. L. Gong, M. C. He

"This paper presents an overview of the major landslide hazards in open pit mines in China, the currently used landslide control and monitoring techniques, and development of a new slope control technique incorporating the reinforcement, sliding force monitoring, remote sensing and forecasting in one system in order to constrain the displacement of the sliding blocks in the landslide to minimized the influenced area and provide precise warnings timely for the imminent landslides. For implementation of the new technique, a novel rock cable with large deformation and high resistance (also known as HE cable) was developed, which can elongate as long as 2m. At the same time, the necessary and sufficient condition for initiating a landslide and energy balance equations are formulated. Based on the proposed mathematical models and Beidou satellite system, the software and data transmission hardware for remote sensing and forecasting were developed the new landslide control technique has been applied successfully in 245 landslide sites in 12 provinces across China. In this article, two practical application cases in the open pit mines are reported.INTRODUCTIONChina is one of the countries in the world with the most widely distributed landslides and suffering the heaviest damage. According to the incomplete statistics, landslide hazards have caused death of hundreds of people and direct economic losses of several hundred million RMB each year. The landslide hazards have a great impact on the life and property safety of the people, safety of the infrastructure, as well as the social stability. Thus development of new techniques for forecasting and prediction of the landslides is imperative and of great importance. In general, the forecasting and prediction of the landslides consists of three major aspects, i.e. sliding time forecasting, landslide activity intensity forecasting and landslide hazard degree forecasting. Since a considerable part of the landslide-suspected area are adjacent to the residential areas or important infrastructures, development of the advanced landslide control and monitoring techniques to cope with the sliding time forecasting problem is more important.Over the past one hundred years, the most widely used slope monitoring techniques are based on displacement monitoring (Xu, et al. 2007; Toshitaka, 1998). In the early days owing to the limitation of the technology and equipment, the ground surface displacement and underground water level change were inspected mainly by man power for inferring the possibility of a landslide. In recent several decades, more and more ground surface displacement monitoring devices were brought to the market, such as the automatic total station, theodolite, digital level, borehole inclinometer and GPS based instruments, etc. Based on these modern techniques, some advanced instruments have been developed and applied to the landslide monitoring, for example, the “landslides early warning monitoring system” (Leonardo, et al. 2002), the “In-SAR” technique (Reevea, et al. 2000), the GPS and satellite geodetic survey based technique (Reevea, et al. 2000), and real-time telemetry technology (Xu, et al. 2007). These monitoring approaches have made significant contributions to the landslide disaster monitoring and forecasting. The major limitations for the ground surface displacement monitoring techniques are lie in the inconsistence between the displacement in ground surface and that in the sliding surface for the sliding mass, resulting in low degree of forecasting accuracy."

Jan 1, 2015

By L. H. Bergmann

THE blasting practices described are fairly representative of those employed in the coal mines of Eastern Canada. As such, they may be of interest to Western Canadian coal mine operators. The treatment of the subject is general, no attempt being made to discuss blasting operations at any particular coal mine in detail. All the mines dealt with are mining bituminous coal and are classified under the Coal Mines Regulation Act of the Province of Nova Scotia as 'closed light' mines. As such, they are required to use only 'permitted' explosives and to apply them in a 'permitted' manner, except where authority is given by the Mines Department to do otherwise.

Jan 1, 1945

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By Xuanxue Mo, Kaihui Yang

"Abstract- The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Barly Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry . The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affinities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental rnicroplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820Jo Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 g/t) and recoverable amounts of Au, Tl, Gd, Ga, Ge, In. A massive sulflde zone, in which lenticular and stratiform orebodies are localized in a sulflde-carbonate-silica shale unit or sulfldic tufflte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulflde zone developed in a subvolcanic intrusion or volcanic sequence. The sulfide mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite- chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerais occur rarely in the massive ores. The massive ores are generally fine-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and dis­ placement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two dis­ tinctive alteration zones have been identified: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, trema­ lite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive mode! of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By P. Roman, L. Daneshmend

