Search Documents

By T Akiyama, J A. de Castro, H Nogami

Blast furnace is a countercurrent moving bed reactor that produces pig iron from iron bearing materials like pellet, sinter or lump ore. The furnace has cylindrical shape and the lump solid materials are alternatively charged onto the top of the furnace. Hot air is introduced through tuyeres that are set on the lower furnace wall. Auxiliary fuels (pulverised coal, oil or natural gas) and raw materials (fine ore or fluxes) are injected into the furnace with blast air from the tuyeres. In front of the tuyeres, coke particles react with oxygen in the blast air and generate carbon monoxide. The hot reacting gas heats up the lump solids and reduces iron oxides in the upper furnace. In the middle height of the furnace, the reduced iron and slag are fused by the combustion heat and form the cohesive zone. The molten iron and slag that are generated in this region trickle down through the packed bed of coke particles and flow into the bottom of the furnace. Therefore, the flows of gas, lump solids and liquids exist at the same time in the lower part of the blast furnace.

Jan 1, 2000

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

A key premise to this paper is that most people involved in the design and implementation of drilling and blasting operations could benefit from a greater understanding of the geological materials, deposits and landforms they are dealing with. The second key ingredient for successful blasting is the concept of blasting objective. Mine operators and blasting contractors must be clear on what drives their costs (blasting leverage) and should formulate blasting objectives and operational targets which help in this regard. Many operators ignore geology descriptors and features apart from the name of the rock and start crudely quantifying the rock mass properties in terms of uniaxial compressive strength, or even worse still as hard or soft. This occurs too early in the design process and not much attention is paid to the geological materials, geological structures and the characteristics of the deposit they intend to excavate. In effect the rock type name and the strength descriptor become the site geology. Furthermore many blasting operators do not formalise their blasting objective, do not set operational targets and do not measure results to the degree required for continuous improvement. In this paper a number of civil, surface mine and underground mine blasting applications are tabulated in terms of typical blasting objectives and common geological materials. A good description of geological materials can convey a lot of useful information for blasting operators if they are able to accommodate this knowledge. In addition a clear statement of the blasting objective and associated operational targets will maximise the likelihood of achieving blast-driven downstream productivity improvements. The æStarting at Both EndsÆ combination is deemed extremely useful for any continuous improvement blasting program.

Jan 1, 1999

By P Cepuritis, G Chitombo a, I Brunton

There is a significant amount of past evidence that links blasting and occurrences of slope failure. Particularly of great concern at Telfer Gold Mine is the effect of open pit blasting on the stability of the footwall slope above the underground portal and the stability of underground structures. For this reason, Newcrest Mining Ltd invited JKMRC to conduct necessary field measurements and numerical modelling with the following objectives:assess the dynamic stability of the footwall slope above the portal; assess the characteristics of current and future blasts in the open pit; and prepare open pit blasting guidelines that will minimise the detrimental effect of blasting on slope stability. To achieve these tasks it was necessary to develop a scaled distance attenuation curve for blast vibrations. In order to validate the developed vibration attenuation curves it was necessary to monitor vibrations from a production blast. Using JKMRC blast design software tools, the vibration of the production blast was also modelled from the blast design and vibration results from single hole blasts. The intention was, assuming that the observed and modelled vibrations were close in terms of frequency and amplitude, to use the software tools to model the vibrations of future blasts and assess their likely effect on slope stability. Numerical modelling of the dynamic stability of the footwall slope was done using the FLAC finite difference code and the UDEC distinct element code. The results of the numerical modelling and of the field measurements of the blast induced ground vibrations were combined into the blast design rules that relate distance between the slope and the blast, charge weight per delay and number of blasts necessary to cause failure of the slope.

