Search Documents

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

By M Reisi, H Waterer, M Savelsbergh, F Engineer

The Hunter Valley Coal Chain Coordinator (HVCCC) Limited is the primary planning organisation responsible for the export of coal through the Port of Newcastle, Australia. HVCCC stakeholders include producers (mining companies), rail track owners, above rail operators, and terminal operators. The HVCCC is tasked with coordinating the activities of all the corresponding parts of the coal export supply chain so as to maximise the system efficiency. The HVCCC also has a forward looking planning role: with demand for coal expected to double in the next decade, strategic capacity planning is a core activity for the HVCCC. Optimisation and simulation models are key aids in such activity. They are used to suggest and evaluate infrastructure expansions and operating policy changes. These models require input data in the form of shipping stems, which are arrival streams of ships at the port, together with their cargo types and composition, and date and time of arrival.Although everyone is familiar with the expression ægarbage in equals garbage outÆ, relatively little research is dedicated to the issues surrounding input data generation. In this research we seek to redress this, and have developed a method for generating high quality shipping data. Shipping stems used as input should be realistic, reflecting key characteristics of historical patterns. They should accurately represent future demand scenarios. Yet they should also have controllable parameters that can be used to test what-if scenarios, such as are required by the HVCCC to answer questions about future infrastructure or operational plans.Here we review our process for achieving this, and give a case study analysing the effects of different shipping stems on the performance of the coal chain, as measured by a capacity assessment tool. The latter is an optimisation model that takes shipping stem and infrastructure data as input, and calculates key supply chain performance metrics. The potential benefits of alternative demand management strategies are analysed by measuring the performance of the coal chain given different shipping stems obtained via the stem generatorÆs controllable parameters.

Sep 26, 2011

The past decade has seen a great increase in activity in deep seismic reflection profiling of the continental crust. Some 20 countries have conducted field experiments and the total length of deep seismic profiles surveyed to date is approximately 25,000 km. This total is very large compared to the quantity of such data that existed previously, but very small compared to the total length of seis- mic profiles of the shallow crust carried out for petroleum exploration, which some- times has exceeded 600,000 km on land in one year alone and 1,600,000 km/yr on land and sea. Furthermore, 25,000 km of seismic pro- filing corresponds to exploration of only a tiny fraction of the total volume of the entire continental crust. Thus at this stage of development of the subject, one must be wary of generalizations that are based on these limited data and then ex- tended in scope to include the crust everywhere. The state of the subject is such that virtually every new seismic line reveals totally unexpected seismic fea- tures, a sign that the subject is in its major discovery phase and a warning to the generalizers. Nevertheless, in addition to much new information on deep crustal structure in specific locations, some broad consequences of application of this powerful geophysical technique to a region of the earth not pre- viously explored in this manner are be- coming clear. One is that, as seismic data on the deep continental crust become more abundant and more revealing of complexi- ties, the deep crust can be far better re- lated to rocks at the surface. Conse- quently, the geological style of reason- ing is now being extended from its normal domain of the near-surface to include the deepest crust in a comprehensive story of the evolution of the continents. This change is a subtle but important one and is evident, for example, in some cross sec- tions of the North American Transect Pro- gram, which show surface geology extended in a consistent, though speculative, manner to the top of the mantle. In other words,

Jan 1, 1987

THE MORWELL BROWN COAL DEPOSITSTHIS deposits of brown coal in the neighbourhood of Morwell, are of tertiary age, and are represented on several horizons, but, owing to lack of evidence, the exact age cannot be fixed definitely. It is chiefly by reference to the basalt flows of the Older Volcanic series that the brown coal beds have been classified as of Pre-Volcanic and of Post-Volcanic age. The Pre-Volcanic brown coals are less widely distributed, and the seams generally are thin, though near Thorpdale a thickness of 40 tt. has been recorded, and from 10 ft. to 12 ft. in the vicinity of Narracan. Both of these localities lie to the south-west of Yallourn, and it has not been proven as yet whether these older coals and accompanying basaltic flows pass under the Morwell beds.The brown coal deposits have accumulated in an area where extensive faulting in early tertiary times has taken place with oscillations of elevation and depression of the land surface. In the vicinity of Yallourn, Paheozoic strata (probably Silurian) are exposed on either bank of the Latrobe River about a mile above the powerhouse weir, where the river flows through steep banks rising a couple of hundred feet on either side. The Silurian strata are highly inclined, and consist mostly of slates and Illudstones. Resting unconformably on the upturned edges of the Silurian is a conglomerate bed of Mesozoic age, above which occur beds clipping to the south-east of felspathic sandstones, with alternating mudstones at times carbonaceous, and containing thin seams of black coal.The brown coal seams and associated lignitic Clays, sands, gravels, etc, rest on the Mesozoic strata (as proved in the vicinity of the power-house and by boring north of the Latrobe River, near the old open cut), but do not appear on the surface of the Mesozoic, where these beds attain an altitude of more than 50 ft. above the present level of the Latrobe River.Half a mile upstream from the power-house a layer of basalt of the Older Volcanic series, almost resting upon the Silurian strata, is...

