Search Documents

By D. Beneteau, L. Feldman, D. Milne, A. Hyett, G. Snell

"Behaviour of rebar bolts subjected to combined shear and bending in underground potash mining applications is not well understood. An experimental investigation compared load applied to resin-grouted No. 25 metric rebar to theoretical load, calculated using elastic bending theory. Distributed optical sensing (fibre optic) technology allowed axial strain measurements at 1.25 mm increments along the length of rebar. Experimental procedure, data processing methods, and equipment improvements are needed for field applications of optical sensing technology. Goals were to adopt procedures for instrumenting rebar bolts, conduct tests, and develop data interpretation methods to measure field deformations and loads. ¦ KEYWORDS Fibre optic, Potash mine, Rebar bolts, Transverse load testing RÉSUMÉ On appréhende encore mal le comportement des boulons d’ancrage pour barres d’armature soumis au cisaillement et au cintrage pour un usage dans des mines de potasse souterraines. Une étude expérimentale compare la charge appliquée aux barres d’armature de diamètre n° 25 (25 mm en mesure métrique) enduites de résine époxy à la charge théorique, calculée à l’aide de la théorie de la flexion élastique. La technologie de détection optique distribuée (fibre optique) a permis d’effectuer des mesures de la contrainte axiale à des différentielles de 1,25 mm sur toute la longueur de la barre d’armature. Pour des applications sur le terrain de la technologie de détection optique, il faut envisager une procédure expérimentale, des méthodes de traitement de données et une amélioration de l’équipement. Les objectifs établis consistent à adopter des procédures d’instrumentation des boulons d’ancrage pour barres d’armature, à effectuer des essais et à mettre au point des méthodes d’interprétation des données pour mesurer les déformations et les charges sur le site. ¦ MOTS CLÉS boulons d’ancrage pour barres d’armature, essai par charge transversale, fibre optique, mine de potasseINTRODUCTION Resin grouted rebar bolts are commonly used in potash mines in the province of Saskatchewan, Canada, in areas where shear deformation is observed in the rock, or where potentially unstable ground is present, including locations such as clay seams. Opportunities to observe deformations of rebar, as shown in Figure 1, are rare because it is unusual in underground potash mining to excavate supported ground. In this situation, a block of potash containing a rebar bolt had failed."

Jan 1, 2019

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By X. S. Yuan

With the production increase of Oil Sand in Fort McMurray Alberta, more efficient tailings disposal has become a priority for Syncrude Canada Ltd. A lot of work on tailings research and development has been compiled to determine the most effective deposition to increase reclamation options, water re-use and thermal energy recovery. Efficient flocculation of fine oil sand tailings is the key technology for thickening. It was identified that flocculation of fine transition/marine ore tailings using a single flocculant was not effective. The thickener overflow contains 1-4% solids content compared with the target solids content of <0.5% obtained with Estuarine ore. As a result, novel processes for treatment of fine transition/marine ore tailings have been developed at Syncrude Bitumen Production Development since June 2004. While the conventional processes using a single flocculant, a single coagulation, or a coagulant-flocculant combination was ineffective for transition and marine ore tailings, the new processes including Coagulation-Flocculation-Coagulation (CFC), Flocculation-Coagulation (FC) and Flocculation-Coagulation-Flocculation (FCF) were acceptable options. The key components of these technologies consist of the recipe of chemicals and their adding sequence. With these technologies, almost all sub-micron clay minerals are aggregated together and settle as a whole, resulting in a clear supernatant of less than 0.1% solids.

Jan 1, 2006

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By R. C. A. Thurston

AT A FATIGUE SESSION organised by the A.S.T.M. in 1949, R. E. Peterson presented a brief introductory paper ( 1) in which lie referred to a discussion on the fatigue of metals which took place in England in 1849, and then proceeded to review some of the subsequent researches concerning the mechanism of fatigue. In the course of the review, he discussed metallograpl1ic studies with single crystals and polycrystalline materials, studies with X-ray methods, and the application of the electron microscope. During that hundred-year period considerable progress was made toward a better under-standing of the nature of fatigue, although it is probable that even greater attention was directed to the more practical aspects of the problem, such as the effects of notches, temperature, corrosion, surface treatment, residual stresses, and so on. Since then there has been an appreciable acceleration in the tempo of the fundamental work, partly influenced by the rapid development of the theory of dislocations, with the result that our knowledge of the mechanism of slip, the initiation of fatigue cracks, and their subsequent propagation, has still further advanced, although it is by no means complete as yet. The present paper is an attempt to out-line the more recent developments in these basic studies, to correlate them when possible, and to draw attention to those directions in which research might profitably be pursued.