Jan 1, 1999

To the south and west of Broken Hill lies the Thackaringa silver-lead district, about 25 miles, and is the locality really of the first silver find in the country long before Broken Hill, the geological fomations of which it much resembles. The Iocks and their structure are identical, except that in this area they are  more irregularly foliated and apparently much more faulted and expose in places quick successions of complete anticlines and synclines, even in a single lease. Saddles of ore respectively are found coinciding with the flexures of the rock but many minor veins otherwise and branches exist and make connections which render the whole a mining problem. It follows then that the surface.of the ground after some denudation in dotted with croppings of all the series, and in such a confusing way that the actual strike of a vein may be even confounded with the dip and readily mistaken for it at a few places. The main character of the outcrops are those usual in the district consisting almost wholly of argentiferous and silicious ironstone, sometimes gossan, which at a depth in a few feet changes to a gangue of very silicious carbonate of iron (crystallised), which occurrence is uniform through this district.The exploration of the lodes has not been extensive as it has not been well understood. Shallow shafts and drives have comprised nearly all the mining at present, which is evident on first sight by the numerous shafts and small excavations dotted 'about, as in an alluvial field. The depth of exploration underground in one place had gone several hundreds of feet, never more than 150 feet vertical from the surface in depth and irregular. The undulations of the most continuous work in this direction is such that it presents at different places successively either a tunnel, shaft, underlay winze, level, or Tise, and is on ore all the time, and where the rocks are faulted (which occurs as much as 30 feet and more) these changes are very abrupt, but for working on are suitably connected by the management.

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By R Dunne, D Yan

In flotation where a bulk flotation concentrate is produced or a gangue sulfide such as pyrite contaminates a concentrate, residual collector has to be removed from the sulfide surfaces to allow selective separation in a subsequent flotation step. Depending on the sulfide mineral, the main species that needs to be removed when using a xanthate collector is either a metal xanthate or dixanthogen. For the identification of surface species, specific solvents may be used to remove each species û metal xanthates are known to be soluble in acetone whilst dixanthogens are known to be soluble in non-polar solvents such as diethyl ether. Xanthates break down with time, temperature and pH into various decomposition products. The major decomposition product is dixanthogen which can aid flotation but other products such as perxanthate and carbon disulfide can have an adverse effect on flotation. Various analytical techniques can be employed to monitor the formation of decomposition products on the surface of the mineral and in solution. The best of these is ultraviolet spectroscopy as it has diagnostic peaks for decomposition product determination. In this work two approaches were taken to understand the relationship between the flotation of a chalcopyrite and pyrite from an ore containing these two minerals. One approach was to remove the xanthate species with an organic solvent and then use ultraviolet spectroscopy to determine the concentration of dissolved species. The second method involved measuring xanthate decomposition in solution by measuring the residual xanthate concentration using ultraviolet spectroscopy. These experiments confirmed the species adsorb at the surface of the mineral and how these species affect the recovery and grade of the valuable mineral. In both cases pH and temperature were varied and two xanthate collectors (SEX and PAX) were used to study these relationships. These relationships could be applied to industrial flotation systems and allow for more accurate determination of optimal xanthate dosage and hence save on reagent costs.

Jan 1, 2005

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

By P Waters, S Miller

BHPBilliton operates the Mt Whaleback Mine located in the semi-arid Pilbara Region of Western Australia. Approximately 200 Mt of net acid generating (NAG) material still remains to be mined. Acid Rock Drainage (ARD) was first identified at the site in 1995 following cyclonic storms. This resulted in the development of strategies that have allowed the mine to successfully manage ARD whilst continuing to operate. BHPBilliton Iron Ore is working toward prevention of ARD in its operations, however, historical practices have left residual areas that must be considered. Three significant sources of ARD have been identified that must be managed: stormwater run-off from exposed pyritic shales in pit surfaces; basal flows beneath overburden storage areas following rainfall events; and contaminated water from pit dewatering. The mine contains all ARD water onsite. This is achieved by: storage of all affected water in the ARD dam; evaporation of affected water from the ARD dam and the adjacent evaporation ponds; pumping from upstream dams to prevent stormwater from being affected; and emergency storage and treatment in-pit as a contingency. The site ARD management strategy is approved by senior management and endorsed by State Government regulatory authorities and relevant external stakeholders. Additional strategies are also under evaluation to effect long-term closure of the operation. Record rainfalls from 1998 - 2001 have tested the capabilities of the ARD strategy and management plan. Learnings from these events, coupled with recommendations from an extensive technical audit in 2000, have been incorporated into the strategy for ARD management. This paper presents the strategy and an overview of the ARD management plan that can be considered and applied by other affected sites in the management of ARD.

