Search Documents

Traditionally trucks have dominated haulage in open pit mines. Only recently have conveyors begun to be used in the long haul and high lift duties of surface mines. Steep angle conveyors are proven versatile systems for elevating or lowering materials continuously at steep angles to 90¦. This paper describes the design of a bucket-type steep angle conveyor that was developed as a joint research project between the Western Australian School of Mines and the Maanshan Institute of Mining Research in China. The steep angle conveyor can be used as a viable option for transporting blocky ore from open pit mines. A pilot conveyor was constructed and tested to determine its technical and operational feasibility. Furthermore, a computer model based on Matlab mathematical modelling software was developed to simulate the performance of the pilot conveyor. The model enabled to determine the design parameters of industry-scale conveyors to yield satisfactory performance. These conveyors become very cost-effective for those mines having large mine lives and depths greater than about 500 metres.

Jan 1, 2003

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By Jensen B

The investigation of the explosion characteristics of nine Bowen Basin (Central Queensland) dust samples in a suitable coal dust explosion chamber using a new dust concentration probe provides several advances in the area of coal dust explosibility testing. The 20 litre explosion chamber, of novel design, uses rotation of the main body of the chamber together with air jets for dust dispersion, and allows testing of different types of explosion initiators and analysis of the explosion characteristics of coal dust/methane mixtures of varying concentrations.A new development was a dielectric dust probe for the measurement of coal dust concentration. A capacitive micrometry technique was successfully adapted to measure dust concentration. The system uses a ratio-transformer bridge for measurement of small changes in a capacitive probe designed to sample a representative volume. The device is accurate, and is capable of operating in the hostile environment within the explosion chamber.The explosion chamber and dust probe characterise the explosive potential of coal dust samples by determination of the dust lean limit concentration in varying mixture with methane. Plots of lean limit points obtained in this way present an explosion curve for each sample which indicates the potential of the coal dust/methane to explode under the conditions of initiation in the chamber. The explosion curve obtained for each sample presents a unique signature that appears to reflect the physical and chemical characteristics of the dust.The results from this series of laboratory experiments appear to provide a useful index and indicate potential areas of interest for future research.

Jan 1, 1991

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

This paper discusses the implementation and potential limitations of the method for estimating sampling and analytical errors of multiple source mine output blended into a shipping product, described by Everett and Ziegelaar (2010). The practice of quality measurement varies between iron ore miners. The common objective is to monitor effective resource utilisation and control of product quality to customers. A flow diagram is given presenting the various options used by iron ore mine operators and the merits of the different options are discussed.

Mar 1, 2010

Thank you for the opportunity to speak at this important conference attended by aspiring mining professionals, some of whom will become the leaders of the mineral resources industry that forms the solid foundation of AustraliaÆs past and that will fuel the exciting growth of AustraliaÆs future.I want to briefly touch on the history of our business, then look at the opportunities that exist in the contract mining industry and finally comment on what the educators need to consider in their curriculum to meet the needs of our business. Byrnecut started out as an idea in early-1987 developed by a group of four mining people. At the time the industry was on the high end of a mining boom, the era of the Bonds, Connels, Skases and so on. Riding on this wave of euphoria we borrowed $600 000 from the National Australia Bank and, without having enough knowledge to lose sleep over the potential risks, started business in mid-1987. The euphoria quickly evaporated with the 1987 October stock market crash. The bank pulled our overdraft, equipment finance rates increased to over 20 per cent per annum and my house was mortgagedseveral times over. The business learning curve was extreme for a young mining engineer who had developed his trade in the relatively sheltered environment of a large public mining house, namely WMC. We were somewhat bitter that the banks had done a runner. We were a private company, backing the business with personal assets with our shoulders to the wheel, whilst the Bonds of the world had theirnoses in the trough ripping off mum and dad shareholders. All of this had a sobering effect, namely keep your feet on the ground, stick to the knitting, work hard and worship cash flow. Since that stressful but adrenaline pumping beginning the company now employs over 600 people and is now working for major mining houses at over a dozen locations in Australia, east Africa and WesternEurope and the National bank is again our banker. On this basis I consider myself qualified for the subject of this speech.

Jan 1, 2002

Through the stress synthesis of many examples of macrostructure in the middle of China, it can be concluded that in the middle of Chinesetectonics there are two compression-torsion-forces, one of which ( from NW to SE ) came from the northwest side of Aerjinshan abyssal and giant fault("F1A", see Fig.7,8,9 ); the other (from S to N ) came from the south side of the north piedmontal fault of Kunlunshan-the south piedmontal fault of Qinlingshan ("F2K-F2Q", see Fig-7,829 ).Owing to the two compression torsion forces a new special type of structure named rotation-apart structure occurred from Chaidamu basin to Hebai, Henan, Anhui plain,from Caledonian movement, Hercynian movement,Yenshan movement to Himalayan movement, step by step In the north of Qilianshan during the late Caledonian movement: during the Hercynian movement it extended into a vast area including the Chaidamu basin and Eerduosi basin; during the Yenshan movement it spread over the whole area of Helanshan,Eerduosi basin and Hebai , Henan, Anhui plain. In the period of Himalayan movement all these structures revived .The rotation-apart structure controlled the distribution of all mineral deposits and also were the mineralizing structures.The relation between these rotation-apart structure and earthquakes is very close.