"During the last decade, mining companies have been overwhelmed by technological solutions to perceived problems. This is particularly true with information technology where rapid advances have resulted in a professional climate characterized by technomania — the perception that failure to adopt emerging technologies will result in a loss of competitive advantage. This paper describes the applicability of structured analysis and design techniques as an appropriate methodology for integrating emerging technologies in the mining industry. The potential of this approach to improve overall mine effectiveness through improved communication and co-ordination between operations and maintenance is discussed. IntroductionA strong working relationship between the operations and maintenance departments in both open pit and underground mines is fundamental to the overall success of the mining endeavour. Unfortunately, for many mines, this characterization is far from accurate. Short-range production targets dominate the day-to-day management of the mines. This can be seen in Bostwick and Buchanan’s (1993) report on American Barrick Resources efforts to achieve an aggressive 415 000 tpd mining program at their Goldstrike operation in Nevada. When production managers do not meet their quotas, the finger is often pointed at maintenance. As a result, a confrontational culture can develop between the two organizations, resulting in a lack of cooperation that exacerbates the problem. Historically, production planning has taken priority over maintenance planning. This is reasonable since production is the primary purpose of the mine with maintenance serving in a support role. This basic relationship remains intact today. However, the trends toward mechanization, increasing levels of automation, and larger equipment, have resulted in increased reliance on the equipment used in the mine. As a result, downtime costs now go well beyond the direct labour associated with the repair of the machine. Lost production costs due to downtime resulting from failed equipment are becoming an increasingly important factor in determining a mine’s overall economic performance."

Jan 1, 2001

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

?Founded in 1969 by the Ruia family ?Diversified global business corporation with a balanced portfolio of assets in the manufacturing and service sectors; $15 Billion revenue in FY 2009-2010 ?Employs 70,000 people worldwide with offices in Asia, Africa, Europe and North America

May 1, 2011

By Claude Hubert, Robert Sansfaçon

"The Malartic gold camp includes the Malartic Gold Fields, Barnat, East-Malartic, Canadian Malartic and Sladen mines. From 1935 to 1984, these mines have yielded 212 403 kg of gold. They occur within a 900 m wide belt of highly sheared, dislocated and faulted volcanic and sedimentary rocks (Piché and part of the Pontiac groups) herein named the Malartic Tectonic Znne (MTZ). The zone trends WNW-ESE and separates two lithotectonic sedimentary domains, the Cadillac to the north and the Pontiac to the south. The sedimentary domains are characterized by their coherent fold generations consisting of open to tight reclined and recumbent F1 folds that have been refolded into series of asymmetric upright F2 folds. A flat-lying schistosity (S1 ) and a vertical pressure-solution cleavage (S2) are ubiquitous throughout. Discrete sets of brittle and brittleductile faults are synchronous and parallel to each of these two fabrics.The MTZ trends N320° in the northwestern sector of the town of Malartie, changing to N2800 at its easternmost extremity. The Malartie and Sladen faults constitute its northern and southern boundaries respectively. These two faults also bound another set of faults oriented N305°. Throughout the MTZ, the faults at N280° and N320° and those at N305° outline a series of anastomosed motifs that constitute the principal structural feature of the Malartic district. Locally, a fourth set of minor faults at N065° combines with the other three prominent sets. All these faults have disrupted the gold-bearing volcanic, sedimentary and intrusive rocks encountered throughout the MTZ.The MTZ comprises numerous lozenge-shaped blocks of komatiites and basalts or greywackes and black shales which are cut by disjointed dikes, sills and small intrusions of felsic and mafic rocks. The latter includes gabbro, diorite, lamprophyre, monzonite and pegmatite. They frequently fill conjugate sets of fractures. In some areas, they are clustered into coalescent intrusions. The present morphology of these intrusive bodies( cube, chocolate-tablet boudin, parallel epiped and cigar) is not representative of their primary forms but the result of late shearing and faulting indicative of a major tectonic event subsequent to their emplacement. The intrusions were injected during a brittle stage of deformation related to the F1 folding but prior to the development of the F2 folds and subsequent tearing and shearing by late brittle and brittle-ductile faults . The ultramafic and mafic rocks are intensely altered to serpentine, tremolite, actinolite, carbonate, biotite, hematite and pyrite according to the nature of their proto/it h. In the vicinity of the MTZ, all lithologies exhibit mineral assemblages indicative of the upper greenschist or lower amphibolite facies of metamorphism.The structural evolution of the MTZ involved superimposed folding, shearing, transposition, mylonitization, brittle and brittle-ductile faulting. Each lenticular motif results from the combined effect of conjugate sets of shear zones that outline lozenge-shaped blocks where strain markers indicate different strain states from cores to margins. Bedding in ultramafic flows and/or sedimentary rocks is either NW-SE or NE-SW within the blocks but, in the vicinity of the Malartie and S laden faults, it has been rotated to become subparallel to the faults.Ore shoots are most commonly associated with altered and deformed bodies of diorite and monzonite, or some mafic and ultramafic schists and, at the Canadian Malartic, Sladen and East Malartic mines, with metasedimentary rocks. The shoots occur in close proximity to the various faults of the MTZ but the gold itself is intimately associated with pyrite, biotite and carbonate in halos bordering fractures crisscrossing the different host rocks. The density of fractures and the width of their altered zones have been significant parameters in the production of economic ore shoots. Grains of gold are visible in some veins of quartz a"

