Search Documents

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By C. J. Martin, M. P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist.To date the performance of more than 20 flotation plants has been predicted, including copper, lead, zinc, phosphate, pyrite, graphite, cassiterite, platinum, nickel and various slags. The method has successfully been used to predict and size four flotation plants directly from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted.The technique has now received broad acceptance within the South African mining industry, for example in the last year alone it has been used to drive flowsheet development for at least seven new plants. It is also being used to assist in the optimisation of existing operating plants.The methodology is described in this paper and verification of the methodology is presented using case studies of porphyry, polymetallic and PGM operations.INTRODUCTIONThere is considerable interest these days in the use of modelling to simulate flotation circuits, for process design and plant optimisation purposes. Although these models are proving to be useful tools for plant design and optimisation, their complexity can make them cumbersome – expensive to use and difficult for metallurgists to visualise and mentally absorb, without a background in each specific technique. In “SUPASIM” no attempt is made to measure flotation fundamentals, rather to use empirical relationships between laboratory flotation kinetics and plant performance – relationships that hold up well to validation exercises as will be demonstrated later in this paper. Although not designed to be as comprehensive as other models, “SUPASIM” is easily understood by the operating metallurgist and can be quickly and easily applied."

Jan 1, 2004

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By A Palynchuk

The development of welded pipe has paralleled the general industrial development and, in particular, that of the petroleum industry. The petroleum industry's need for high-grade, economical pipeline material to make many 'of its projects feasible has been a significant factor in the development of light-wall, high-grade welded pipe. The modern welding processes, such as high-frequency, electric resistance, flash, submerged arc, etc., have some basically different characteristics. The modern high-frequency weld mill is a complex of specialized equipment that is integrated into a production unit. Each component in the unit performs a specific function in the production process. Quality control must be built into the process on an operating basis and, to maintain the quality required for pipeline standards, must be more than a policing operation. The further development of the welded pipe industry will be determined by changing and increasing demands. The technical and economic views and requirements that will influence the development have to be resolved.

Jan 1, 1964

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By R. E. Martin

"The Westerose Leduc (D-3) pool, a Devonian reef reservoir situated in Central Alberta, Canada, has now been producing for over seven years. As a unit operation, the pool pro-vides an interesting example of the full exploitation of gravity segregation tendencies. The reef has a 238-foot oil column, underlain •by bottom water and over-lain by a substantial gas cap. The original hydrocarbons in place were 147.96 million STB oil and 94.4 MMMCF of Taw gas cap gas. Nine-teen producing wells on 80-acre spacing have been completed, most of which are highly productive. Gas injection operations return solution gas to the gas cap. A study of the rock and fluid properties of the pool show it to be conducive to production by gravity segregation at high rates. Monthly average producing rates have varied between 800 B/D and 8,000 B/D and have recently totalled 3,000 BID to 5,000 B /D. Recovery and performance predictions under partial pres-sure maintenance at 10,000 BID indicate an ultimate recovery of 66 per cent of the original oil in place. In the absence of pressure maintenance, recovery would be only slightly less."

Jan 1, 1960

By Fathi Habashi

"A process is proposed for the treatment of phosphate rock for the recovery of uranium and the lanthanides. The process assures the production of phosphatic fertilizers without polluting the environment with radioactive material.IntroductionWhile many processes for uranium recovery from phosphoric acid produced by the H2S04 route are known and utilised commercially, little is known about uranium recovery from phosphoric acid produced by the HN03 route1. Advantages of the latter route are both the elimination of the gypsum disposal problem, and the possibility of radium disposal in a controlled way2. Further, the lanthanides originally present in the rock can be recovered if the nitric acid route is used; they will be mostly lost in the gypsum produced by the sulphuric acid route3. In the present work a scheme for the recovery of uranium and the lanthanides from phosphate rock without interfering with the normal route for fertiliser production is proposed using HN03 as a leaching agent. Attention was also given to uranium decay products and their separation so that they might not contaminate the fertiliser4. Further, an attempt was made to defluorinate the leach solution in order to upgrade the fertiliser and at the same time recover the fluorine5. Rapid analytical methods for the determination of uranium, radium, and lanthanides in phosphate rock were developed6,7."