Jan 1, 1924

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By D Monaghan

Pumping water for dewatering and water supply is a major component of electricity consumption at mining operations and hence is a significant contributor of greenhouse gas emissions. Pump systems at a typical mine site can be broadly split between above ground centrifugal pumps (generally used for water transfer) and submersible borehole pumps (generally for dewatering and/or water supply). In contrast to above ground pumps, submersible borehole pumps can be subjected to varying duty points (total pumping head and flow requirements) as a result of changing bore water levels and yields, particularly in mine dewatering bores. Typically, much higher pumping rates are required at the commencement of dewatering to remove groundwater storage and to intercept sufficient groundwater throughflow to achieve target drawdowns. Once target drawdown levels are reached it often only requires much lower pumping rates to maintain target drawdowns. Pumps sized to remove the large initial volumes of stored groundwater often end up too large for the lower flow rate required for æmaintenance pumpingÆ. This often results in pumps operating inefficiently, a problem which can be made worse when pumps are throttled to reduce the pump output to better match the reduced bore yield. Current standard operating practice places little emphasis on the electricity consumed by pumps, with the focus often being on minimising capital expenditure (æIf it ainÆt broke donÆt fix itÆ). Submersible pumps can have extended service lives of ten to 20+ years. However as the capital cost of a pump typically represents only five per cent of the life cycle cost, the vast majority of the life cycle cost is energy usage.Through the implementation of a regular review of the operation of borehole pumps, significant reductions in electricity use and associated greenhouse gas emissions can be achieved without impacting the dewatering schedule. In most cases, the capital cost of replacing pumps is more than offset by savings in operating costs. These potential savings become even more significant when considering proposed future carbon tax levees.This paper presents examples of the opportunities for significant reductions in energy, greenhouse gas emissions and overall costs that can be achieved for a range of dewatering scenarios.

Jan 1, 2009

By J Barnes

During September 2000, Nabalco management identified the need for a corporate system to deliver its key performance indicators (KPIs). In June 2001, a need was also identified to replace the existing metallurgical accounting system. After a review of the technologies available, the decision was made to develop the systems in-house, in preference to purchasing commercial software packages. This would allow much greater control over the structure, and provide for an iterative, concurrent development process between software and key business developers. This has proven invaluable in the development process. The purpose of the KPI system is to provide a unified reporting tool for all performance indicators. These indicators include production, safety, health and environment, personnel, costs, continuous improvement initiatives and opportunity losses. All of these disparate measurements are brought together into the KPI system and used to determine the performance for each department or area. The general principles of the balanced scorecard business approach (Kaplan and Norton, 1996) are applied to achieve a performance measurement for each area within Nabalco. The new metallurgical accounting system (MA) is a SQLServer database with web page and Excel interfaces. The database is structured around daily inputs of all measurements and calculations. The data is stored and adjustments and reconciliations can be made to this data as required. The focus is on accounting rigour, with all adjustments recorded in the database to allow for full auditing. The structure of the data focuses on the five input/output streams (bauxite in, caustic soda in, fuel oil in, residue out, and alumina out). In-circuit inventory provides a secondary measurement on which to check and calibrate the MA system. The KPI and MA systems were developed using Web technologies and are available to any internet-enabled device with Internet Explorer installed. This removes the need for software rollouts and user training. This will promote the wide use of the systems throughout Nabalco and Alcan.