Jan 1, 1990

By K. Turgeon, D. Larivière, L. Whitty-Léveillé, J. -F. Boulanger, C. Bazin

"The processing of ore containing rare earth elements leads to the production of an impure solution of these elements. The separation of the rare earths from the impurities and the production of individual elements is usually carried out by solvent extraction. The effectiveness of the extraction conditions and of the reagents is generally tested in the laboratory. This paper deals with the processing of results from solvent extraction laboratory tests planned to generate data redundancy. A method is proposed to take advantage of the data redundancy by accounting for the pH variation during the extraction. The parallel processing of several tests also allows estimating the equilibrium constants for the extraction. The proposed method produces equilibrium constants that are more reproducible than values estimated using conventional approaches. The method is illustrated with solvent extraction tests conducted on synthetic solutions of rare earth elements.INTRODUCTIONThe processing of ores containing rare earth elements (REE) usually includes the production of a concentrate of the minerals carrying the REE. These minerals, for instance monazite and bastnäsite, contain the 14 elements from La to Lu plus yttrium and scandium. As an example monazite has the general formula of (La,Ce,Pr,Nd,Sm,Eu,Gd,Tb,Dy…Lu)PO4 with a typical lanthanum content of 20-26%, cerium content of 40-50%, praseodymium of 4-6%, neodymium of 16 to 20%, and decreasing concentrations of heavier elements (Gupta & Krishnamurthy, 2005). During the processing of a REE mineral, it is generally not possible to isolate and separate a single REE from all the rest. The mineral molecules need to be broken (usually via a heat treatment followed by leaching with a base and/or an acid) to produce an aqueous solution of the REE of the ore. After purification of the solution, the REE can be precipitated as a bulk concentrate and sold to a refinery that separates the REE into particular groups of REE such as the light versus heavy REE or into individual elements such as lanthanum, neodymium, or europium oxides to yield value-added products."

Jan 1, 2016

By D J. McDougall

Due to changes in the solid-state conditions of minerals in the rocks surrounding hydrothermal, contact meta-somatic or metamorphosed ore deposits, positive or negative thermoluminescent anomalies may be found in their vicinity. Several types of equipment which can be used for both quantitative and semi-quantitative measurements of the emission are discussed and compared. Methods of selecting, preparing and testing samples to ensure reproducible results are outlined, along with the kind of data which can be obtained from different types of equipment. The normal thermoluminescence of rock-forming min~ erals in the common rock types is noted, and variations in the solid-state conditions in the wall rocks which will cause marked increases or decreases of true thermoluminescence are outlined, as well as the thermolum-nescence-like emissions which are present in the vicinity of ore deposits. Introduction T HERMOLUMINESCENCE occurs when certain crystalline materials are heated to temperatures ranging between 180' and 400°C. The light emission can be ascribed to the release of electrons metastably trapped within the crystal lattice, with peak emissions taking place at temperatures which are more or less specific for a particular set of traps; the area under

Jan 1, 1965

By R. J. R. Schaller

NO. 3 winze, the sixth shaft to be sunk on the San Antonio property, is practically a duplicate of No. 3 shaft, which was the main shaft prior to the installation of the larger hoisting equipment in 1939. It is collared on the tenth, or 1,500-ft., level, and goes down vertically to the sixteenth, or 2,500-ft., level, with a loading pocket, spill pocket, and sump below this. It is 1,000 feet east of No. 3 shaft. All ore, men, and materials are handled through the latter. The winze location with reference to the rock formation is shown in Figure 1. (In plan, this section strikes N.30°E. and cuts most of the main orebodies of the mine normal to their strike.) It is collared eighty feet inside the footwall contact of the basalt and cuts through it before reaching the eleventh level. In this location there will be no ore tied up in shaft pillars, as the closest ore to the shaft is on the tenth level, and here it is eighty feet northeast of the collar. The winze headframe and hoist-room straddle the main haulage to the No. 3 shaft, on the tenth level (see Figure 2). At no time during the excavation for the headframe and hoist-room was the general routine work of this haulage held up.

Jan 1, 1941