Jan 1, 1997

By J. R. Eastwood

"H.D.P.E. Piping in the Mining IndustryThere has been much use· ms.de of high density polyethylene pipe in the mining industry over the past several years. This is not only in new installations but al.so in areas where other piping materials such as wood, transite, concrete and steel have worn out and failed.The uses of H.D.P.E. in the mining industry are as follows:Tailings disposal linesMine water supply linesTailings water return linesHydraulic backfill linesPit drainageCorrosive liquid supply and disposal linesH.D.P.E. pipe has many advantages for both underground and above ground installations. It is tough, flexible, weather resistant and inert which makes the pipe suitable for many installations."

Jan 1, 1975

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

By J. A. L. Henderson

THE potential oil-and gas-bearing area with "which this paper deals is the large undefined Carboniferous basin, roughly triangular in shape, occupying about 10,000 square miles of southern and eastern New Brunswick. Its base, about 135 miles long, lies on the gulf of St. Lawrence and embraces the whole eastern coast-line of the Province, while its apex lies in the south-west corner of the Province, near the International boundary (see map, Figure 1). The Carboniferous basin may be divided roughly into two areas-the Northern basin and the Southern basin-by a structural feature represented by a ridge of low hills running north-easterly from the Saint John river, near Saint John, on the southwest, to Indian mountain, about eight miles north of Moncton, in the northeast. Within the Northern basin, all evidence regarding the presence or attitude of the older Mississippian Albert Shale series, the only oil-bearing rocks known in New Brunswick, is for the greater part obscured by a thick and practically horizontal blanket of Pennsylvanian strata and, although evidences of oil and gas have been reported, none has been positively identified. Five parallellines of gentle folding, running to the northeast, occur in the Pennsylvanian rocks, within a distance of 100 miles from north to south. This folding is reflected in the courses of the rivers, which lie within the synclines. The relationship of the folding in the younger rocks to structures in the uncomfortably underlying older rocks is unknown, but should now be possible of clarification by means of a geophysical survey accompanied by drilling. Independent geological examinations have yielded no evidence of value in this respect, nor have five exploratory boreholes drilled by per-cussion tools to a maximum depth of 3,645 feet been of assistance, as only one inconclusive hole completely traversed the beds which normally overlie the Albert shales.

Jan 1, 1940

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By Norman O. Lotter, Simon Yu, Tony Deng, Antonio Di Feo

"Xstrata Nickel’s Raglan operation, northern Québec, achieved paymetal recovery gains in 2007 by switching the collector from potassium amyl xanthate to sodium isobutyl xanthate. To follow on from that position, Xstrata Process Support (XPS) and A. Di Feo of Raglan proposed that a mixed xanthate system be formulated and tested towards further performance gains. This work selected ethyl and isobutyl xanthates as the candidates. An optimized ratio of these was to be determined by a designed experiment. This suggestion was based on an abundance of published literature that reported mixed collector systems outperformed single ones. A partial factorial design was used to configure four test conditions and a mid-square for the flotation work. The testwork was conducted using High Confidence Flotation Testing. The raw data were analyzed and modelled by Design-Expert software. An optimum ratio of 1.6:1.0 by mass (1.32:1.0 in molar terms) of isobutyl:ethyl xanthate was determined. Without this modelling, the optimum ratio would have been missed. Results obtained with the new baseline flotation test using this optimized mixture showed a 3.3% Ni recovery gain in the bypass concentrate and more than 1% recovery gain for PGM over the single PIBX system. This system has been proposed for and accepted as a plant scale trial in the first half of 2010.INTRODUCTIONConcentrator OperationsMilling and flotation of sulphide ores ahead of smelting and refining is a common practice. This choice results in the larger and more variable paymetal loss in the production of saleable metal [Cramer, 2001]. For this reason, it is common to see an ongoing performance improvement programme at the operations level. When successfully performed, these e"

