Search Documents

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

By Erceg MM

The Waft River gold deposit is hosted by low grade metasediments which have been intruded by a dacite/andesite porphyry complex. Wafi River is classified as a high sulphur, epithermal type gold deposit having: a high sulphur content, a close association with calc-alkalic igneous rocks, zoned advanced argillic and argillic alteration, and enargite group minerals. Gold occurs as minute inclusions in pyrite and pyrrhotite within intermediate dickite/kaohnite - interlayered illitic clay alteration zones. Central leached silicic, alunite and pyrophyllite zones and peripheral chloritic zones are low in gold. The gold mineralisation at Wafi is interpreted to have been predominantly caused by mixing of hot upwelling acidic magmatic mineralised fluids with cool, neutral meteoric/hydrothermal fluids within permeable sediments. Locallised high grade breccia zones are encountered within the porphyry. An initial resource in excess of I million ounces Au has been defined.

Jan 1, 1990

By N Arrys, A Jani, S Shahin

Optimising pit slope stability and reducing strip ratio of a mining operation are two key tasks in geotechnical engineering. With a growing demand for minerals and an increasing cost associated with extraction, companies are constantly re-evaluating the viability of mineral deposits and challenging their geological understanding. Within Rio Tinto Iron Ore (RTIO), the Structural Geology (SG) team investigate and collect critical data, such as point based orientations, mapping and geological inferences from adjacent pits to remodel deposits where previous interpretations have failed to account for structurally controlled slope failures. This work outlines the key methods utilised by the Structural Geology team which form the foundations of informed orebody knowledge and subsequent geotechnical design recommendations. This publication utilises the results from a recent analysis to highlight the benefits of this methodology and how it has impacted the economics of an operation through optimisation of a pit wall ‘cutback’ and crest relocation.

Sep 1, 2024

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By P Hayes, D Fadhlurrahman

Molten slags, fluxes and salts play key roles in a wide range of the high temperature industrial process applications, including metals production, refining and recycling, metal manufacturing processes, electrochemical metal production cells, batteries, and efficient heat transfer media. Recognising the importance and significance of fundamental scientific knowledge of these systems, the International MOLTEN Conference series was established to provide a forum to bring together leading academic researchers and industrial engineers to present and discuss the latest scientific ideas and findings, and their application in their respective fields. This article presents an analysis of the research carried out in this field over time in terms of the number of journal articles, fields and slag systems studied and geographical origin of the research.

Jun 19, 2024

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

Sublevel open stoping (S.L.O.S.) was introduced at Rosebery in 1972 in the wider ore blocks below 14 level, largely replacing cut and fill methods which had been in use up till that time. During 1973/74 the method produced 10% of primary stoping tonnes, and by 1981/82 it increased to 65%. Because of the increasing reliance placed on sublevel open stoping for primary stoping production, every effort was made in both planning and operating to: - maximise ore recovery and reduce dilution - increase productivity - reduce costs.

Jan 1, 1982

By R Grogan

Nautilus Minerals Inc is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.Economies depend upon four key types of capital: built, natural, financial and human. Natural capital consists of the ‘minerals, energy, plants, animals, ecosystems (climatic processes, nutrient cycles and other natural structures and systems) found on Earth that provide a flow of natural goods and services’ (Daly and Farley, 2004). Many ecosystem goods such as fish, fruit and water are already valued and sold in markets; however, some ecosystem services are not amenable to markets and have remained unvalued in traditional accounting methods, even though they provide significant value (such as flood protection, climate stability etc; Batker and Schmidt, 2015).There are now economic methods available to quantify and value natural capital and many non-market ecosystem services. When valued in dollars, these services can be incorporated into a number of economic tools, including benefit-cost analysis, accounting, environmental impact statements, asset management plans and rate of return on investment calculations. Their inclusion ultimately strengthens decision-making. When natural capital assets and ecosystem services are not considered in economic analysis, they are effectively valued at zero. This omission can lead to poor decisions, inefficient capital investments, higher incurred costs and losses due to unexpected events (Batker and Schmidt, 2015).In 2015 Earth Economics was commissioned by Nautilus Minerals Inc to conduct an independent, objective environmental and social benchmarking analysis of the proposed deep seabed Solwara 1 mine with terrestrial copper mines (referred to as ‘the report’). The report represents the first ever natural capital accounting and ecosystem goods and services framework for seabed mining.The report compares the proposed Solwara 1 mine with three terrestrial mines: Bingham Canyon (Utah, USA), Prominent Hill (South Australia, Australia), and Intag (a proposed mine in Intag Province, Ecuador), and provides a natural capital accounting assessment for all four operations.CITATION:Grogan, R, 2016. Natural capital accounting – a sea floor mining application, in Proceedings Life-of-Mine 2016 Conference, pp 2–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By J Evans-Wheeler

"The mandate of the 2005 VALMIN Code to provide ‘(all) reliable, thorough, understandable material information required by investors and their advisers when making investment decisions’ requires that due diligence for tenure be full and thorough. Yet a published due diligence would often appear to be simply a list of tenures allegedly held without any commitment as to the standing of the tenure as safe and secure or otherwise.The value of due diligence for tenure, as mandated in the 2012 JORC Code and the 2005 VALMIN Code, must focus on compliance rather than simply on ‘vital statistics’. Enforcement in every jurisdiction in Australia focuses on penalties (some more harsh than others) for non-compliance, which, in turn and most importantly, reflects directly on security of tenure. Some 22 Acts (on average) impinge on security of tenure and fundamentally underpin the security of any mineral asset.This paper will outline regulatory processes to demonstrate how tenure compliance is achieved and argue that the rigorous application of good practices in tenure evaluation will lead to more of this information being made available on a regular basis.The paper will then focus on further practical examples of tenure compliance failures, the application of these to the requirements of the JORC and VALMIN Codes and due diligence that failed to fulfil the mandate. Examples will be given that alerted other professionals using the JORC Code to complex geological and mining situations of which they were unaware in their valuations.Finally, the author will make a personal plea for tenure to be considered at the commencement of any reporting process.CITATION:Evans-Wheeler, J, 2016. The VALMIN code and tenure compliance – not just a list, in Proceedings Project Evaluation 2016, pp 112–121 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Siwiec A