Jan 1, 2002

A metallurgical balance drawn around a mineral processing plant or smelter must involve all process streams crossing the plant boundary. Modern sampling theory, as formulated by Gy, and sound statistical method can be used to determine the uncertainties in the observed assays for the set of balance analytes and in the mass flow rates of the process streams for the balance period. These uncertainties can then be used together with the material balance equations to arrive at adjusted component mass flows that satisfy the material balances exactly. To determine whether or not the data is consistent with the level of uncertainty in the data and with the material balance equations, a goodness of fit test is applied. This goodness of fit criterion is the principal tool to quantify the quality of the material balances. The mathematical structure of the statistical material balance problem poses a number of challenges. For example, while the variances of the adjusted component mass flows do not vanish, the variances of the sums of the adjusted component mass flows about each balance node do vanish, simply because the balancing computation demands that the balances close exactly. Even though it can be shown that the variances of the adjusted component mass flows are always lower than the estimates for the corresponding unadjusted component flows, it is still not possible to construct a confidence interval on the component mass flow into (and out of) a balance node using the adjusted component flows. On the face of it, such a confidence interval is exactly what is most desired from the balance calculations. The problem arises because the balance problem is a data adjustment rather than a parameter estimation problem. It is possible, however, to calculate the recovery of a component to a product stream and determine a confidence interval for the recovery value. It is also possible to calculate an uncertainty in the mass flow of any balance species in any process stream, before and after balancing.

Jan 1, 2005

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

Using a Jarrell-Ash "Compact" direct reading spectrometer, analyses were made of a wide variety of rocks ranging from acidic to ultrabasic types. Statistical evaluation suggests that accuracies comparable with the values obtained by the rapid chemical methods used by the United States Geological Survey will be obtained.The spectrographic method involves fusion of the rock with lithium tetraborate, strontium being incorporated in the flux as the internal standard. The resulting bead is ground with graphite and pressed into a pellet. The counts obtained on two standard pellets are used to correct for instrumental drift.Background readings are made at 4109 Å and corrections for background are made to all lines. Corrections for matrix interferences, both by chemical suppression and optical enhancement, are made. The three corrections of drift, background, and matrix are incorporated into one general expression which has been programmed on magnetic cards, each element requiring a separate card. The cards are placed individually into a desk top computer (an Olivetti Programma 101), which enables true counts to be calculated from the "readout" counts, and the element concentration is then obtained from computer-printed tables by referring to the appropriate value of true counts versus concentration. These tables were prepared by making a polynomial regression analysis of the spectrographic results from 50 standard and analysed samples, a curve of best fit being chosen for each element.The regression coefficients, usually of a fourth or fifth degree equation, together with other relevant data, were fed into a large computer, programmed to print out tables of concentration versus true counts. This technique enables the results obtained to be based on mathematically-derived values rather than on hand-drawn calibration graphs, giving greater inherent accuracy. The technique has been shown to give results of good accuracy and acceptable precision suitable for many geological and geochemical exploration programmes involving the analysis of many rock samples of different types.

Jan 1, 1969

By R Lloyd

Coal Services (Health and Safety Trust) funded ARRB Transport Research Ltd to investigate fatigue and performance of truck drivers over consecutive shifts. The main questions were to assess: What is the most important contributor to acute fatigue in mining? Is it length of shift (eg eight hours versus 12 hours) or is it time of day (eg circadian effects)? What is the limit of successive day or night shifts before chronic fatigue affects operator performance in open cut mines? The project methodology included utilising ARRB Fatigue Monitoring Devices (forced-choice stimulus reaction) in eight haul trucks, testing 24 subjects over several weeks. Each subject filled in a Fatigue Risk Questionnaire on lifestyle and health. Operators worked a 14-night, one day off, 13-day roster of 12-hour shifts in a fly-in/fly-out operation with excellent opportunities for restorative sleep between shifts. A total of 3500 hours of real-time data was collected, representing the first set of objective, real-time driver performance data for Australian mining. The data showed that for a single night of driving haul trucks, there appears to be no effect on operator fatigue from the amount of time on task (for the 12 hours). In fact performance was worse through the first eight hours than the last four. The circadian influence had a stronger affect than working more than eight hours. Of the 14 nights worked at the site, nights 13, 14, seven and two respectively, were the worst. This presents a conundrum for policy makers who may like to place caps on working hours or rosters in the hope that it will alleviate the fatigue issue. It will not. The major finding within this study is the combined influence of circadian rhythms (human body clock) and individual variability on performance. The lifestyle habits and the health of individuals have a profound effect on operator performance as shown by the strong positive correlation between high fatigue risk scores from the Fatigue Risk Questionnaire and poor performance. An individualistic approach would appear to have the best chance of reducing high potential incidents due to fatigue through successive nightshifts.

