Search Documents

This paper reports on the field results of using electronic detonators to improve blast outcomes. OricaÆs electronic detonator, the i-konTM Digital Energy Control System, allows exact and precise timing in 1 ms increments from 0 to 15 000 ms. This gives the blast engineer and shotfirer the ability to fire a blast using any possible desired sequence. In the three years that have followed the release of the i-konTM System, Orica has been re-exploring ways of initiating blasts using the abilities of electronic detonators to improve fragmentation, diggability and crusher throughput. This study began with revisiting fundamental blast theory, lead to generation of new state of the art computer fragmentation modelling and ended with many iterative field trials of i-konTM blasts across a wide selection of mining methods and rock types. At three sites a detailed measurement process was undertaken to compare the results of pyrotechnic blasts with i-konTM blasts. This paper will detail the significant improvements in fragmentation, diggability and crusher throughput that was found at these sites.

Jan 1, 2003

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987

IN the course of his employment the Broken Hill Co. the writer has had occasion to use and instruct others in the use of the Shamrock rescue apparatus. This paper deals with the various types of apparatus tested. The common object of the various types of breathing apparatus is to enable the wearer to remain and work for varying periods of time in an atmosphere which is either deficient in oxygen or is poisonous that is, contains carbon monoxide or irritating and irrespirable vapours, such as the smoke from underground fires, sulphur dioxide or ammonia fumes. For any apparatus to be efficient as required in the above paragraph it must fulfil the following conditions;1. Air-tight as regards the passage of the air from the outside to the inside. In atmosphere containing carbon dioxide a slight leak would not render the apparatus useless; but where irritating vapours, such as the smoke from burning oregon and sulphides, are met with, even the slightest leak must be avoided.2. The oxygen supply must be ample, and so supplied that it is not checked by expiration.3. Expiration and inspiration must not be retarded.

Jan 1, 1911

By R P. Langford, T A. Moore

Over the last 15 years Indonesia has experienced a surge in coalexploration, which has led to the development of a major export industry. This coal exploration has improved the understanding of the geology of the Indonesian coal deposits. The main economic coal deposits are of Eocene and Miocene to Pliocene age, which mainly occur in Kalimantan and Sumatra and were formed from peat deposits in an equatorial paleoclimate similar to that prevailing today. Some of these peats were domed peats, which grew above the normal water tables, under a climate of year-round rainfall; these peats grew above the level at which waterborne mineral matter can enter the system, resulting in low ash and sulphur, and locally very thick coal. It is believed that such peats have formed the unusually thick, low ash, and low sulphur Miocene coals of Indonesia. Coal deposits of Eocene age are typically characterised by thinner seams, with relatively higher contents of ash and sulphur. The Miocene coals and Eocene coals both appear to have formed in lacustrine, coastal plain or deltaic depositional environments, similar to the modern peat-forming environments of eastern Sumatra and parts of Kalimantan. The Eocene coals formed mainly in extensional tectonic settings. Miocene - Pliocene coal deposits formed in a range of tectonic settings.

Jan 1, 1999

By Ritchie I

Copper minerals are often associated with gold ores. These create processing problems since cyanide solutions are not selective for gold alone. Copper minerals are also leached by cyanide, and typically each one per cent of `reactive' copper in the ore consumes about 30 kg t 1 cyanide. Once in solution, copper cyanide species create further processing problems as they adsorb onto carbon along with the dicyanoaurate ion. These problems make conventional cyanidation of gold ore uneconomic if the ore contains too much copper. As a result, methods of economically processing gold-copper ores are becoming of increasing importance.One of the more promising methods of treating these ores is by selective leaching of the gold by an ammoniacal cyanide solution, a method first described by Hunt in 1901. This method is already in commercial use in Mauritania, treating copper/gold tailings. In general terms, the addition of I - 2 g U1 ammonia to a standard cyanide leach solution causes a significant increase in gold extraction and decrease in copper extraction. However, early testwork on this system has concluded that the optimal leach conditions are critically dependent on ore composition, and the mechanism is not well understood, making predictions of best conditions impossible.

Jan 1, 1997

Chief Geologist, Groundwater and Engineering Geology Branch South Australian Department of Mines and Energy The six papers submitted for consideration during this session include two dealing with techniques for measing rock mass behaviour, including permeability, in boreholes, one describing the use of surface geophysical methods to delineate pollution plumes in groundwater together with analytical modelling of the plume, and one presenting a biological tracer technique applied to the determination of the origin of water entering underground mine workings. A paper describing dewatering at a base metal mine in Queensland includes an account of the investigation techniques employed to establish a conceptual model as a basis for the evaluation of various dewatering strategies. Of considerable interest is the use of a field gravity survey to delineate a zone of highly weathered rock which forms the major aquifer at the site.

