Search Documents

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and cesting campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and altei._acive, cheaper, additives for cementing hydraulic Fill.

Jan 1, 1980

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

A description is given of a detailed examination of a coal bore core and of attempts to predict properties of equivalent "as-mined" coal using the bore core data so obtained. The accuracy of the prediction was measured by testing independently a large sample of coal which was produced under near mining conditions from a site adjacent to the bore core. Very encouraging results were obtained particularly in the prediction of size and ash distributions and washability characteristics of run-of-mine Coal.

Jan 1, 1972

By T Bookless, J Pownell, D Meadows

The ever increasing trend of the gold price has meant that ore deposits that were previously considered too complex, or unattractive by virtue of their low gold grade, are now being investigated more closely. These ore deposits present a greater risk of failure than previously was the case. To ensure that the risk of project failure is reduced and the maximum value is derived from the deposit, its mineralogy, as well as other characteristics, should be well understood such that the optimum process can be designed.Quite often the flow sheet design is assembled using individual process components, from various sources, and without consideration of the complete system. Test work programs require careful planning and an open viewpoint in terms of comminution circuit design particularly with respect to ever increasing power costs across the globe. As an example, high pressure grinding roll (HPGR) technology in many cases offers better mineral liberation than the more traditional comminution devices and it does so at a reduced energy input, and yet HPGR test work is often restricted in its scope due to the perceived novelty of the technology and the resultant lack of generally agreed and accepted test work routes.In this paper the authors outline a typical HPGR test work process route driven by the needs of different ore types and illustrate that to optimise the project value, any test work program should start from the premise that thorough understanding of the ore is vital.CITATION:Bookless, T, Meadows, D and Pownell, J, 2013. Enhancing project value through a designed high pressure grinding roll test work program, in Proceedings World Gold 2013 , pp 291-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Vann

Geometallurgy is inherently multidisciplinary and it gains its power to deliver improved outcomes for the minerals industry by bridging silos between disciplines. This cross-disciplinary approach unlocks value, identifies (and avoids) value destruction and provides a pathway to better implementation of an energy efficient and sustainable minerals industry. Despite this promise, we argue that the cross disciplinary approach also represents the greatest threat to the success of geometallurgy. Some key cross disciplinary issues identified are:Geometallurgy has so far evolved in the technical sphere, mainly by collaborations of geologists and metallurgists. Consequently, in many cases the business dimensions and value have not been incorporated. Financial and risk evaluation viewpoints need to be assimilated into the geometallurgical paradigm. In fact, until such measures are integrated into practices, the value cannot be fully demonstrated.The historical and current efforts on geometallurgy have been highly focused on improved sampling and measurement of geometallurgical properties or appropriate proxies. This work has been driven by professional and academic geologists and metallurgical engineers. It is notable that mining engineers (who are critical in the value delivery of geometallurgy through changed planning approaches) have so far been at the margins, or absent. The construction of valid three dimensional (3D) geometallurgical models raises some important organisational, mathematical and geostatistical considerations. The enhancement of resource models to account for geometallurgical aspects must be managed carefully if the full value of geometallurgical thinking is to be realised.The use of 3D geometallurgical models to change business decision making and practices is the real nub of the problem. We believe sophisticated scenario based evaluation methods are required if the potential impacts of spatial rock properties on processes further down the mining value chain are to be realistically evaluated. Such changed practices require ‘whole of value chain thinking’ to embed this change into the business in an ongoing way.Because profitable geometallurgy demands changed approaches to business decision-making and also organisation of the firm (radically changed in some cases), the senior executive viewpoint must be incorporated into the language and thinking of geometallurgy. This is unavoidable if the establishment of a geometallurgical approach to project evaluation, development and operation is to be successful and sustained.A powerful analogy for the problem faced by geometallurgy is the transformation of safety culture in the mining industry in the past 20 years. We argue that, as in the safety revolution, explicit models, cultural change and management of the ‘soft’ dimensions of the problem are pivotal to success of geometallurgy. In light of this, we propose a model (‘the Geomet Curve’) that gives a framework and pathway for geometallurgy in seven steps. The implications of this model for technical and organisational steps required at different stages are discussed.

