Search Documents

By S Mitchell

Jetcrete Australia Pty Ltd, shotcrete contractor took the initiative in 2008 to discontinue the use of ‘road registerable’ concrete trucks for all underground works in Australia and internationally.The rationale for this decision was basic, safety. Historically these vehicles have been and still are involved in far too many accidents; this obvious trend needs to be addressed by engineering out the root cause of the problem which in this case is suitability for purpose.Road registerable concrete trucks have been widely used for the delivery of concrete in Australian mines for many years prior to and after the inception of wet shotcrete as ‘in cycle’ ground support in underground excavations around 1992. With this inception came a wide interest in the shotcrete process and an influx of new shotcrete contractors, all using road registerable concrete trucks to deliver the large volumes of Shotcrete required for these services and in turn largely increasing the use of these vehicles underground. The road registerable concrete trucks were difficult to control and each trip underground required the operators to maintain good management of the inherent risks. We virtually had no reasonable alternative for the industry and could only encourage the operators to drive with soft controls such as, reducing overall speed to a maximum of 15 km per hour when declining, regardless of the road conditions, coming to a complete halt prior to turning into any sharp corners, remaining in the same gear both inclining and declining.

Mar 21, 2011

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By B E. Hall, D B. Kahler

"'Optimisation' has become a catchcry among many mining companies looking to tell the market how mining businesses will be improved and shareholder value increased. Consequently, the term 'optimisation' has been adopted by many service providers as they look to assist mining companies in achieving their objectives. But the explosion of services and products being offered with the label 'optimisation' has created some confusion. Mining companies ask for help in 'optimising' and service providers offer their assistance because they have a product that has the word 'optimisation' in its title. This is of course an over-simplification, but not by much! The authors' discussions in recent years with both mining companies and service providers have uncovered a number of very different definitions of optimisation.This paper provides a framework for identifying the scope and approach of different mining optimisation products and services, particularly the distinction between optimisation of components of the operation and the business as a whole. The different types of business optimisation are discussed, highlighting the failings of the mining industry's typical approach of strategy selection (as opposed to strategy optimisation). Mining business optimisation is discussed as a wicked problem, with the implication of this on how strategy optimisation models should be used and what the objectives of a business optimisation study should be.Case studies are also included to illustrate how fully flexible strategy optimisation models have been applied to assist decision-makers understand the impacts of changes in one part of the operation on the whole mining and treatment process, from geological models to the sale of product to customers.CITATION:Kahler, D B and Hall, B E, 2016. Strategic decision-making in mining – business optimisation using flexible evaluation models, in Proceedings Project Evaluation 2016, pp 215–225 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024

By C Pope, M Tannock

Mining exploration and development projects in Australia are being negatively affected by the highly complex regulatory and bureaucratic processes at all levels of government. These processes affect mining companies operating in Australia by impacting on timelines and the cost of developing a mining project. It is not uncommon for the granting of project approvals to take in excess of five years, meaning that mining companies struggle with productivity, efficiency, time frame and cost issues in respect to their projects in Australia. As the mining boom in Australia is moving from the investment to the production phase, it is now more important than ever to maintain a regulatory landscape that facilitates rather than discourages new investment.While one of our key arguments is that there is too much burdensome regulation and red tape in Australia, we are also strongly believe that regulatory intervention is necessary to ensure that appropriate checks and balances are in place to serve the public interest and manage environmental, health and safety, social and other development-related impacts that may arise from a mining project. However, the regulatory intervention in Australia has come to a point where it is excessive and starting to discourage valuable investment in mining projects for nominal return to the public. Excessive regulation or ‘red tape’ impedes productivity and competitiveness, deters investment and innovation and costs jobs, all of which ultimately impact on the growth of Australia and the standard of living of all Australians.This paper aims to examine and compare the federal, state and local regulations that govern mining projects in Australia. It will highlight how these regulations are unnecessarily complex, lengthy and duplicated and how they can be streamlined to reduce red tape. In doing so, the paper will evaluate the recommendations proposed by the Productivity Commission Report on Major Project Assessments released in 2013, which include the recommendation to move to a ‘one project, one assessment, one decision’ regulatory model.CITATION:Pope, C and Tannock, M, 2015. Project development and regulation red tape – a comparative analysis: does it need to be so complex?, in Proceedings Iron Ore 2015, pp 621–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

By C DahnTr-Lindqvist

The Kiruna mine produced about 19 Mt processed iron ore in 1999 using sublevel caving. General failure in the hangingwall has been widely studied and its mechanism is rather well understood. Failure in the footwall is more recent and not perfectly explained. Plane shear failure and Hoek and BrayÆs circular failure charts were successfully used to match the first surveyed failure surfaces. The footwall is not free yet but covered by a caved waste rock abutment whose exact behaviour is poorly known. Based on new field data and numerical models (FLAC), the following paper presents recent improvements in understanding the Kiruna mineÆs footwall failure process.