Jan 1, 1988

Bulk mining and handling technologies have been affected in two ways by the soaring costs of oil products in recent years. Firstly, the substition of oil by coal, oil sands and oil shale demands the development of high-capacity mining and handling equipment, and secondly the rising fuel costs favour a trend away from cost-intensive heavy truck transport. To cope with the growing volumes of material in mining and handling, larger equip- ment units have to be designed. This tendency becomes apparent from the examples of the Hambach open pit mine in Germany, and the Port Kembla handling plant in Australia. A combination of the flexibility of heavy truck transport and the cost advantages of belt conveyors is achieved by the system of semi-mobile crushing installations described in this paper.

Jan 1, 1981

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

The latent conditions clause in various general conditions of contract have traditionally proved to be a source of significant disputes in tunnelling contracts, even when extensive geotechnical investigations have been carried out at the tunnel site and a report of these investigations provided with the tender documents, informing the contractor of the nature and extent of subsurface conditions likely to be met with during execution of the works. This paper discusses the contractual aspects of the new latent conditions clause in the recent Australian Standard AS 2124-1986, General Conditions of Contract, in relation to tunnelling contracts. A comparison of this new clause is made with other latent conditions clauses in general conditions of contract in use in Australia and other commonwealth countries. It is seen that the new latent conditions clause in the recent Australian Standard 2124-1986 has, by providing for a reasonable apportionment of risks, attempted to minimize contractual disputes relating to latent conditions in tunnelling contracts and to provide a satisfactory basis for quick and efficient settlement of such disputes should they arise during execution of these contracts.

Jan 1, 1987

Coal mining in the Illawarra commenced in 1848. By the early twentieth century mining operations were spread over quite a distance along the coast centred on Wollongong. By this time there were already numerous tunnel mines and one shaft mine. Coal was first reported in Illawarra by Lieutenant Flinders on a voyage of exploration, southerly along the coast from Sydney in 1796. Because of the topography, particularly the escarpment and the narrowness of the coastal plain, access from Sydney was not easy by land and the normal access was by sea. It was not until some coastal areas had been developed for agricultural purposes that the mining of the seams on the South Coast commenced for the supp- ly of fuel. The most important mines in the early nineteenth century were Bulli and Osborne Wallsend. In general, coal was won from the tunnel mines and was transported directly, usually by tramway, to the nearest shipping point. Considerable hardship attended the earliest attempts at mining coal in regard to materials for mining and the way of life of the miners in the vicinity of the mines. With the growth of production and the installation of coke ovens at some mines the area, hitherto virgin bush- land, began to take on a more industrialised appearance. The mines were necessarily small,

Jan 1, 1976

The purposes of defining the mining environment for underground mass mining and the uses of characterisation data are outlined. The requirements for data in the areas of geology, surface and groundwater hydrology, topography and environmental constraints and geotechnical studies are identified. Emphasis is then placed on the collection and interpretation of geotechnical data for establishing the in situ stress regime and for rock mass characterisation. Methods used for diamond drilling, core logging, borehole logging, data analysis and presentation, rock mass modelling and rock mass classification are outlined. Finally, recent and potential advances in the state-of-the-art are identified in areas such as geophysical methods, measurement while drilling, computerised data collection and analysis, rock mass modelling, in situ stress measurement data presentation and interpretation, and some applications of rock mass characterisation data.

Jan 1, 2000

Hindustan Zinc Limited has successfully installed an In-Stream Analysis and Process Control System in the flotation section of the Balaria Lead-Zinc concentrator at Zawar Mines. The system comprises In-Stream Analysis to continuously monitor lead and zinc levels in feed, concentrates and tailings streams, field instrumentation for reagent distribution and flotation cell level control linked to a central Distributed Control System for supervisory control functions. An intensive training scheme was conducted by the system supplier for concentrator metallurgical and instrumentation engineers. Since commissioning of the system in April 1989, Hindustan Zinc has enjoyed the benefits of improved lead, zinc and silver recoveries, improved concentrate grade control and reduced reagent costs.

Jan 1, 1991

By I Kolomaznik

Each technological process can be reduced on the transport networks, and namely on the parametric networks and the non-parametric ones. The parametric networks are created by the piping, electrical cables or channels. The non-parametric network is created by the ways, suspended grooves, trackages and also by the belt conveyors or other conveyors for continuous material transport. If we reduce the technological process on transport networks, then, by the creation of these networks models and their mutual interconnection we obtain the model of the whole technological process. The model can be understood as the universal one, without exaggeration, because it is valid for any technological process. However, for us the mining production process is important what represents the mining and transport of raw materials under the support of the ensuring system. In this contribution one of the first attempt is described, and namely how to connect the parametric network which has been already worked out very properly with the non-parametric network what is presented in this contribution by the transport line of belt conveyors.