Jan 1, 1957

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By P. H. Oliver

"The current theory of how explosives fracture rock offers no explanation for the improvements in fragmentation and the reduction of fly rock and back break which occurs when an adequate inter-row delay time is used. Nor does it explain why fragmentation improves with rectangular drill patterns where the hole spacing may be as much as four times the hole burden.A new theory of rock fragmentation is proposed which builds on the existing theory. It offers rational explanations for the many blast effects which the current theory does not address and the need for adequate timing delays between rows. It improves on the design of inter-row delay timing by defining the length of free-blasted face needed in front of a hole *Retired from Inco Ltd., Sudbury, Ontario when selecting the delay element which will provide an adequate inter-row delay time."

Jan 1, 2003

By P. H. Oliver

The current theory of how explosives fracture rock offers no explanation for the improvements in fragmentation and the reduction of fly rock and back break which occurs when an adequate inter-row delay time is used. Nor does it explain why fragmentation improves with rectangular drill patterns where the hole spacing may be as much as four times the hole burden. A new theory of rock fragmentation is proposed which builds on the existing theory. It offers rational explanations for the many blast effects which the current theory does not address and the need for adequate timing delays between rows. It improves on the design of inter-row delay timing by defining the length of free-blasted face needed in front of a hole when selecting the delay element which will provide an adequate inter-row delay time.

May 1, 2003

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By Dean McDonald

The Committee Bay Greenstone Belt extends over 300km and is one of the largest unexplored greenstone belts in North America with excellent gold and diamond potential. Committee Bay Resources Limited holds over 550,000 acres of land with prospective geology in the Committee Bay area southwest of Melville Peninsula, Nunavut. Committee Bay is a typical Archean greenstone belt comparable to the Yellowknife, Red Lake, Kirkland Lake and other prolific gold belts. Drilling during 2003 at Committee Bay resulted in: 1) the discovery of high-grade gold-bearing quartz veins with silicification and sulphidation at Three Bluffs, and 2) the continuation of high-grade gold mineralization in the hinge area of the iron formation at Inuk. Gold mineralization at Three Bluffs is identified in iron formation and adjacent sediments and has been traced by drilling for over 700m. The Three Bluffs iron formation is open to depth and along strike where is has been traced on surface for over 6km. In January 2004 Committee Bay and joint venture partner Gold Field?s announced a $7.1 million exploration program for the Committee Bay project in 2004. A total of 8,000m in exploration drilling has been approved for the expansion of the Three Bluffs to the resource stage and drilling of at least five new target areas. Additional mapping, sampling and geophysics will be used to identify new gold targets along the very prospective Committee Bay belt.

May 1, 2004

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee&apos;s field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By S. McPhail, D. Richardson, G. J. Simandl, C. Akam, S. Paradis, M. Yakimoski, A. Teucher, Y. Cui, F. Ferri

Historically, extracting dissolved solids from formation water was economically motivated. Today, main drivers are environmental benefits and regulations, as large volumes of water needed for hydraulic fracturing require treatment before reuse or disposal. The concentration of dissolved solids in flowback water increases with each use and may require treatment prior to disposal. Element recovery from produced water is not profitable unless market conditions are favourable, recoverable elements are abundant, and economical recovery methods are established. Sale of recovered materials could offset recycling and disposal costs. This paper describes markets for Cl, Na, Ca, K, Sr, Mg, Br, Ba, I, B, and Li, and their concentrations in produced water from oil and gas wells in British Columbia. It recommends revising sampling protocol for produced water.

Jan 1, 2018

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003