Jan 1, 2003

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

The last decade of national water reform implementation has improved the availability and efficiency of water source allocation in Western Australia. However, it is critical to recognise that the concurrent mining boom witnessed the approach of full water allocation limits, and increasing trends in mineral processing, water infrastructure costs, and wastewater management costs. Water supplies are commonly viewed as absolutely critical to project feasibility in mining, industrial and energy generation projects, even if considered 'non-core business'.   An increasing density of mining projects and industrial estates in Western Australia (WA) creates an opportunity for water infrastructure cost sharing and synergies. The WA government and its agencies have given preliminary consideration to the establishment of independent water utilities in the goldfields (Kalgoorlie), the Pilbara, and Collie regions, and in the Kwinana Industrial Area. The impending Oakajee industrial area and Mid West regional development, and Anketell port in the East Pilbara, could also be considered for common non-municipal water supplies.   The critical issue of apparent commercial risk due to the large scale of water demands and the low customer numbers in the minerals sector relative to other water markets is expected to mandate government partnership in any non-municipal water utility ownership. The commercial feasibility risk is observed as a risk to water supply security for potential mining and industrial customers. Absence of proper water infrastructure planning and governance has the potential to create infrastructure access issues as observed for Pilbara rail developments under the Trade Practices Act 1974.   Other aspects of water cycle management which could be addressed by a non-municipal utility include resumption of mine dewatering water (required changes to WA legislation that are progressing) and consolidated wastewater management for maximising synergy or reuse opportunities and minimising cumulative environmental impacts.   Address of water infrastructure planning for non-municipal water demands must cover commercial and environmental sustainability outcomes to successfully progress minerals sector growth in the State.

Jun 1, 2010

As a basis for my address to you tonight I thought it might be opportune if we considered the great history of the mineral industry in Australia, and the contribution it has made to the development of the country. While it is perhaps interesting to review the achievements of the past there is also the opportunity to examine the developments of the future.The names generally given to the three periods of man's life on the earth-the Stone, the Bronze, and the Iron Ageand to which should perhaps now be added the Atomic Age, imply the vast importance of the progressive steps in 'man's discovery of minerals and the means of working them. They tell the story of his advance from the flint knife to the bronze celt, and then to the keen-edged iron weapon, and now to the possibilities of the peaceful application of atomic energy. Not only have the stories of gold, iron, copper and tin told a great deal of the history of the progress of mankind, but they have also traced the commercial and industrial growth of Australia over the last century.Gold in the 1850's was responsible for the most significant period of immigration Australia has ever had-when the population almost tripled in the ten years to 1860. Minerals were also responsible for opening up Australia and determining the pattern of settlement. As mineral finds were made, railways were constructed to these fields, then agricultural development followed.Then, as the industrial era started, minerals provided the raw material for Australia's rapid industrial expansion, and they have all contributed to the extent that they have made...