Jan 1, 2000

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By T Brown

Australia is now committed to the most significant period of infrastructure investment since the 1960s and the current climate of project finance and public private partnership (PPP) model uncertainty means it is imperative that the affordability and certainty in delivery of infrastructure projects is maximised.In light of the current and forecast levels of infrastructure investment it is worth drawing comparison with a similar period of Australian expansion when the nation’s first railways were constructed. Similarly to over a century ago, we are following a trend in rapid development and are already reaping the inefficiencies that could be avoided with broader technical planning and improved client coordination.The original rail networks were developed by the individual states before they combined to form a Federation of states in 1901. As a result of the adoption of different gauges by 1917 a passenger wanting to travel by train from Brisbane to Perth had to change trains six times.Similarly in 2011, there is little parity between Australian states on the quality requirements (performance specifications) for road tunnels. Differences between states start most significantly with the size of the specified traffic envelopes, thus the size of tunnel required. Where ambiguity and differences exist in project documentation, performance specifi cations (PS) and broad technical requirements for road tunnel projects, any associated risk in interpretation ultimately ends up being incorporated in the bidder’s (constructor’s) final sell price.Whilst not nearly as inconvenient as having to change train at each state border, and largely unnoticed by the general tax paying motorist, this paper examines examples of apparent minor differences in Australia’s recently constructed road tunnels to highlight the differences in road tunnel specifications.The paper identifies how these small differences manifest themselves in major price penalties between projects and further, highlights the need for further specification review, refinement and standardisation across road tunnel jurisdictions to increase road tunnel affordability.

Mar 8, 2011

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Scoble

This paper addresses the importance of collaborative approaches to resolving future mining challenges. It attempts to provide some insight into understanding the theory, measurement, mapping and management of collaboration. This is related to the design and planning for successful research and educational initiatives. Reference is made to Canadian and global case studies and personal experiences.

Nov 22, 2011

By R Norris, M Dunne

Mining and mineral processing is expected by society and obliged by law to operate in an environmentally friendly fashion, minimising the impact on and avoiding damage to the environment. Substantial efforts by the industry, as well as by process and equipment designers have resulted in many innovative developments, which show that operating in an environmentally responsible manner can be achieved in a cost-effective way. This paper showcases five emerging equipment best practices in industry including installation examples. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. The belt press filter is a small fraction of the operating and capital cost of alternative dry tailings technologies. This gives operators who must dry their tailings a competitive advantage and makes such ægreenÆ operations much more sustainable. The filtercake is disposed with other plant rejects, eliminating the need for tailings dams to be constructed and thus also often increasing mine reserves. Mining applications include coal tailings, sand tailings, sinter plant waste and power station fly ash. Screen-scroll and vibrating centrifuges are widely used in the coal, potash and salt industries to dewater the product to low surface moistures. Inclined plate Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the worldwide production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By D Lozada, A Salazar

Geometallurgy is a tool that, for more than a century, has been present in the implicit operations of mineral beneficiation. There’s a need to understand the characteristics of the material to be processed. This has led metallurgists to ask geologists what type of rock and mineralogy is entering the Beneficiation Plant and vice versa. The geologist needs to understand the beneficiation process in order to be able to carry out the production programming. The paradigm is whether geometallurgy can be applied to small-scale mining or if it is only aimed at large companies that invest millions of dollars to conduct studies. With this work, we provide an example of how geometallurgy can help improve the processes of a small mining company located in Ecuador (South America). We performed characterizations of geological and mineralogical and metallurgical tests in universities and the National Research Institute of Geological Metallurgical Mining. The origin of the theme is based on the fact that gold has been detected in the final tailings. The flotation concentrates meet the standards in terms of the content of economically profitable metals, but this isn’t the case with regards to the percentage of arsenic, which has hindered sales. The hypothesis is: conducting technical and scientific research will optimize the metallurgical process for the recovery of gold and concentrates. The referential framework is the mining geology of the Bella Rica District, current status of the Beneficiation Plant. In the theoretical framework there are parameters of the veins, comminution operations, gravimetric concentration, flotation, and cyanidation. The methodological framework contemplates the characterization of the gold ore, the chemical, mineralogical, textural, metallurgical analysis and the interpretation of the results. Thus, the design of a geometallurgy model of the deposit, with its main characteristics, is a conclusion that serves as a basis for the proposal of the optimization of the metallurgical process.CITATION:Lozada, D and Salazar, A, 2018. Geometallurgy applied to small-scale mining: a case study, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Morgan, D J. Bradshaw, S Schwarz

The characterisation of the flotation kinetic response in future mining deposits is important because the flotation response is affected by changes in ore mineralogy. Current methods for characterising the flotation response of different ore types, such as the JK floatability index test (JKFIT) methodology, require at least 10 kg of feed material. In geometallurgical applications, this material is taken from core samples. Core samples are generally obtained using specialised drills and are limited in nature. Thus, it would be beneficial to develop a laboratory technique that required less sample material but still characterised the flotation response of different ore types. The JK mineral separation index (JKMSi) is a small-scale flotation test that requires significantly less feed material (10 g of sample/data point). This study aims to investigate the JKMSi system kinetics and to validate this technique using the JKFIT proven methodology. The JKMSi flotation kinetics were manipulated by varying selected system parameters. The relationship between these parameters and mineral recovery was used to obtain floatability characteristics of the ore. For an ore sample containing chalcopyrite and pyrite, it was found that the chalcopyrite floatability parameters determined from both the JKMSi and JKFIT tests were of the same order of magnitude and the mass fractions of the fast, slow and non-floating components were similar. For pyrite, the floatability parameters were not of the same order of magnitude, but modifications to the test procedure have been identified, which may correct this.CITATION:Morgan, S, Bradshaw, D J and Schwarz, S, 2012. Julius Kruttschnitt Mineral Separation Index - Small-scale test to characterise the flotation response of an ore type, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 159-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012