Jan 1, 2005

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By N Green

The production of approximately 550 000 tonnes of æwhiteÆ or chrysotile asbestos fibre between 1972 and 1983 at the Woodsreef Mine in New South Wales left behind 24 million tonnes of tailings and 75 million tonnes of waste rock and overburden. The Woodsreef Magnesium Project is designed to extract the 23 per cent magnesium content of the tailings to produce magnesium metal and magnesium alloys, the latter with aluminium from the New South Wales smelters. Further value will be added to the tailings waste with the downstream production of magnesium alloy sheets and cast products for the transportation, electronics and other consumer goods industries. The mine opened in 1918 and closed in 1983 becoming derelict. There has been minimal expenditure on rehabilitation compared with that recommended in reports commissioned by the New South Wales Government. The tailings dump has been designated æasbestos wasteÆ by the EPA and will be eliminated through the magnesium refinery process of the Project with the dissolution of the remaining chrysotile fibres. The benign waste from the refinery process will consist principally of silica with some iron. Significant energy savings are expected from innovative new processing technology, in the alloy formation and in the application of the light weight, cast and sheet metal products, particularly in the transportation industries. Globally, there are very large resources of similar tailings with hundreds of years of useful productive lives that could be converted into the metal of the 21st Century, magnesium, and its alloys, to assist pollution and greenhouse gas reduction from transportation industries. No new mining and minimal feedstock preparation is required. Unlike potential producers using carbonate rocks such as magnesite and dolomite that have to be mined, the asbestos tailings composed principally of non-fibrous serpentinite do not contain any carbon dioxide.

Jan 1, 2002

The mining industry was one of the first to be directly regulated by legislation in the 19th century when British public opinion was mobilised by reformers seeking social change. In the next wave of mining safety legislation, account was taken of technological advances in the industry, but again, the amendments were in large measure driven by public expectations following a series of disastrous mining accidents with great loss of life. The result was the prescriptive and detailed type of regulation that has, to a great extent, remained with and become a way of life in the mining industry of today. In 1970, the then British Government appointed Lord Robens, a former Chairman of the National Coal Board, to head a Committee of Inquiry to consider the arrangements then in place for preserving the safety and health of people at work and to consider and make recommendations on the need for change in the legislation governing such matters. The result was the 1972 report Safety and Health at Work which, in turn, resulted in the Health and Safety at Work etc Act 1974 (UK). This Act, which embodied the now familiar concepts of consultation with the workforce on matters relating to health and safety and the statutory application of the previously existing Common Law concept of the duty of care, became the model for much occupational health and safety legislation in many places around the world, including the various States of Australia. As a result of the `Robens style' of legislation, the regulators of the mining industry have had the opportunity to become less prescriptive and to introduce an `enabling' style in their statutes. This has not always been welcomed by the industry which has, to some extent, missed the comfort of knowing exactly what is required of it in order to ensure compliance with the legislation while appreciating the `self-regulatory' opportunities that the new style of regulation offered.