Jan 1, 2010

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By M. Leroux, P. Lacombe, S. R. Rao, J. Y. Kim, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

"Laboratory investigations on two complex ores, the A1 zone ore from Les Mines Selbaie and the Lyon Lake ore from Mattabi Mines Ltd. (Division of Noranda Minerals), have been carried out to determine some of the main variables in collectorless flotation. In particular, the effect of pulp potential (controlled by gas composition), conditioning time, pH and grinding media have been studied.Chalcopyrite showed the greatest response to collectorless flotation among the four major sulphide minerals present, followed by galena. Flotation of sphalerite was variable from minimal to important depending on the mineralogy and the pre-treatment performed. Appreciable silver recovery was achieved collectorlessly for the Lyon Lake ore while it could not be achieved for the A1 zone ore of Les Mines Selbaie. It appears that the difference between the two ores is related to silver's predominance as tetrahydrite in the Lyon Lake ore while it is as argentite and native silver in the A1 zone ore.The response of the ores to collectorless flotation is strongly dependent on the pulp potential, Ep, and pH. Using different gas compositions and different conditioning times it was found that collectorless flotation occurs when Ep is +195 to +295 mv (vs SHE). The actual on-set potential for collectorless flotation is dependent on the ore. A too high potential or prolonged oxidation leads to a decrease in selectivity. Some other factors were examined, notably the effect of pH and the type of grinding media on the selectivity achieved in the laboratory.Preliminary results from a plant trial at Mattabi Mines Ltd. confirmed that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Collectorless flotation was not attempted at Les Mines Selbaie. However, examination of the distribution of collector between the different addition points in the copper circuit suggests that it may be present."

Jan 1, 1990

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By R. Tipman, T. C. Burnett

"A general computer program has been written to calculate material balances using multiple regression techniques. The program can handle metal assays or size distribution data obtained in multiple surveys of the flotation circuit. The ""best fit"" weight split is calculated between the input and product streams by minimizing the sum of squares of the residual errors using all of the available data. The program includes an assay adjustment feature in which each assay is recalculated to fit the ""best fit"" mass balance. Thus assay or sampling errors can be easily identified. Also the assays can be statistically weighted so the most precise measurements are given the most influence on the material balance. The computer output reports the mass balance, the actual and corrected assays, the percent metal recoveries and the significance and confidence levels for the weight splits.The program enables a rapid and accurate evaluation of mass balances from large masses of data obtained in multiple surveys around a flotation circuit. The effects of changing process variables can be quickly evaluated with statistical confidence."

Jan 1, 1978

By Louis Frost

MINE ventilation has for many years been the subject of intensive study by numerous investigators who have presented their findings in forms that are understandable to the average mining man, and all this writer hopes to do is to review those findings in relation to the 'manager's' problem in mine ventilation. It would not, perhaps, be wholly correct to acclaim practical mine ventilation as an exact science, because of the many variables entering into the problem. Each mine has its own particular problem and ventilation characteristics. Fan design, in contra distinction to mine ventilation, is an exact science, but the designer cannot always take into proper consideration the practical variations to which each mine is subject. Fan designers, accordingly, are forced to base their design on such data as the mine manager or engineer is able to supply, and, when it is borne in mind that the mine characteristic is constantly changing, it is not at all surprising that fans do not always show efficiencies hoped for. In many instances, fans work far beyond the de-signer's limitations, and, in consequence, are an economic disability in the colliery cost-sheet, and it is of paramount importance that the colliery manager evaluate all the factors involved in relation to fan performance for the colliery to receive full benefit from its investment.

Jan 1, 1941

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986