Jan 1, 1960

By N Robson, E Stephens

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: political û expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and legal û mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: early identification of risks û detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, make use of companies that can help identify risks and suggest solutions, control the cost of financing û risk margin applied to a project finance loan will be influenced by the risks faced, and risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

By P S. R Reddy, V N. Misra

The iron ore deposits in India are rich in iron content but usually contains high alumina and silica. The current industrial practice results three products namely lump, fines and slimes. The lump and fines with or without beneficiation are directly fed to the blast furnace and sintering plant respectively while the super fines or slimes are presently discarded as tailings. Around eight million tonnes of iron ore slimes estimated as being 15 - 20 per cent by weight of run of mine ore containing ~48 - 62 per cent Fe, is discarded every year causing huge loss to the Indian iron ore industry. In addition, these slimes stored in massive tailing ponds pose enormous environmental and ecological problems. Extensive investigations have been carried out on three iron ore slimes generated at Barsua, Bolani and Meghahatuburu iron ore mines of India. The studies include physical, chemical, mineralogical characterisation and beneficiation studies adopting conventional hydroclyclone and wet high intensity magnetic separator. The characterisation studies have indicated that most of the gangue minerals are accumulated in finer fractions. The studies on hydrocyclone and magnetic separation had indicated that an iron concentrate of 61 - 65 per cent Fe could be obtained by recovering 59 - 78 per cent of the iron values present in the slimes. Depending on the nature of the slimes the alumina and silica levels have been brought down to 2.5 and 1.0 per cent respectively. The effects of different operating and design variables along with detailed characterisation studies have been highlighted.

Jan 1, 2002

This paper provides a brief fundamental insight regarding the fabric media concept for liquor filtration. The subject matter will be of interest to metallurgists and engineers with professional responsibility for world class design of solid liquid separation processes and efficient lowest cost operation of existing mineral process plant. Avocet Mining commissioned the worldÆs first mineral liquor clarification process incorporating a fabric media liquor filter at their Lanut gold mine in Sulawesi, in 2004 with design consulting provided by the Australian company SLS Technology Pty Ltd. Development of the technology continues with applied research focused on selecting textile parameters to apply filtration to a wider range of particle and contaminant types, higher solids concentrations, and different process liquors. Liquor filtration with the Fabric Media technology offers an array of attractive benefits. For Avocet Mining, filtration of pregnant liquor directly from the heap leach pad has enabled removal of the sediment pond and sand filters from the traditional process flow sheet, thus providing significant cost and installation time savings. Avocet Mining has recently expressed confidence in the technology indicating selection preference of the technology for the expansion at Lanut and for a new project. The application design window for the Fabric Media concept is extremely flexible with the technology now successfully applied to many different liquor chemistries and application objectives around the world. Potential cost savings for solid liquid separation process plant, such as counter current decantation circuits, clarifier vessels and thickener tanks can be calculated from laboratory measurements or pilot plant demonstrations.

Jan 1, 2008

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By P Scott

Kaltim Prima Coal, an open cut coal mine located in Sangatta, East Kalimantan, Indonesia, operates two deep pits and two shallow pits with a truck and shovel operation. KPC produced 17 Mt of coal in 2002 by removing 120 Mbcm overburden. Geochemical investigations have indicated 20 per cent of total waste rock is potentially acid forming; ie it has the potential to create acid mine drainage (AMD). In the early years of the KPC operation, the presence of AMD had been observed in the mined out areas and in the waste rock dumps as a result of sulfidic waste rock exposure. A strategy for management of AMD from waste rock was implemented involving: sampling, analysis, modelling, selective handling and validation of final dump covers. Samples of the waste rock lithologies are collected from exploration drill holes for geochemical analysis to determine their acid generating potential. The geochemical database is used to develop the waste rock model for the life of mine pit areas. The acid forming and non-acid forming waste rock is delineated for each mining bench area for selective handling and placement within the waste rock dump during the operational stage. Each mining bench is sampled and assessed to validate the model predictions. The final dump cover is sampled to meet strict Quality Assurance requirements to ensure non-acid forming waste material is used in the outer cover of the dump. The geochemical investigation of the waste rock is integrated with mine planning to design and construct the waste rock dump to minimise the risk of generating acid. This process links the exploration stage, operation stage, and rehabilitation stage for each Pit area. The paper briefly reports the waste rock characterisation, waste modelling and strategies used for management of acid drainage by KPC.

Jan 1, 2003