Jan 1, 2003

By Opitz E. A

The integration of environmental and permitting strategies into development has become a routine part of doing business for the international minerals industry. Paralleling the development schedule with the environmental and permitting schedule is critical to ensuring that design recognises environmental constraints and that the environmental and permitting program has the right focus and achieves the objective of obtaining workable permits that reflect the project design. Regulatory issues including the law of and controls established by the country the project is situated in, the requirements of international financing institutions, international politics and the role of environmental groups and the particular precedents and processes established are all important issues that must be recognised and incorporated into the permitting program by the developer. Technical issues including collecting early environmental data during exploration, establishing hydro-meteorology equipment, baseline data gathering, and getting good environmental engineering information as a part of feasibility and design are also critical issues to the success of a project which are under the direct control of the developer. Finally tying all of these issues into a single integrated strategy under the direction and control of a nominated team is necessary to maintain focus and achieve results.

Jan 1, 1997

By P Ormsby, T Hewitt

Ore in pillars constitutes a significant proportion of the ore reserve at PasmincoÆs Broken Hill Mine. Many of these pillars are narrow (5 -6 m) and high (16 û 35 m) vertical blocks. High-grade ore has been left between primary horizontal cut and fill stopes. These stopes were mined from the late-1960s until the early-1980s. Fill material is a variety of hydraulically stowed sand, sand-cement, and remnant timber support. Many pillar cut-throughs were made between the old stopes. In order to gain access for the current pillar recovery operations, it has been necessary to develop pillar drill drives through, and adjacent to, the hydraulic filled stopes. Whilst long hole recovery of vertical pillars is not new, some notable successes using innovative ideas have been achieved during 1997. These innovations include:The use of steel mesh reinforcing in shotcrete when mining through, or adjacent to, hydraulic fill. Construction of steel sets to support vent rises and haulage ways encountered in the cut-throughs. The use of ground movement monitoring equipment. Survey lasers with chain droppers and convergence monitors were installed in the 18 Pillar to detect any movement of the pillar block and decrease risk to personnel. The development of a three-dimensional computer model of primary stoping, using Vulcan software, to assist in the design of pillars. Maximisation of recovery using different drilling and firing practices.

Jan 1, 1998

By R Farana

The future challenges in mining instrumentation, mainly on future intelligent mines, are to continue providing instruments with the highest level of reliability at the lowest possible cost, and also to take advantage of technology existing in other industries and to adapt it to the mining context. New wireless instruments (smart sensors, smart actuators, smart controllers) would also be very useful, as well as instruments fully adapted to the monitoring of large movements that are observed, in both underground and open pit mines. Mining instrumentation is found to various degrees in most mines, both open pit and underground. Smart mining instruments present a certain number of aspects specific to the environment in which the instruments are installed. Namely, the instruments can be installed either for short-term or long-term purposes. The mining industry is always looking for useful instruments that can provide relevant information on ground behaviour adjacent to mining stopes or permanent infrastructure. The instruments must meet the various criteria, and must also evolve with the new mining technologies that are continuously being implemented. A strong collaboration between the mining industry, research organisations, and instrument manufacturers is the key to meeting these objectives. This contribution describes the current trends on smart sensors and smart instrumentation with Wireless LAN support.

Jan 1, 2003

By Beeforth C. G

The use of Non-Linear Programming to obtain improved schedules of future activity in two specific cases of mining and treatment of minerals is described. The two cases were (i) reclamation of gold, uranium and sulphur from old surface tailings dams and, (ii) underground mining of gold. The method used an augmented Lagrangian device to reduce a constrained Non-Linear Programme to a sequence of unconstrained hill- climbing procedures. The main advantages of the method appear to be those of (a)flexibility of modelling of industrial characteristics and constraints and, (b) reasonably modest computation times.

Jan 1, 1977

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

By T Ueda an, T Sasaoka, A Yabuki, H Shimada

The basic concept of auger mining is to extract coal beyond the economic limits of surface mining technology by drilling holes of an appropriate diameter size into the exposed seam of the highwall as deep as is technically, economically and operationally feasible. This method of mining is used at the final highwall of typical surface mining operations. This paper describes the auger mining systems and discusses the methods to increase the coal recovery in auger mining from a field trial in Australia.

Jan 1, 2003