Jan 1, 1990

By Whittaker B. N, Reddish D. J

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

By Trudinger J. P

Concern for the environment by the public and by mining companies, has led to many recent attempts to revegetate areas disturbed by mining activities. The problem of successfully revegetating disturbed areas and mine wastes is often difficult, even under favourable conditions. Under the severe conditions that prevail in and and semi-arid parts of Australia, such difficulties may be extreme. An approach is described in which field trials are used to investigate factors which adversely affect revegetation and to evaluate optimum methods and treatments..A wide range of methods suitable for use in and situations is described. These include grading and cultivating operations, topdressing with natural soil materials, selection of suitable plant species, mulching and the use of fertilisers and supplementary irrigation. It is concluded that such a programme provides the best approach to this complex and expensive problem.

Jan 1, 1976

By He F, Zhu D

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced Normally.

Jan 1, 1992

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

By I KylmSkorpi, H Mansikkaviita

The traditional direct-heated drying process has been replaced by the steam drying process in non-ferrous metal smelters, where steam is available from waste heat boilers. Many recent projects have selected Kumera Steam Dryers in equipping a new production line or modifying an old production line. The industrial performance of the steam dryers has shown significant energy saving and emission reduction. The steam dryers have been operated at high availability and long maintenance interval. As the process principle of Kumera Steam Dryer is different from other equipment, the set-up for steam dryer plants is configured to fit the smelter site and operation conditions to achieve optimal performance. This article discusses the equipment involved in the steam drying process and their combination options.

Jan 1, 2008

This paper will address this question from the point of view of a drill and blast engineer or researcher working in open cut and underground mining operations. The paper will establish a common set of reference standards for high-speed imaging and data capture, which engineers and researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of mining and blasting applications analysis and research. In addition, the paper will examine the different technologies from an image quality and data stream reference point, ease of operation, cost, and reliability parameters. Finally, this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of quality control, research and analysis in the mining based industries. This will include a novel approach to digital high-speed imaging and data analysis in the field, which should deliver high-quality images and data analysis in a time frame that is more appropriate to the need for immediate action, analysis and problem solving.

Jan 1, 2007

By N Meadows, M Rodriguez

A 200 000 tpa heap leach demonstration plant was approved by the Murrin Murrin Joint Venture (MMJV) in December 2005 and engineering commenced in January 2006. The demonstration plant will utilise stockpiled ore reject material (æscatsÆ) and extract nickel and cobalt. Limited production from the demonstration plant is expected by the end of 2006. The demonstration plant will enable the company to fully investigate and understand all associated technical issues over the next 12 to 18 months, including the potential to expand the heap leaching operation to a commercial scale. In parallel, the MMJV will continue a research and development program to improve and expand the application of its heap leaching technology.

Jan 1, 2006

This is the time of year tor the presidential address, and with the present incumbent engaged in the coal mining industry, it will therefore come as no surprise to you that the theme of my address this evening is concerned with coal.There are other reasons for this apart from my contact with the coal industry. At present, coal is supplying considerable overseas revenue at a time when the remainder of the mining market is in a somewhat depressed state. That times will change goes without saying, if history is to be believed.However, so far so good for coal. My first reaction when The Institute indicated its wish that I be president for 1976 was to become deeply conscious of the honour bestowed on me.On consideration, I realized that very few past presidents have been intimately connected with the coal mining industry to the extent of indulging in it for lengthy periods as a full time occupation or, conversely, a part time interest for a long time. It also appears that not one had started their career in the industry. In my case, 'also, there were 8 very interesting years ,as a gold miner and metallurgist before commencing in coal.It therefore seemed appropriate to endeavour to discover ,why this should be so, as coal mining is now a very important part of a very important industry. What were the reasons why the industry took so long to emerge when there were ample reserves of easily accessible coal?Frankie and Johnnie in their bar room epic of the depression years concluded, and I paraphrase, that "their story held no moral, their story told no tale". If my story has such a message, it could perhapsbe construed as reinforcing the oft-repeated dictums, true or false, that "history repeats itself" or "man never learns".Coal mining is by far our oldest major Australian industry except for agriculture. Its history is almost as old as that of settlement:For various reasons, there has been a glamour associated with metal mining ventures which prob...

Jan 1, 1976

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996