The laboratory investigations which are necessary to evaluate the mineral processing effectiveness usually include density separation of narrow size fraction of the feed and one of the products. In each size - density fractions the content of valuable mineral has to be determined. These data and yield in each size - density fraction can be specified by a matrix of partition coefficients. They are counterparts of recoveries. These coefficients can be compared with the mean recoveries at each density or size fraction or the total recovery, to determine which density - size fractions are processed in the best or worst way. The basic categories are: vector of metal content l _i 1711, 7t2, òòò, ltM I ò vector of particle size distribution x = I d1, d2, ..., dN I ò matrix of partition coefficients P11, P12, Pi N P _ P21, P22, ..., P2 N PM1 PM2..., PMN These three conceptions allow one to determine all the basic metallurgical parameters of a mineral processing unit. Losses of valuable mineral are connected with: ò mineralogical composition of the ore (types of minerals, their properties, dissemination, crystallochemical affinity, type and properties of gangue minerals), ò applied technology and technical equipment (beneficiation as a stochastic process, processing methods, process control, intergrowth liberation, water quality). Examples of application of the analytical method proposed are given for zinc - lead and coal processing plants.

Jan 1, 1993

Large GDP increases in the Pacific Rim countries have been accompanied by similarly large increases in demand for oil products. In the case of residual fuels, this demand has been tempered by the substitution of other energy products such as coal or gas.In the region's developing and newly industrialised nations, it has not been possible to make the very large investements in infrastructure which allow other energy sources to be used for transportation. As a result, GDP growth has been mirrored in the demand growth for automotive fuels. Other non-sustitutable products such as lubricants have also benefitted by the region's GDP growth.The combination of a number of years of sustained growth, coupled with increasing quality requirements is now stretching the upgrading capacity of the region's refineries. If, as seems likely, the region continues to enjoy a high GDP growth rate, then this will be accompanied by increasing reliance on finished products coming out of the Middle East. The owners of the most simple form of refinery in which crude is simply distilled and the naphtha reformed into petrol will face major capital investments. If they decide not to bear this cost, they will face increasing problems in selling their surplus residual fuel oil at an economic price. Quality will become an increasingly important issue. Not only in the well publicised areas such as unleaded petrol, but also for products such as lubricants which play a major role in the efficiency of modem equipment. Quality of service such as hours of opening, ease of access, and service station facilities will also become increasingly important as the oil companies use these to attract customers and gain brand differentiation.

Jan 1, 1990

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By Woodhouse M, Drew GJ, Andrews DL

The Honeymoon nickel sulphide deposits are located 45 km south of Wiluna in the 2.7 Ga old Agnew-Wiluna greenstone belt in the NE of the Yilgarn Craton (Figure 1). Both disseminated and massive nickel sulphide deposits are present within the deformed and metamorphosed Honeymoon Well ultramafic complex and are hosted by distinctly different komatiitic lithologies (Gole et al, 1996). The deposit styles and host rock lithologies reflect formation in markedly different volcanic settings. Metasomatism has affected parts of the ultramafic complex, including sections of the sulphide deposits, and has had a marked impact on mineralogy and bulk sulphide compositions. The present indicated resource is 158 Mt at 0.71 per cent Ni in four deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1995). This includes a massive sulphide resource of 2.5 Mt at 3.36 per cent Ni.

Jan 1, 1996

This paper explores the use of a Process Safety Management (PSM) system to manage risk in the mineral processing and metallurgical refining industries. Important elements of a PSM system are described. International regulations and non-regulatory guidelines covering PSM for high hazard industries are reviewed. Case studies of incidents in the mineral processing and metallurgical refining industries are presented to understand the lessons learned from failure to manage risks using a PSM system. Conclusions are drawn to adopt PSM in the minerals and metals processing industry as a tool for loss prevention and risk management.

Jan 1, 2003

LITHOPROBE is a national, collaborative research grogram with the general objective of understanding the teotectonic evolution of the North American continent through multidisciplinary lithospheric studies in carefully selected areas of Canada. Six transect areas are investigating Precambrian evolution, although only in two of these is the research well evolved. The Archean Kapuskasing Structural Zone in Ontario is confirmed as an upthrust slice of upper to mid crust exposed at the surface. The Late Proterozoic Keweenawan mid-continent rift is shown to be the deepest known rift on Earth and the Grenville collisional zone of Ontario and Quebec involves crustal scale imbrication and ramping of deeply buried rocks to the surface. Two transect areas are investigating Phanerozoic evolution. In the Newfoundland Appalachians the geologically defined tectonostratigraphic domains do not coincide with lower crustal blocks defined by seismic reflection data. The Southern Cordillera Transect in western Canada is examining the nature, timing and dynamics of the assembly of the Cordillera, and particularly the role of accreted terranes. Work in the eastern and central segments has extended the known western limit of the North American craton at least IOO km westward and crustal-scale ramps associated with metamorphic core complexes have been identified.

Jan 1, 1990

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023