Jan 1, 1995

Many operating hard-rock sulfide mines are predicted to require perpetual post-closure management to prevent environmental degradation. Causes include evaporative concentration of metals and other solutes in pit lakes, and acid rock drainage from sulfide waste-rock, tailings, and pit benches. Dilemmas posed by the prospect of perpetual management include: uncertainty in predictive models typically prevents reliable bounding on forecasts for the timing or magnitude of environmental impacts; comprehensive closure designs that can meet environmental standards may not be economically possible, particularly when applied retroactively to mines permitted under less stringent closure requirements; the publication of site-specific environmental analyses in peer-reviewed journals are discouraged in the current regulatory environment, hindering scientific advancement; and the durability of financial and government institutions cannot be assured for the long-time horizons over which mine impacts are predicted to occur. Re-evaluating mine closure in a framework of sustainable development (as proposed by the Mining Mineral Sustainable Development forum), can resolve, in part, these dilemmas. Key sustainability goals include: assurance of the social and economic well-being of the local community; assurance of the long-term environmental integrity of the region; and establishment of institutions capable of addressing (and learning from) long-term environmental management. Under a sustainability framework, impractical plans for immediate attainment of perpetually-stable closure may be replaced with a fund for long-term management of environmental impacts (eg through contaminant migration controls and exposure barriers), and a set-aside long-term growth reserve intended to eventually fund more complete closure. Fund expenditures would follow Adaptive Managementùa template for environmental-management institutions in which knowledge accumulated and uncertainty acknowledged explicitly. Under adaptive management, trusts would be flexible entities, supporting an evolving program of monitoring, predictive model refinement, and treatment. Periodic value of information analyses would target data collection efforts, refining the balance between predictable cost and uncertainty. This framework could overcome present-day financial shortcomings, enhance the field of environmental science, and meet the needs of future generations through the propagation of capita.

Jan 1, 2003

By N Slade, D Kennedy

Optimal throughput is a key objective for the successful operation of any manufacturing or processing business. In the mining industry in particular, in order to obtain maximum return on the significant capital investment in the physical assets involved, ensuring continuous throughput is a major focus for the complete leadership team. Failure to meet throughput objectives becomes a major source of distraction for management which too often attempts to solve shortfalls by æforcingÆ and æenforcingÆ production targets. This focus on the short term and the lack of attention to addressing root causes frustrates operators who attempt to satisfy unattainable short-term targets and lose sight of the long-term goal. Mount Isa Copper Operations, Xstrata Copper, North Queensland, had ambitious plans to increase throughput volume by ten per cent within a four month period to allow budgets to be achieved within the financial year. To achieve this, the process had to overcome the interplay of a multi-node (æsiloedÆ) production system and its associated inventories, each node, of which on the face of it at least, had more than enough ænameplateÆ capacity to meet these plans. However, the actual volume achieved at the end point of the system was well below this nameplate capacity and the system operated with an extraordinarily high standard deviation. The key issues in terms of making or exceeding plan were: how to substantially reduce the variability of the system and managing the inventories between nodes, how to synchronise throughput between the production nodes, and how to improve the decision-making ability within the process. In this paper, the implementation team has shown that a revolutionary process view of the operation together with appropriate planning decisions allowed increased throughput to be achieved without further capital investment.

Jan 1, 2006

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

By D A. Williams

The conventional method of transporting mine tailings from a process plant to a tailings storage facility (TSF) is in the form of a low to medium density1 slurry, which can be pumped using centrifugal pumps. Over the past several decades, therefore, mine operators have generally adopted this default approach. There are, however, some convincing arguments why consideration should be given to thickening the tailings slurry to a higher density paste consistency. In particular, the minimisation of environmental impacts, the reduction in water consumption and the cost savings relating to TSF closure make paste an attractive option for the life of mine tailings disposal. There are several environmental impacts that are associated with a conventional slurry TSF, such as land sterilisation, aesthetics, dust, seepage and acid mine drainage. Some of these impacts, such as dusting, may be difficult to mitigate while the TSF is in operation. Others can be influenced by adjustments made to the tailings slurry density at the plant. Unplanned fluctuations in slurry density and/or viscosity can have a significant influence on TSF performance and can exacerbate the environmental impacts relating to the facility. Relatively minor changes in the solids content of the slurry can affect tailings beaching behaviour, degree of segregation, position of the phreatic surface, amount of freeboard, consolidation behaviour, placed (settled) density (and hence TSF capacity) and in situ strength of the tailings. Paste is a non segregating slurry and many of these effects can be minimised at the TSF when the tailings slurry is thickened to a paste. These improvements are manifested by reduced seepage, flexibility in selecting an appropriate final landform, ability to rehabilitate progressively and reductions in plant water usage. It is possible to minimise environmental impacts of a TSF through the use of tailings paste. Ideally the paste production plant should be part of the initial design of the process plant. However, significant benefits can be gained by adding a paste production plant at some time later in the operational life of the mine to reduce environmental impacts and facilitate an environmentally acceptable TSF closure.

Jan 1, 2002

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923