Sep 5, 2011

By C Grobler, M Recklies, G Jiang, I Taylor, M Morgan, G MacDonald, L Smith

The resource estimation of lateritic deposits, such as Aurukun, presents specific issues related to the lateral changes in thickness and elevation of the various horizontal layers (or zones) within the deposit where the x and y dimensions are orders of magnitude greater than the z dimension. The objective was to develop a three-dimensional (3D) block model that retained the vertical and lateral variation inherent in deposits of this type to allow full optimisation of the production plan without prior selection of an economic portion (enriched bauxite layers) of the profile at the resource estimation stage. The Aurukun bauxite deposit is held by Chalco Australia Pty Ltd (Chalco) and forms part of the world-class Weipa bauxite province, Cape York Peninsula, Queensland, Australia. The bauxite is predominantly pisolitic with an upper boehmite-rich zone and lower gibbsite-rich zone. The bauxite consists of both in situ and reworked domains, is overlain by a thin soil horizon and has kaolinite clay as a transitional base. A portable infrared mineral analyser (PIMA) was utilised on site, in addition to elemental assay, on each drill sample to determine the mineralogy, in particular levels of boehmite, gibbsite, kaolinite and reactive silica. As part of the scope of work, a field program was undertaken using large diameter Boart Longyear sonic drilling to acquire detailed density measurements across the deposit to allow compliance with Joint Ore Reserves Committee (JORC) reporting requirements. Interpretation of the stratigraphy was conducted on a hole by hole basis with definition of the zone layering based on stratigraphy, geochemistry and mineralogy. The zone boundaries were then modelled as 3D surfaces and used to constrain a block model. The block model estimation used the ordinary kriging method, with the estimation done in unfolded space and then refolded, therefore maintaining the zones irrespective of thickness or orientation. The unfolding process converts the real-world positions for both blocks and informing samples to a scaled position relative to the roof and floor of each zone. Analysis of the data and variography were also undertaken in unfolded space. The x and y dimensions are unchanged, but the z dimension is a relative position. The effect of the unfolding and limits on number of samples per hole is to æpushÆ the informing sample search sideways but within the stratification, rather than vertically. This honours the strong vertical zonation within the bauxite profile. The JORC Code requires that the stated resource must have æreasonable prospects for economic extractionÆ. This is a qualitative rather than quantitative definition. A number of selection criteria to define a resource roof and floor were developed in consultation with the project engineers and owners to meet these criteria. The vertical selection of material to include in the resource highlights the variation in the development (and destruction) of the bauxite profile from area to area within the deposit.

Jan 1, 2009

By P J. Howard

Atlas Iron Limited’s McCamey’s North project lies at the eastern end of the Hamersley Basin, approximately 50 km east of Newman, Western Australia, and 3 km northeast of BHP Billiton’s Jimblebar Mine. The presence of significant surface iron mineralisation identified during field reconnaissance, has subsequently been further defined by detailed mapping and RC drilling.The project area is dominated by outcrops of moderate to steeply north and south dipping banded iron formation, cherts and shales of the Boolgeeda Iron Formation overlying rhyolites and rhyodacites of the Woongarra Volcanics. In lower lying areas recent colluvium and alluvium mask the Archaean geology. Drilling and downhole geophysics has allowed a composite stratigraphic section to be compiled through almost the entire Boolgeeda Iron Formation.Surface orientations and subsurface stratigraphic correlations using natural gamma logs indicate large scale open folding about east-west trending fold axes across the project area; while small scale tight to isoclinal folding with similar fold axis orientations are visible at the outcrop scale. These folds are cut by a number of moderate to steeply south-dipping normal faults defining a series of north-dipping fault blocks which repeat the stratigraphy across the project area.Bedded iron mineralisation consists mainly of haematite-martite and goethite ores with best results of 78 m @ 60.5 per cent Fe. Vitreous goethite is observed at the surface of the mineralised horizons. The mineralisation exhibits a strong stratigraphic control and extend down-dip up to 120 m below surface. The strike extent of the mineralisation is still to be determined. An inferred resource of 39 Mt at 58 per cent Fe has been defi ned to date (ASX: AGO 3 February 2011).The fi ndings at McCamey’s North indicate that there is potential for economic iron mineralisation to exist in other areas of Boolgeeda Iron Formation within the Hamersley Basin.

Jul 11, 2011

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By G H. Luttrell

The use of secondary desliming cyclones ahead of froth flotation cells to reject ultrafine (-45 ¦m) particles has become a popular option in the United States for preparing fine coal feeds for froth flotation circuits. In light of this popularity, several experimental studies have been performed at industrial plant sites to develop a better understanding of the impacts of ultrafine desliming on froth cell performance and, ultimately, overall plant performance. These studies included an evaluation of various circuit configurations incorporating different flotation technologies (conventional machines and column cells) as well as different dewatering systems (disc filters, screen-bowl centrifuges, and thermal dryers). The data obtained from these studies indicate that deslime circuits offer several important benefits including lower product ash, reduced product moisture, better froth handling characteristics, and lower capital and operating costs. In addition, case studies conducted as part of this investigation have been used to develop generic guidelines for how deslime circuits may be successfully applied to improve the overall profitability of fine coal flotation circuits for both the metallurgical and steam coal markets.

Jan 1, 2005

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By Short KC

The Hunter Region, with a major part of the coal resources of New South Wales and a long history of coal mining, has experienced a rapid expansion of coal resource development in recent years. While there are inevitable conflicts between mining, urban development and related infrastructure, and between mining and other resources, the application of sound planning practices, and improved co-operation and co-ordination among the various parties, helps to reduce such conflicts. The planning process involves consideration of factors such as transport- ation (including port facilities), mine subsidence, provision for surface facilities, a,iC the need for buffer 'ones. In addition, provision must be made for urban expansion, often co-existing or in close proximity to present or future coal mining development. Approval of coal mining developments takes place within the legislative framework of the Environmental Planning and Assessment Act, 1979 (EPA Act), the Coal Mining Act, 1973 (CM Act) and the Mining Act, 1973. Considerable effort has gone into stream- lining and co-ordinating the procedures under these Acts. The EPA Act provides for regional and local environmental plans, as well as a linked process of development control and environmental impact assessment. The CM Act provides for the grant of exploration and coal mining titles and mechanisms for the responsible management of Mining.

Jan 1, 1987

By C Fountain

Australian mining and engineering companies have increasingly been investing in the mining industry in Brazil. It is a country of enormous mineral and agricultural wealth, with a well-established mining sector. Some Brazilian mining companies and personnel have been journeying in the opposite direction. There are significant differences in the approaches to engineering between the Australian and Brazilian industries that can cause confusion for companies operating in the other country. These range from differing expectations during the various stages of feasibility studies to style of plant and contracting strategies during the construction phase of projects. Some of the differences are driven by tax regimes, labour costs, or different settlement patterns. Others are the result of different histories and pressures on the industries in the two nations.This paper describes some of the differences in approach found in the two countries and some of the reasons for them.

Aug 8, 2011

The 1990s present many challenges, not the least of which is in the area of health and safety. Integrating of safety and health into the management process to suit the overall needs of a company will require commitment. Organisations which consistently perform to high success levels do so because they plan it that way. By using tools of total quality management, the potential to continually improve all safety processes exists. The successful integration of total quality measurement principles used in the improvement of safety processes, and the measurement of performance-based activities allow for prevention of accident causing scenarios and performance improvement.

Jan 1, 1993

By Hart A. T, Lanigan P. G

BHP is currently undertaking research into plasma are metallurgical processing at the Central Research Laboratories (CRL), Shortland. The use of high intensity plasma arcs for melting and smelting has a number of advantages, including; the ability to control atmosphere and furnace operating conditions, total enclosure, high temperatures, versatility, and low in-process inventory in a compact system. The intensive conditions, achievable in a plasma furnace system, make it particularly useful for the smelting and melting of difficult-to-treat materials, such as ore and metallic fines and refractory ores. Two transferred arc plasma smelting furnaces have been set up at CRL; a 100kg furnace is used for small scale melting and smelting studies and a 1 tonne furnace for pilot scale plasma processing studies and equipment development. Power is supplied by a 1MW GEC thyristor DC power supply. A 220kW DC power supply is available for "off site" pilot process trials and demonstrations, and a 150kW non-transfered are plasma torch is also available for other studies. The facility has been designed to allow maximum flexibility in researching and developing applications in metallurgical processing and transferring developed technology to company operations. The objectives behind the development of the facility, details of the facility and an outline of current research areas will be Discussed.

Jan 1, 1987

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

A number of mines in Australia have experienced premature detonations caused by bulk explosives reacting with the rock type being blasted. Premature detonations are extremely high risk events as they are unplanned, occurring at any place, at any time, potentially resulting in high loss (personnel and equipment). Many Australian mines have also experienced spontaneous combustion where spilt explosive reacts vigorously with the rock type. Premature detonation in these cases does not occur due to the lack of confinement and the volume of explosive present, but these reactions could impinge on the surface initiation system and provide an early warning of future premature detonations. The explosive ground reactivity phenomena is not restricted to Australia with similar incidents being reported in North and South America, South Africa, China and South East Asia. All reported incidents have two common denominators, being the presence of sulphide rock types and nitrate based explosives. Both premature detonation and spontaneous combustion result from the same series of reactions of partially weathered sulphides that ultimately result in the violent decomposition of the ammonium nitrate based explosive. A number of relatively easily observable indicators can be used to assess a particular minesiteÆs potential for explosive ground reactivity. The presence of two or more of these indicators means that minesite personnel should contact their explosives manufacturer for assistance in determining if a problem exists and if so then developing strategies to overcome the situation. The paper describes the indicators as well as discussing, via a case study, the holistic approach required to efficiently develop a relevant æSafe and Efficient Blasting ProcedureÆ to deal with explosive ground reactivity problems.

Jan 1, 1999

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022